• Title/Summary/Keyword: 전달각

Search Result 2,093, Processing Time 0.034 seconds

Manufacture of Low-Speed Type Inductive Coupler Using Nano-Crystalline Alloy (나노결정 합금재료를 이용한 저속형 비접촉식 커플러의 제조)

  • Kim, Hyun-Sik;Kim, Jong-Ryung;Lee, Jun-Hui;Lee, Hae-Yeon;Huh, Jung-Sub;Oh, Young-Woo;Byun, Woo-Bong
    • Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
    • /
    • 2007.11a
    • /
    • pp.228-228
    • /
    • 2007
  • 전력선 통신용 비접촉식 커플러는 고속형(2~30 MHz)과 저속형(100~450KHz)으로 나누어 볼 수 있는데, 고속형은 현재 국내에서 독자적으로 개발되어 다양한 모델이 적용되고 있는 상황이지만, 저속형은 시작품수준으로 제조되어 있으나 신호전송 특성의 향상절구가 필요한 상황이다. 전력선 통신용 커플러는 전력선 또는 모뎀으로 통신신호를 전달하는 기능을 하는 것으로서, 전력선 통신을 위한 핵심부품이다. 따라서 본 연구에서는 100~450 KHz 대역에서 사용 가능한 저속형 비접촉식 커플러를 제조하기 위해, 권선조건, 대전류형 자심재료의 모의 해석, 노이즈 필터조건, 임피던스 매칭, 하우징방법 등의 각 공정 변수를 확립하고자 하였다. 자심재료의 모의해석에서 자심재료의 높이와 전력선 도체 단면적 변화는 자심재료의 전류포화특성에 영향을 미치지 않으며, 유효길이와 에어-갭 크기가 증가할수록 전류포화특성은 향상되는데, 자심재료의 내경이 64 mm일 때 자심재료의 폭((외경-내경)/2)은 15 mm 이상이어야 하고, 에어-갭은 약 $600\;{\mu}m$ 정도의 에어-갭을 형성시켜야함을 확인할 수 있었다. 또한 저속용 비접촉식 커플러 제조조건 실험에서 내경${\times}$외경${\times}$높이가 $64{\times}94{\times}140mm$인 자심재료를 이용하여 권선 수와 에어-갭을 각각 3회, $400{\sim}600\;{\mu}m$ 삽입했을 때, 가장 우수한 특성을 나타내었다. 그리고 저역 통과 필터를 출력부에 내장하여 통신신호 이외의 노이즈를 제거할 수 있었다. 본 연구에서 제조된 300 A급 지중선용 저속형 비접촉식 커플러는 내경${\times}$외경${\times}$높이가 $58{\times}1144{\times}158mm$이고, 100~450 KHz 통신대역에서 약$7{\pm}2dB$의 삽입손실을 나타내었다.

  • PDF

The Effect of Patients Positioning System on the Prescription Dose in Radiation Therapy (방사선치료 시 자세확인시스템이 처방선량에 미치는 영향)

  • Kim, Jeong-Ho;Bae, Seok-Hwan
    • Journal of radiological science and technology
    • /
    • v.40 no.4
    • /
    • pp.613-620
    • /
    • 2017
  • Planning dose must be delivered accurately for radiation therapy. Also, It must be needed accurately setup. However, patient positioning images were need for accuracy setup. Then patient positioning images is followed by additional exposure to radiation. For 45 points in the phantom, we measured the doses for 6 MV and 10 MV photon beams, OBI(On Board Imager) and CBCT(Conebeam Computed Tomography) using OSLD(Optically Stimulated Luminescent Dosimeter). We compared the differences in the cases where posture confirmation imaging at each point was added to the treatment dose. Also, we tried to propose a photography cycle that satisfies the 5% recommended by AAPM(The American Association of Physicists in Medicine). As a result, a maximum of 98.6 cGy was obtained at a minimum of 45.27 cGy at the 6 MV, a maximum of 99.66 cGy at a minimum of 53.34 cGy at the 10 MV, a maximum of 2.64 cGy at the minimum of 0.19 cGy for the OBI and a maximum of 17.18 cGy at the minimum of 0.54 cGy for the CBCT.The ratio of the radiation dose to the treatment dose is 3.49% in the case of 2D imaging and the maximum is 22.65% in the case of 3D imaging. Therefore, tolerance of 2D image is 1 exposure per day, and 3D image is 1 exposure per week. And it is need to calculation of separate in the parallelism at additional study.

Enhancement of SNUF Active Trailing-edge Flap Blade Mechanism Design (SNUF뒷전 플랩 블레이드 메커니즘의 설계 개선)

  • Natarajan, Balakumaran;Eun, WonJong;Shin, SangJoon
    • Transactions of the Korean Society for Noise and Vibration Engineering
    • /
    • v.23 no.7
    • /
    • pp.645-653
    • /
    • 2013
  • Seoul National University flap(SNUF) blade is a small-scale rotor blade incorporating a small trailing-edge flap control surface driven by piezoelectric actuators at higher harmonics for vibration attenuation. Initially, the blade was designed using two-dimensional cross-section analysis and geometrically exact one-dimensional beam analysis, and its material configuration was finalized. A flap-deflection angle of ${\pm}4^{\circ}$ was established as the criterion for enhanced vibration reduction based on an earlier simulation. The flap-linkage mechanism was designed and static bench tests were conducted for verifying the performance of the flap-actuation mechanism. Different versions of test beds were developed and tested with the designed flap and the selected APA 200M piezoelectric actuators. Through significant improvements, a maximum deflection of ${\pm}3.7^{\circ}$ was achieved. High-frequency experiments were conducted for evaluating the performance, and the transfer function of the test bed was determined experimentally. With the static tests almost complete, the rotor power required for testing the blade in a whirl tower (centrifugal environment) was calculated, and further preparations are underway.

Glucocorticoid Regulation of Gene Expression in Hippocampal CA3 and Dentate Gyrus (글루코코티코이드 호르몬에 의한 뇌해마의 CA와 Dentate Gyrus 부분의 유전자 발현 변화)

  • Kim, Dong-Sub;Ahn, Soon-Cheol;Kim, Young-Jin;Park, Byoung-Keun;Ahn, Yong-Tae;Kim, Ji-Youn;Kyoji, Morita;Her, Song
    • Journal of Life Science
    • /
    • v.17 no.3 s.83
    • /
    • pp.305-311
    • /
    • 2007
  • Glucocorticoids (GCs) alter metabolism, synaptogenesis, apoptosis, neurogenesis, and dendritic morphology in the hippocampus. To better understand how glucocorticoids regulate these aspects of hippocampal biology, we studied gene expression patterns in the CA3 (Hippocampal pyramidal cell field CA3) and dentate gyrus (DG). Litter-matched Lewis inbred rats treated for 20 days with either 9.5 mg per day sustained-release corticosterone or placebo pellets were compared with high-density oligonucleotide microarray analysis (Rat Neurobiology U34 Arrays, Affymetrix). In placebo-treated rats, 32 genes were expressed at greater levels in CA3 than DG, whereas 3 genes were expressed at great levels in DC than CA3. Regional differences were also apparent in corticosterone-induced changes in the hippocampal transcriptome. Six genes in CA3 and 41 genes in DC were differentially regulated by corticosterone. As per the glucocorticoid effects on gene transcription in the brain, forty three of these genes were upregulated, and 4 genes were downregulated. Genes differentially expressed in hippocampus included those for 13 neurotransmitter proteins, 5 ion channel related proteins, 4 transcription factors, 3 neurotrophic factors, 1 cytokine, 1 apoptosis related protein, and 5 genes involved in synaptogenesis. Interestingly, GCs can have suppressive effects on brain BDNF mRNA transcription, one of the neurotrophic factors. These results indicate the diversity of targets affected by chronic exposure to corticosterone and highlight important regional differences in hippocampal neurobiology.

GIS spatial D/B formation of geothermal data and Distribution of Heat Flow of Korea (한국의 지열자료 GIS 공간 D/B 구축과 지열류량 분포)

  • Kim, Hyoung-Chan;Lee, Young-Min;Park, Jeong-Min
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2006.06a
    • /
    • pp.459-460
    • /
    • 2006
  • 현재 남한의 지열류량 측정값으로는 총 363개 지점의 자료가 측정 및 수집되어 있다. 이것은 Mizutani et at. (1970), 장정진 외(1970), 그리고 서정희(1976) 등의 자료, 총 35개의 자료도 추가된 것이다. 1989년 이후부터 측정된 지열류량 자료는 217개 자료이며(임정웅 외, 1989; 임정웅 외, 1996; Lim and Kim, 1997; 염병우 외, 1997), 모두 직접 측정한 것이나, 1989년 이후 보고된 지열류량 자료에 약간의 오류가 있어 이번 연구에서 수정 보완하였다. 또한 과거의 자료 35개 자료는 이미 지열류량 측정치가 논문화 되어 있는 것으로 암석시료는 없다 1989년 이후 2004년까지 자료 217개 2005년도 추가 자료 111개의 지열류량 자료는 암석시료도 있으며, 측정기기가 서로 달라 오차가 있을 수 있어 서로 보정을 해야 할 필요가 있어 시추공 주변 암석을 새로 수집해서 신장비로 다시 측정 보정하였다. 지열류량 D/B 구축은 각 자료의 일련번호, 고유번호 (Sn.), 위경도 좌표 (longitude, lattitude), 암석의 열전도도(thermal conductivity), 지온경사 (thermal gradient), 지열류량 (heat flow)등으로 구성되어 있다. 지열류량 자료 공간 데이터베이스는 점 속성을 가지며 자료형태는 각종 소프트웨어와 호환성이 좋은 shape 파일 형태로 작성하였다. 또만 최근 천부 토양 및 암석 열물성을 이용한 냉난방시스템 즉, Heat Pump System 설계를 위하여 반드시 들어가야 하는 요소인 열확산율, 공극율, 밀도, 비열 등 열물성 특성을 추가하여 GIS 공간 D/B구축하였다. 대륙붕 자료 4개 자료를 제외하고 359개의 지열류량 자료를 이용하여 한반도 남부, 즉 남한의 지열류량 분포도를 작성 분석해 본 결과(그림 1), 우리나라의 지열류량 이상대는 아산만 주변, 보령, 유성, 진안, 울진, 포항, 부산 지역과 포천, 속초, 충주, 수안보 등 지역에서 나타난다 이러한 이상대 주변에는 대개 온천이 발달되어 있었거나 새로 개발되어 있는 곳이다. 온천에 이용하고 있는 시추공의 자료는 배제하였으나 온천이응으로 직접적으로 영향을 받지 않은 시추공의 자료는 사용하였다 이러한 온천 주변 지역이라 하더라도 실제는 온천의 pumping 으로 인한 대류현상으로 주변 일대의 온도를 올려놓았기 때문에 비교적 높은 지열류량 값을 보인다. 한편 한반도 남동부 일대는 이번 추가된 자료에 의해 새로운 지열류량 분포 변화가 나타났다 강원 북부 오색온천지역 부근에서 높은 지열류량 분포를 보이며 또한 우리나라 대단층 중의 하나인 양산단층과 같은 방향으로 발달한 밀양단층, 모량단층, 동래단층 등 주변부로 NNE-SSW 방향의 지열류량 이상대가 발달한다. 이것으로 볼 때 지열류량은 지질구조와 무관하지 않음을 파악할 수 있다. 특히 이러한 단층대 주변은 지열수의 순환이 깊은 심도까지 가능하므로 이러한 대류현상으로 지표부근까지 높은 지온 전달이 되어 나타나는 것으로 판단된다.

  • PDF

Development of the Robot Manipulator for Kinematies (기구학적 분석을 이용한 로봇 매니퓰레이터 개발)

  • Min, Byeong-Ro;Lee, Dae-Weon
    • Journal of Bio-Environment Control
    • /
    • v.13 no.1
    • /
    • pp.1-7
    • /
    • 2004
  • This study is kinematics for the manipulator development of cucumber harvesting. A theory value was verified by repeated error measurement after the forward kinematics or inverse kinematics analysis of manipulator. Manipulator is consisted of one perpendicular link and two revolution link. The transformation of manipulator can be valued by kinematics using Denavit-Hartenberg parameter. The value of inverse kinematics which is solved by three angles faction shows two types. Repeated errors refered maximum 2.60 mm, 2.05mm and 1.55 mm according to X, Y, Z axis. In this study, the actual coordinates of maximum point and minimum point were agreement in the forward kinematics or inverse kinematics. The results of repeated error measurement were reflect to be smaller compared to a diameter of cucumber. measurement errors were determined by experimented errors during the test. For reducing errors of manipulator and improving work efficiency, the number of link should be reduced and breeding and cultural environment should be considered to reduce the weight and use the hard stuff. The velocity of motor for working should be considered, too.

Performance Comparison of the Recognition Methods of a Touched Area on a Touch-Screen Panel for Embedded Systems (임베디드 시스템을 위한 터치스크린 패널의 터치 영역 인식 기법의 성능 비교)

  • Oh, Sam-Kweon;Park, Geun-Duk;Kim, Byoung-Kuk
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • v.10 no.9
    • /
    • pp.2334-2339
    • /
    • 2009
  • In case of an embedded system having an LCD panel with touch-screen capability, various figures such as rectangles, pentagons, circles, and arrows are frequently used for the delivery of user-input commands. In such a case, it is necessary to have an algorithm that can recognize whether a touched location is within a figure on which a specific user-input command is assigned. Such algorithms, however, impose a considerable amount of overhead for embedded systems with restricted amount of computing resources. This paper first describes a method for initializing and driving a touch-screen LCD and a coordinate-calibration method that converts touch-screen coordinates into LCD panel coordinates. Then it introduces methods that can be used for recognizing touched areas of rectangles, many-sided figures like pentagons, and circles; they are a range checking method for rectangles, a crossing number checking method for many-sided figures, a distance measurement method for circles, and a color comparison method that can be applied to all figures. In order to evaluate the performance of these methods, we implement two-dimensional graphics functions for drawing figures like triangles, rectangles, circles, and images. Then, we draw such figures and measures times spent for the touched-area recognition of these figures. Measurements show that the range checking is the most suitable method for rectangles, the distance measurement for circles, and the color comparison for many-sided figures and images.

The action plan of community-based governance for the realization happy life zone in Jeju (제주행복생활권 민관협치 구현 방안 연구)

  • Yang, Sung-Soon;Hwang, Kyung-Soo;Kim, Kyung-Bum
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • v.17 no.9
    • /
    • pp.178-187
    • /
    • 2016
  • The purpose of this study is to analyze governance in the business processes of Jeju's proposed 'Happy Living Area.' This study found Jeju's 'Happy Living Area' plans for governance were realized and conflicts may frequently occur in future business processes. Furthermore, roles and support systems were measured for the development council of 'Happy Living Area.' This paper reports findings from a case study on community planning for a public art project. This study recommends public-private governance in terms of process factors as well as role considerations. With respect to process factors, administrative agencies and citizen participation are examined. Second, the Living Area Council should play a mediating role between central and local governments as well as residents. Third, Happy Living Zones' Advisory Centre should undertake an advisory role. Fourth, consultation between public and private sectors is needed to establish evaluation criteria for reviewing proposals from subordinate administrative agencies. Fifth, local government systems should be managed by autonomous municipalities. Concerning role considerations, a new 'Personality for Governance' position should be established for performing different roles in the project implementation stage.

A comparison of chlorhexidine release rate from three polymeric controlled release drug prototypes (제어방출형 소독제의 약물전달 체로 사용된 폴리머 유형에 따른 클로르헥시딘 제어 방출속도 비교)

  • Bok Young-Bin;Lee Doug-Youn;Lee Chang-Young;Kim Kyung-Nam;Kum Kee-Yeon
    • Restorative Dentistry and Endodontics
    • /
    • v.29 no.6
    • /
    • pp.548-552
    • /
    • 2004
  • Intracanal disinfection of infected root canal is one of important treatment procedure. This in vitro study aimed to evaluate whether the surface polymers of controlled release drug (CRD) can effectively control the release rate of chlorhexidine for root canal disinfection. Four CRD prototypes were prepared: Group A (n=12); The core device (absorbent paper point) was loaded with 40% CHX solution as control. Group B (n=12); same as group A, but the device was coated with chitosan. Group C (n=12); same as group A and then coated three times with 5% PMMA. Group D (n=12); same as group A and then coated three times with 3% PLGA. All CRD prototypes were soaked in 3 mL distilled water for experimental periods and the concentrations of released CHX from each CRD prototype were determined using a UV spectrophotometer. Results showed that release rate of CHX were the greatest in the non-coated group (control group), followed by the chitosan-coated group, the PLGA-coated group, and the PMMA-coated group (P < 0.05). This data indicate that surface polymers can control the release rate of CHX from the CRD prototypes.

End-to-end Packet Statistics Analysis using OPNET Modeler Wireless Suite (OPNET Modeler Wireless Suite를 이용한 종단간 패킷 통계 분석)

  • Kim, Jeong-Su
    • The KIPS Transactions:PartC
    • /
    • v.18C no.4
    • /
    • pp.265-278
    • /
    • 2011
  • The objective of this paper is to analyze and characterize end-to-end packet statistics after modeling and simulation of WiFi (IEEE 802.11g) and WiMAX (IEEE 802.16e) of a virtual wireless network using OPNET Modeler Wireless Suite. Wireless internal and external network simulators such as Remcom's Wireless InSite Real Time (RT) module, WinProp: W-LAN/Fixed WiMAX/Mobile WiMAX, and SMI system, are designed to consider data transfer rate based on wireless propagation signal strength. However, we approached our research in a different perspective without support for characteristic of these wireless network simulators. That is, we will discuss the purpose of a visual analysis for these packets, how to receive each point packets (e.g., wireless user, base station or access point, and http server) through end-to-end virtual network modeling based on integrated wired and wireless network without wireless propagation signal strength. Measuring packet statistics is important in QoS metric analysis among wireless network performance metrics. Clear packet statistics is an especially essential metric in guaranteeing QoS for WiMAX users. We have found some interesting results through modeling and simulation for virtual wireless network using OPNET Modeler Wireless Suite. We are also able to analyze multi-view efficiency through experiment/observation result.