• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.272-273
• /
• 2015

DLC는 고경도, 화학적 안정성 및 고내식성, 내마모성 및 낮은 마찰계수로 인하여 여러 산업분야의 표면처리기술로 적용되고 있다. 하지만 DLC의 절연특성은 전기 산업 분야에 적용 한계가 있다. 이번 연구에서는 DLC를 연료전지 중 PEMFC(고체산화물 연료전지)의 금속 분리판 표면처리에 적용시키고자 하였으며, 높은 전도성과 고내식성의 Me-DLC박막 제작을 목표로 하였다. Cr을 Buffer layer로 하고 Cr과 DLC를 동시에 증착한 Cr-DLC 박막을 제작하였다. Cr-DLC코팅의 기계적 특성을 확인하기 위하여 나노인덴터를 이용하여 경도 및 탄성률을 측정하였으며, ball-on disk를 이용하여 마찰계수를 확인하였다. 각 샘플들의 전기전도성을 확인하기 위하여 4-point probe system을 이용하여 측정하였으며, 부식 저항 특성을 확인하기 위하여 1mole $H_2SO_4$ + 2 ppm HF 분위기의 전해질 내에서 동전위 분극시험을 통한 내식성 테스트를 하였으며, XPS를 통하여 Cr-DLC박막내의 구조적 특성을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1452-1454
• /
• 1997

Properties of flashover in polymer insulators are very important under pollution environments. It is necessary to analyse flashover characteristics whether insulators are still safe or not. A lot of precious information can be got out of polluted polymer insulators through leakage current measurement. The behavior of partial arc discharge leads to flashover directly. It is possible to measure partial arc discharge as leakage current pulses analysis. The shape of histogram reflects degree of pollution, wetting and voltage stress level. It can be expressed by Weibull distribution function.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.15-15
• /
• 2008

산화물 반도체가 실리콘 기반의 기술을 대체할 새로운 기술로써 주목을 받기 시작하면서, 산화아연을 이용한 박막트랜지스터가 많은 주목을 받고 있다. 여기에 기존의 $SiO_2$를 대체할 새로운 High-k Material에 대한 연구 또한 진행되고 있는데, 이들의 가장 큰 문제점중 하나는 Interface Charge Trap이며, 그에 따른 결과로 히스테리시스 특성이 나타나게 되고, 이는 소자의 신뢰성에 큰 걸림돌이 되고 있다. 이번 연구에서는, High-k Material들 중의 하나인, $HfO_2$를 게이트 절연막으로 사용함에 있어서 Interface Charge Trap이 발생하는 문제를 해결하고자 하며, Low-k Material중에서 비교적 높은 유전상수를 갖는 $Al_2O_3$를 Buffer Layer로써 사용하여, 히스테리시스 특성을 향상 시켰다.

• 전기의세계
• /
• v.14 no.2
• /
• pp.8-13
• /
• 1965

It is expected that the impurities contained in a solid state insulation material will affect a considerable influence on its break-down voltage, dielectric loss, and insulation resistance. In this thesis, as a preliminary experimental research for the investigation described above, the effect of metalic barrier between the electrodes on the creepin flash over discharge voltage along the surface of a solid insulation material has been investigated, and got some interesting results. It was found that generaly the flash over voltage rises when a metalic barrier is located between the electrodes. The results of this investigation will be taken into account as an important components on the insulation design to prevent the creeping flash over discharge in insulators, bushings, and so on.

• Proceedings of the KIEE Conference
• /
• 2005.07e
• /
• pp.73-75
• /
• 2005

In present measurement of moisture contents is used as one of method for estimating degradation of transformer. Most of people use Karl-Fischer titration method for detection moisture contents but this measurement is inconvenient method because we must analyze transformer oil-paper after dismounting transformer and sampling in field. Therefore we don't directly investigate them in field. In this paper we will introduce Recovery Voltage Method(RVM) that is new method for estimating measurement in field though dismounting facility. For measure of moisture contents using RVM in accordance with accelerated thermal aging we have made experimental test cell and aged at a temperature up to 140$^{\circ}C$ for 300 hours. And we have been measured at intervals of 100 hours using RVM 5462 made in fetter company.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.505-508
• /
• 1999

In this study, weight loss, ESDD, surface conductivity and leakage current were measured at the different saline solutions by salt fog method. The magnitude of leakage current was higher at higher conductivity of 2 S/m saline water, but weight loss ESDD and surface conductivity which are indices of degradation were lower. This is considered that the current includes mainly ohmic component which doesn\`t contribute to surface degradation. In addition, it is shown that FFT could be useful in measuring initial transition from hydrophobic to hydrophilic surface.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.56 no.1
• /
• pp.37-44
• /
• 2007

This paper describes characteristics for copper oxide growth of polyvinyl chloride(PVC) insulated wires by series arc. In this experiment, 600V IV wires were used, and characteristics of oxide growth and ignition process were analyzed in case load was 300W, 460W and 600W, respectively. In the result of experiment, covering materials were molten, carbonized and ignited, whereas, oxidized materials were grown in conducting material. During copper oxide was growing, contact voltages and power dissipations increased. When there is copper oxide growth, the waveform of current showed sinusoidal waveform, and the waveform of voltage showed modified waveform. Oxidized materials were heated at about $905^{\circ}C$, surface structure showed irregular shapes, and cross-section showed multiple cracks. And, the results of this experiment were applied to the fire cause analysis of fire evidence collected at the fire scene.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1912-1914
• /
• 2005

The electrical, chemical and mechanical characteristics in transformer insulations are changed due to thermal stress. It is known that characteristics of transformer insulations is deteriorated such as decrease of dielectric strength, deterioration of dielectric constant and tensile strength of paper as transformer oil and paper are aged by thermal stress. Furthermore, chemical characteristics of them are deteriorated as like increment of moisture contents and dissolved by-products in oil, etc. In this paper we have been investigated chemical characteristics of transformer by accelerated thermal aging. For this working we have made experimental test cell and aged at a temperature up to $140^{\circ}C$ for 500 hours. The oil-paper insulation samples have been measured at intervals of 100 hours. For analysis we used Karl-Fisher titration method and high performance liquid chromatography (HPLC).

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.270-272
• /
• 2009

This paper presents a basic data of the surface discharge characteristics for solid dielectric under non-uniform field in $N_2/O_2$ mixture gas. Used electrodes are needle and plane. Used solid dielectric is expoxy resin. With the variation of the mixture rates of the gas by 80[%]:20[%], 60[%]:40[%] and 40[%]:60[%] in same condition, we can obtain different surface dielectric strength. Increased Pressure and thickness caused increased surface dielectric strength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.225-226
• /
• 2007

나노 기술은 21 세기에 들어와 모든 산업에 고루 이용되며 미래를 이끌어 나갈 기숱로 평가되고 있다. 고압 회전기용 주절연재료의 개발에서도 에폭시에 나노충진제를 혼합하여 복합재료로 만드는 나노기술이 활용되고 있으며, 이러한 나노기술을 바탕으로 절연성능을 높이고, 열적, 기계적 안정성을 높이는 기술 개발에 관심을 기울이고 있다. 하지만 이러한 성능향상을 위해서는 반드시 에폭시 기지 내에 충진제가 골고루 분산되어야 하며. 에폭시의 점도로 인해 제조 과정에서 발생하는 기포의 생성은 시료의 제조에 큰 영향을 끼치게 된다. 본 연구에서는 이러한 점에 착인하여 무충진 시료와 제조과정에서 혼입될 수 있는 불순물, 족 분산을 위한 유기 용매를 제조과정에서 고의로 혼합하여 이에 따른 기계적/유전적 특성과 엉항를 살펴보았다.