• Korean Journal of Soil Science and Fertilizer
• /
• v.27 no.3
• /
• pp.168-178
• /
• 1994

Acid sulfate soils occur extensively in Gimhae area where they have been formed from the brackish alluvial sediments along the sea coast and river estuary. The strong acid environment enhances silicate weathering and thus affects the soil clay minerals. The minerals were identified through chemical, X-ray diffraction and thermal methods. The ratio of $SiO_2$ and $Al_2O_3$ in the clay fractions ranged from 3.14 to 3.77, indicating that the distribution of the clay minerals were 1 : 1 and 2 : 1 minerals. Cation exchange capacity in the clay fractions was low due to high contents of 1 : 1 minerals and hydroxy interlayered vermiculite(HIV). The B and C horizon rich in jarosite have large amounts of yellow streaks which reflect high content of $Fe_2O_3$ and $K_2O$. Vermiculite and illite were quantified from thermogravimetry(TG), kaolin minerals from both TG and differential thermal analysis(DTA), and HIV from X-ray diffraction analysis. The dominant clay minerals were kaolin minerals, vermiculite, illite and HIV. HIV considered to be formed, especially, in acid soil environments. The minor minerals were quarts, feldspar, jarosite, pyrite, hematite and goethite. Kaolin minerals were the most abundant clay minerals throughout the acid sulfate soil. Kaolin minerals, however, increased towards the top of horizons throughout the soils and HIV decreased towards the top of horizons in the soil of Gimhae series and Haecheog series. Alteration of HIV to kaolin minerals during weathering of low pH condition in deep soil horizons may explain the high quantities of kaolin minerals and the relatively low quantities of HIV in the soil at top horizons.

• Restorative Dentistry and Endodontics
• /
• v.32 no.3
• /
• pp.222-235
• /
• 2007

The objectives of this study was to evaluate the effect of thermocycling on the ${\mu}TBS$ (microtensile bond strength) to dentin with four different adhesive systems to examine the bonding durability. Freshly extracted $3^{rd}$ molar teeth were exposed occlusal dentin surfaces, and randomly distributed into 8 adhesive groups 3-steps total-etching (Scotchbond Multi-Purpose Plus; SM, All Bond-2; AB), 2-steps total-etching (Single Bond; SB, One Step plus; OS), 2-steps self-etching (Clearfil SE Bond; SE, AdheSE AD) and single-step self-etching systems (Promp L-Pop; PL, Xeno III; XE) Each adhesive system in 8 adhesives groups was applied on prepared dentin surface as an instruction and resin composite (Z250) was placed incrementally and light-cured. The bonded specimens were sectioned with low-speed diamond saw to obtain $1\times1mm$ sticks after 24 hours of storage at $37^{\circ}C$ distilled water and proceeded thermocycling at the pre-determined cycles of 0, 1,000 and 2,000. The ${\mu}TBS$ test was carried out with EZ-tester at 1mm/min. The results of bond strength test were statistically analyzed using one-way ANOVA/ Duncan's test at the a < 0.05 confidence level. Also, the fracture mode of debonded surface and the interface were examined under SEM. The results of this study were as follows ; 1. 3-step total etching adhesives showed stable, but bond strength of 2-step adhesives were decreased as thermocycling stress. 2. SE showed the highest bond strength, but single step adhesives (PL, XE) had the lowest value both before and after thermocycling. 3 Most of adhesives showed adhesive failure. The total-etching systems were prone to adhesive failure and the single-step systems were mixed failure after thermocycling. Within limited results of this study, the bond strength of adhesive system was material specific and the bonding durability was affected by the bonding step/ procedure of adhesive Simplified bonding procedures do not necessarily imply improved bonding performance.

• Korean Journal of Soil Science and Fertilizer
• /
• v.26 no.1
• /
• pp.1-9
• /
• 1993

A study was carried out to investigate the genesis and mineralogical characteristics of clay minerals in three different types of soil derived from the gray shale distributed in Kyeongbuk Province in Korea. The soils have been developed from parent materials of residuum (Daegu series, Sirye series), colluvium(Banho series), and alluvium (Bigog series) of the same origin of parent rock with a topographical sequence. The investigation mainly focussed on the mineralogical aspects of primary minerals of asnd and silt fractions, identification and quantification of clay minerals, and characterization of hydroxy-interlayered mineral (HIM) along with their chemical composition. The identification was done through analyses of chemical, X-ray diffraction, and thermal methods. The major clay minerals in the soils are illite, vermiculite, kaolin and HIM, while chlorite and mixed layer minerals such as illite/chlorite and illite/vermiculite were coexisted as a subsidiary minerals. The distribution of clay minerals, however, varies according to the location and types of parent material. In the soils derived from the parent material of residuum, the upper soil (Daegu series) shows higher of 2:1 type minerals such as illite, vermiculite, and HIM than 1:1 type mineral rich in the lower soil(Sirye series). Soils developed from the parent material of colluvium and alluvium were high in illlte and mixed layer minerals, but low in HIM compared with the residual soils. The predominant weathering sequence of the clay minerals in each soil could be inferred as follows according to the minerlogical distribution and quantification of clay minerals : Daegu series, illite ${\rightarrow}$ vermiculite ${\rightarrow}$ HIM ; Sirye series, vermiculite ${\rightarrow}$ kaolin minerals ; Banho sereies and Bigog series, illite ${\rightarrow}$ illlte/vermiculite and/or illite/chlorlte mixed layer ${\rightarrow}$ vermiculite.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.2
• /
• pp.113-120
• /
• 2010

An experimental investigation was carried out to examine the evaporative heat transfer characteristics of R-134a in a micro-channel heat exchanger. The micro-channel heat exchanger used in this study was a sort of plate heat exchanger. Micro-channels were fabricated on the SUS304 plate by the photo-etching process: 13 sheets of plates were stacked and bonded by the diffusion bonding process. The effects of the evaporating temperature, mass flux of R-134a, and inlet temperature of water were examined. As the difference between the inlet temperatures of R-134a and water increased, the heat transfer rate increased. The evaporative heat transfer coefficients obtained in this study range from 0.67 to 6.23 kW/$m^2{\cdot}^{\circ}C$. The experimental correlation for the Nusselt number as a function of the Reynold number and $\Theta$ was suggested for the micro-channel heat exchanger.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.4
• /
• pp.145-150
• /
• 2014

GaN nanorods were grown on the apex of GaN stripes by three dimensional selective growth method. $SiO_2$ mask was partially removed only on the apex area of the GaN stripes by an optimized photolithography for the selective growth. Metallic Au was deposited only on the apex of the GaN stripes and a selective growth of GaN nanorods was followed by a metal organic vapor phase epitaxy (MOVPE). We confirmed that the shape and size of the GaN nanorods depend on growth temperature and flow rates of group III precursor. GaN nanorods were grown having a taper shape which have sharp tip and triangle-shaped cross section. From the TEM result, we confirmed that threading dislocations were rarely observed in GaN nanorods because of the very small contact area for the selective growth. Stacking faults which might be originated from a difference of the crystal facet directions between the GaN stripe and the GaN nanorods were observed in the center area of the GaN nanorods.

• Journal of the Korean Ceramic Society
• /
• v.41 no.6
• /
• pp.444-449
• /
• 2004

The microwave dielectric properties of low temperature sintered BaO-Nd$_2$O$_3$-TiO$_2$ (here after BNT) with a Pb-based glass-ceramics were studied in order to investigate their applicability to Low Temperature Co-fired Ceramics (LTCC) for fabrication of multilayered Radio Frequency (RF) passive components module. The BNT ceramics, with 5∼30 wt% of PbO-TiO$_2$-A1$_2$O$_3$-SiO$_2$ based glass-ceramics, were sintered at 105$0^{\circ}C$, which is lower than 130$0^{\circ}C$, sintering temperature of pure BNT ceramics. With increasing the amount of the glass-ceramics, sintering rate of the ceramics become activated due to the softening of glass, resulting in low-temperature densification. BaO-Nd$_2$O$_3$-TiO$_2$ microwave ceramics with 20 wt% glass-ceramics exhibit sintered relative densities over 95% and dielectric constant of 72, quality factor of 1500, and temperature coefficient of frequency of +22 ppm/$^{\circ}C$. This enhanced dielectric properties are attributed to mainly the presence of crystalline phases PbTiO$_3$ within the Pb-based glass.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.270-276
• /
• 2020

3D printing is an additive manufacturing technology that can produce complex shapes in a single process for a range of materials, such as polymers, ceramics, and metals. Recent 3D printing technology has developed to a level that enables the mass-production through an improvement of the printing speed and the continuous development of applicable materials. In this study, 3D printing technology using a laser was applied to manufacture a heat exchanger for an air compressor in a railway vehicle. First, the optimal design of the heat exchanger was carried out by focusing on weight reduction and compactness as a shape suitable for 3D printing. Based on the design derived, heat exchanger prototypes were made of AlSi10Mg alloy material by applying the SLM technique. Moreover, the manufactured prototypes were attached to an existing air compressor, and the heat exchange performance of the compressed air was tested. The test results of the 3D printed prototypes showed a heat exchange performance of approximately 80% and 85% at low and high-pressure, respectively, compared to the existing heat exchanger. From the 𝓔-NTU method results with an external cooling air condition similar to that of the existing heat exchanger, the calculated heat transfer amount of 3D printed parts showed similar performance compared to the existing heat exchanger. As a result, the 3D printed heat exchanger is lightweight with good performance.

• Journal of Adhesion and Interface
• /
• v.21 no.3
• /
• pp.93-100
• /
• 2020

3D printing technology enables proper objects to be made through an additive manufacturing method, but resulting in dimension deviation of the product due to contraction phenomenon as cooling melted filament resin injected from high-temperature use environment. In this research, we studied on acrylic adhesives for 3D printer build sheet in order to fabricate high-quality products with a precise shape and to well-mount without distortion. The solvent-free UV-curable acrylic adhesive formulation was designed by adding 4-acryloylmorpholine (ACMO) with high adhesion, toughness, glass transition temperature so that adhesion properties are stable at high temperature and products are easily mounted/detached from the adhesives. The designed formulation was polymerized through two-steps using post-addition of monomers. Using this, the acrylic adhesive was coated to make a film and then analyzed using various experimental techniques. As a result, the fabricated adhesive exhibited high glass transition temperature and there was little gap in peel strength before and after thermal treatment. Moreover, it was confirmed by rheological analysis that this adhesive can provide great bonding/debonding ability without distortion. We demonstrated the fabrication of a rectangular product using a 3D printing method using our acrylic adhesive as a build sheet. Mounting ability and workability were satisfactory and dimension deviation of the product was tiny. Because the product is easily detachable from the acrylic adhesive developed here than conventional build sheets, it is expected that this will provide work convenience to users who use the 3D printer.

• Journal of Korean Society of Forest Science
• /
• v.94 no.4 s.161
• /
• pp.243-251
• /
• 2005

This study was carried out to evaluate precipitation, geological and topographical factors from the landslide area occurred in Maeri, Sangdong-myeon, Gimhaesi, Gyeongsangnam-do. The landslide was affected by geo-topographical factors. Talus which is infiltrated easily by runoff was widely distributed in the landslide area. Concave areas on back- and toe-slope were built up colluvial materials and weathered soils. The colluvial materials were consisted of less weathered pebbles and stones (diameter: 10~100 cm) which are easily infiltrated during rainfall events. Also the landslide was mainly affected by an ascending of ground water table which is low in summit and high in toe-slope due to geo-topographical characteristics of the landslide area. The most important reason of the landslide was a lacking of drainage system of ground water despite the high infiltration rates of ground water in talus area during rainfall events.

• Land and Housing Review
• /
• v.2 no.3
• /
• pp.287-297
• /
• 2011

This paper presents the results of performance verification tests of the isolated flat plate apartment building with the laminated rubber bearings. The shaking table test is carried out in CABR(China Academy of Building Research) with two 1/10 scale isolation and non-isolation models under 4 excitation waves. The shaking table test is proceeding from x axis, y axis and x+y axis with different amplitude of acceleration values. The results show that, to non-isolated model, the natural vibration period is remarkably decreased and entered non-linear condition after moderate earthquake. Its accelerations become lager with increasing storey number and completely collapsed under large earthquake. The inter-storey shifts largely exceed the limit values of regulated displacement angles. But to isolated model, the natural vibration period of isolated modal is almost the same in all conditions and still in its elastic condition. The earthquake loading is greatly reduced and the accelerations of superstructure are greatly reduced. The inter-storey drifts are very small and can be neglected. The isolated model is in translational state and can be seen as a rigid whole. The displacements of isolation layer are in the allowable range. This experiment demonstrates that the seismic isolation is very effective to mitigate the influence of earthquake on structures and it is possible to increase the serviceability due to decrease the floor acceleration. facilities from their good states that is superior to non-isolated structure.