• Journal of agriculture & life science
• /
• v.52 no.6
• /
• pp.81-88
• /
• 2018

This study analyzed the characteristics of 6 recyclable bulking agents which can replace sawdust and rice hulls that are commonly used in livestock manure composting. The content of all the hazardous chemicals found in the bulking agents used in this experiment was between 0.0 and 34.1 ppm, which was noticeably lesser than the maximum content levels of hazardous substances 5.0~900.0 ppm prescribed by the Rural Development Administration(RDA), which means that the bulking agents would be able to replace sawdusts and rice husks. The water content of the bulking agents ranged from a minimum of 12.4% to a maximum of 16.6% in the original state, which was much less than 60%, the optimal moisture content. These results indicate that they would be able to function fully as bulking agents. Their water absorption rate was in the range of minimum 31.9% ~ maximum 600.0%, which showed huge differences among the types of bulking agents. The most appropriate bulking agent in terms of water absorption rate was wood pellets. It was the highest in the wood briquette manufactured by A, which was followed by C and B in the order. The shear strength of the 5 types of bulking agents in the original state was 271.7 N on an average, the highest figure of all, except for the oak briquette whose shear strength could not be measured and the wood pellets in the absorption state. The shear strength in the dry and absorption states then followed, and were 78.0 N and 27.7 N on an average, respectively. The wood briquette of A recorded considerably lower shear strength than that of B and C. Overall, shear strength tended to increase according to lower water absorption rates. Since pine wood chips and oak cuts have relatively greater shear strength even in the absorbing state than the other materials, they will be able to endure some power in the case of stirring with pig droppings.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.25-25
• /
• 2021

점착성 유사는 비점착성 유사에 비해 1차입자의 크기가 작아 1차입자간의 점착력이 중요한 역할을 하는 유사를 말한다. 점착성 유사는 비점착성 유사에 비해 크기가 작아 입자의 전자기적 점착력의 영향을 무시할 수 없으므로 점착력으로 인해 입자들은 서로 응집하는 동시에 입자들 간의 충돌에 의하여 파괴되는 과정을 거친다. 이러한 응집과 파괴가 지속되는 일련의 과정을 응집현상이라 한다. 점착성 유사는 응집과정을 통해 일차입자보다 크기가 크며 수십 개에서 수천 개의 일차입자와 물의 덩어리인 플럭을 형성하게 된다. 흐름 내 존재하는 플럭의 응집현상에 가장 지배적인 영향을 미치는 인자로 난류 거동이 알려진 바 있다. 본 연구에서는 난류 거동에 따른 점착성 플럭의 입도분포 변화를 살펴보고자 하였으며, 점착성 유사 입도분포 모형을 개발하였다. 수치모형의 개발은 확률과정(또는 추계과정)의 개념을 바탕으로 한다. 점착성 유사의 응집현상을 구성하는 응집과정은 다양한 연구를 통해 메커니즘들이 규명된 것과 달리 파괴과정은 난류로 인해 발생하며 무작위한 것으로 여겨진다. 무작위한 플럭의 파괴과정을 확률과정으로 가정하고 매개변수 중 하나를 대수정규분포를 따르는 난수로 고려하였다. 개발된 모형의 검증은 연안지역에서 점착성 플럭의 거동을 측정한 연구결과와의 비교를 통해 수행하였으며, 흐름 유속의 연직분포와 유사 농도의 연직분포, 응집현상 이후 플럭의 평형크기와 입도분포가 모두 합리적으로 계산되는 것이 확인되었다. 더불어 모의 결과에서는 대수정규분포를 따르는 동일한 난수를 적용하였음에도 불구하고 하상으로부터 거리가 가까워짐에 따라 플럭입도분포가 단봉분포(Unimodal Distribution)와 이봉분포(Bimodal Distribution)가 모두 계산되는 것으로 나타났다. 이는 모형의 개발과정에서 플럭의 가능 최대 크기를 콜모고로브 길이규모로 제한한 것과 관련이 있다. 난류 흐름 내 존재하는 플럭의 크기가 응집현상을 통해 난류의 콜모고로브 길이규모까지 성장하는 경우, 난류의 전단응력이 급격하게 증가하여 파괴과정이 활발해지고 응집과정이 저하된다는 것은 널리 알려진 사실이다. 이러한 사실을 바탕으로 플럭의 가능최대 크기를 콜모고로브 길이규모로 제한하였으며, 하상으로부터의 거리에 따라 콜모고로브 길이규모의 변화로 인해 콜모고로브 길이규모 부근에서 하나의 최빈값이 추가로 나타나는 것으로 이해된다. 수치모의 결과로부터 얻어진 콜모고로브 길이규모와 입도분포 형태의 상관관계를 보다 정확하게 이해하기 위해 실측 자료들을 검토해 본 결과, 균질한 재료를 이용한 실험실 실험결과에서 플럭 이봉분포의 최빈값이 콜모고로브 길이규모와 일치하는 것이 확인되었다. 연안지역에서 측정을 수행한 자료들에서도 이봉분포 또는 다봉분포와 콜모고로브 길이 규모와의 상관성을 찾아볼 수 있었다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.2
• /
• pp.23-32
• /
• 2001

Rock masses are usually discontinuous in nature, as a result of various geological processes they have underdone and they contain rock joints and bridges. Crack propagation and coalescence processes mainly cause rock failures in tunnels. In this study, we focused on the crack initiation, propagation and coalescence process of rock materials containing two pre-existing open cracks arranged in different geometries. During uniaxial compression, wing crack initiation stress, wing crack propagation angle, and crack coalescence stress of Diastone gypsum and Yeosan Marble specimens were examined. And crack initiation, propagation, and coalescence processes were observed. Shear, tensile and mixed (shear+tensile) types of crack coalescence occurred. To compare the experimental results with Ashby & Hallam model, crack coalescence stress was normalized and it generally agreed with the experimental results.

• Composites Research
• /
• v.13 no.6
• /
• pp.9-22
• /
• 2000

The Rayleigh-Ritz procedure based on energy method is used to present analytically the natural frequencies and the critical buckling loads for four types of loading conditions: (1) uniaxial, (2) biaxial, (3) positive shear and (4) negative shear, of the rectangular, composite plates unidirectionally stiffened with box beam type stiffeners. In analysis the discrete stiffener theory is adopted to present the effect of stiffeners in the plate structure. The convergence study is presented to demonstrate the accuracy of the results. Contour plots of the vibrated and buckled mode shapes are shown for some examples. The effect of various parameters such as numbers, position, aspect ratio of stiffener and layer angle, aspect ratio of plate are focused.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5C
• /
• pp.286-294
• /
• 2011

In most digital cameras, images are obtained by a sensor overlaid by the color filter array (CFA) such as Bayer, demanding a demosaicking procedure to rebuild the full resolution color images. However, due to the nature of sensor, it is necessary to consider denoising step to remove the noise. In this paper, we analyze demosaicking and denoising jointly and show that the proposed method can solve the denoising issue by simple manner, well suppress different level of noises. The proposed algorithm yields comparable performances measured by several image quality assessment (CPSNR, SCIELAB, and FSIM), while the computational cost is low.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.814-819
• /
• 2017

The objective of this paper is to observe effects of an ignition position and time on the ignition transition. A gaseous oxygen and liquid kerosene are used for propellants with the shear-coaxial injector. In order to study the ignition delay time and combustion instability intensity, the pressure transducer was used. The ignition position was changed with the injector spacer. Sequences except the igniter operation time were fixed to compare the ignition time only. Initial pressure peak and ignition delay time increased as the ignition time was delayed. Also, the unstable flame development zone was detected as the igniter was away from the injector.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.543-548
• /
• 2013

This paper presents a design of magnetorheological (MR) damper for control vibration of washing machine. This design is based on the requirements such as small dimensions with high damping force, and minimal consumed energy. The MR damper is designed using the shear mode of MR fluid, and Bingham plastic model is used for optimization process. In this design, a multi-coil design is adopted for damper to enhance damping force and reduce optimally structural parts. In optimization process, ADPL (Ansys Parametric Design Language) program is applied. Base on the optimal parameters, MR damper is manufactured and tested. In evaluation of MR damper, a modified sliding mode control is formulated and applied in both simulation and experiment. Results of experiment show that the MR damper satisfy the requirement of damping force for vibration control of washing machine.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.4
• /
• pp.91-100
• /
• 2012

Soil-water characteristic curves (SWCCs), which represent a physical property in partially saturated soils, show the relation between volumetric water content and matric suction. The SWCCs exhibit hysteresis during wetting and drying, however experimental expressions used to describe SWCCs have generally ignored the hysteresis. In addition, the shape of SWCC may depend on the void ratio which is changed by soil skeleton deformations or hysteretic behavior under various loading conditions. Hence, it is necessary to understand, both empirically and analytically, the relationship between soil skeleton deformations and the SWCCs of various soils. The typical SWCCs experimentally have drying, wetting, and the second drying curve. The measurement of a complete set of hysteretic curves is severely time-consuming and difficult works, then the first drying curve of SWCC is generally determined to estimate the hydraulic conductivity and shear strength function of partially saturated soils. This paper presents the hydraulic-mechanical behavior of partially saturated soils (weathered soil and silty soil) for volume changes and hysteresis in SWCCs regarding the difference between the first drying and wetting curve.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.39 no.2
• /
• pp.153-159
• /
• 2012

The objective of this study was to assess the effect of salivary contamination on shear bond strength of pit and fissure sealant using several bonding agents by means of applying saliva at different stages of treatment. 56 teeth were randomly divided into one of seven groups (8 per group): (Group A, B) acid etching; (Group C, D, E) Adper$^{TM}$ Single Bond after acid-etching; (Group F, G) Adper$^{TM}$ Prompt L-pop. Saliva was applied to teeth surface of B, D, E, and G groups for 10 seconds. Especially, group D was contaminated after acid-etching and group E was contaminated with saliva after adhesive application. After light curing, all of the specimens were thermocycled and the shear bond strength tests were performed. The results were as follows. 1. In generally performed pit and fissure sealant group, shear bonding strength significantly differently reduced when was contaminated by saliva (p<0.05). However the group that was applied with bonding agent during pit and fissure sealant procedure, there were no significant differences in the kind of bonding agents nor the stage of contamination. 2. In group that was not contaminated by saliva during pit and fissure sealant treatment, Adper$^{TM}$ Single Bond yielded the highest bonding strength but there were no significant differences. 3. The failure pattern on the debonded surfaces shows that most specimens from groups using bonding agents showed cohesive failures while most specimens from groups that didn't use bonding agents showed adhesive failures.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2006.05a
• /
• pp.645-648
• /
• 2006

최근 컴퓨터의 급속한 보급과 영상처리기술의 발달로 금석학 분야는 인문학의 범주를 뛰어넘어 문화 정보 공유의 중요한 위치로 자리매김하게 되었다. 본 연구는 국내에서 처음 시도 되는 것으로, 수천년 정신문화 산물의 정보자료인 탁본을 영상으로 입력하여 디지털 데이터로 전환하고, 이를 공간 영역에서 종합 분석함으로 탁본영상 고유의 특성을 파악하고자 하였다. 탁본 원영상은 흑백의 두 영역으로 분할되는 완벽한 이진영상이나, 탁본뜨기 수작업과정을 거치면서 관측영상에는 영역간 색도의 혼재가 발생하고 얼룩무늬와 문양이 전체 영상에 분포한다. 이와같은 영상으로부터 필요한 문자나 문양의 정보를 추출하기 위한 전단계로 영상에 관한 종합적인 분석 작업을 하였다. 분석 기법으로는 공간분석법을 사용하였다. 역사적으로 유명한 대표적인 탁본을 위시하여 40여개의 탁본영상 샘플을 무작위로 선택하였고, 공간분석을 통해 색도분포특성과 영역간 색도 중복 및 영역형성 양상과 특성을 찾아내었다.