• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.4
• /
• pp.812-818
• /
• 2003

This paper presents a developed outside rotor type induction motor for the fan. Nearly all of the induction motors consist of two parts, rotor and stator, and the position of rotor is generally inside of stator. However, the rotor of the developed induction motor is located outside of stator. It is believed that the outside rotor type induction motor is suitable for the fan due to its large inertia, that is, it is considered that the change of air flow rate resulting from input power or load fluctuation is reduced. In this paper, the two tests which are suitable to obtain the electrical parameters of the outside rotor type induction motor were described, then various parameters of outside rotor type induction motor were measured. These are the locked rotor test and no load test. By using these tests, it was possible to determine the parameters which are presented in the steady-state equivalent-circuit of the outside rotor type induction motor. Load test of induction motor was carried out using a dynamometer and the torque-speed curve was obtained. It is believed that the results of this paper can be used for the development of the outside rotor type induction motor.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.18-24
• /
• 2017

Appropriate selection of the starter is essential for successful starting of the gas-turbine engine. Thus, aerodynamic drag during starting phase should be analyzed to assess the feasibility of the starter. In this paper, aerodynamic drag is modeled based on the speed profile from the engine coast down test, and it is scaled with respect to the target engine by comparing the compressor load. Afterward, the govern equation of the starting phase is developed with the torque model of the starter, and the design scheme to select the feasible starter will be finally suggested. The proposed model of starting phase will be useful to perform a preliminary design of the starting system of the gas-turbine engine.

• Journal of Animal Environmental Science
• /
• v.11 no.1
• /
• pp.11-16
• /
• 2005

The round bale wrappers are generally used for rice straw after the harvesting of low land rice by combine harvester. In this situation, the bale wrappers should be well adapted under the travelling over raised borders and temporary ditches in soft soil of narrow rice fields. The study was conducted to improve the performance of bale wrapper through the new design for compact size, lowered gravity center and lowered power consumption. The prototype of round bale wrapper had been designed and assembled to tractor with three point hitch mounted. The machine type is one roll driving system with one roll for rotating and one roll for wrapping. The driving torque and work performance of the machines were measured and analysed. The torque requirement of the prototype and conventional type was 6kgf-m and 12kgf-m, respectively. The prototype shaved less friction resistance between bale driving roll and round bale. and the power requirement can also be reduced from 12kgf-m in the conventional to 6kgf-m in the prototype. The work efficiency of the new bale wrapper was $45\%$ higher than the conventional wrapper, and the working cost of the prototype can be reduced $17\%$ than that of the conventional.

• The Korean Journal of Pesticide Science
• /
• v.15 no.1
• /
• pp.61-67
• /
• 2011

In 2010, two-spotted spider mite, Tetranychus urticae was collected from the rose greenhouse and apple orchards in Cheongju (CJ), Chungju (CUJ)-1, CUJ-2, Kangjin (KJ), Yesan (YS), and Yeongju (YJ). Among them, KJ and YS strain showed high resistance to bifenazate of 964.5- and 1l30-fold, respectively. The other strains showed low resistance to bifenazate. By analyzing the mitochondrial cytochrome b (cytb) sequence, G126S point mutation was detected in KJ and YS strain. Thus, G126S point mutation in the mitochondrial cytb was available molecular detection marker for selection of bifenazate resistant T. urticae. Two molecular detection methods, quantitative sequencing (QS) and PCR amplification of specific alleles (PASA) were well detected specific G126S point mutation. Therefore, these methods can be used to monitor the resistance allele in field population of T. urticae and bifenazate resistance management strategy.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.1
• /
• pp.139-148
• /
• 2009

D. W. HAN. Y. R. AHN., N. J. LEE and E. J. LEE. Effects of Combined Restistance Training Program of Concentric and Eccentric Contraction Using Theraband on Shoulder Rotation Torque Max and Peak Power. Korean Joumal of Sport Biomechanics, Vol. 19, No. 1, pp. 139-148, 2009. The purpose of this study was to find out that combined concentric with eccentric resistance training program using Thera-Band was more effective than only concentric resistance training program on shoulder rotation torque max and peak power. 30 female students were randomly assigned to 3 equal group; concentric and eccentric, concentric, non training group. Subjects were tested in concentric and eccentric torque max and peak power of internal and external rotation using a CON-TERX isokinetic dynamometer. Subjects in training group participated in their regular five times a week for 4 weeks. After exercise, in concentric and eccentric training group, concentric and eccentric torque max, and peak power of internal rotator at 60 deg/sec were increased significantly. concentric peak power at 120 deg/sec were increased significantly. In concentric training group, only concentric peak power of internal rotator at 60 and 120 deg/sec was increased. In conclusion, we found out that combined concentric with eccentric resistance training program using Thera-Band was more effective than only concentric resistance training program on shoulder rotation torque max and peak power.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.9
• /
• pp.552-561
• /
• 2004

This paper is concerned with a new speed sensorless induction motor scheme which can be successfully applied to at any speed including even zero speed. The proposed method is robust against rotor resistance variations. In addition, simultaneous on-line estimations of speed and rotor resistance are realized based on a feedforward type torque control approach. The rotor flux with a low frequency sinusoidal waveform has been utilized to help the simultaneous estimation for both speed and rotor resistance. The control scheme has no current minor loop to determine voltage references. Since the proposed estimation does not depend on any derivative terms of currents and stator voltages, it offers a good performance at extremely low speed region for sensorless induction motor. Furthermore, the proposed control is simply using motor parameters and stator currents without determining any PI gains for current feedback and any signal injection for the rotor resistance estimation. Finally, both simulation and experimental results are given to show the effectiveness of this method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.4
• /
• pp.128-135
• /
• 1998

In the high speed range for salient type synchronous reluctance motor, the effect of iron loss can not be negligible. In this paper, under he assumption that stator iron loss is generated from the equivalent eddy current in the stator, we derive the voltage equations including iron loss from the model that is added the equivalent iron loss in the equivalent inductance in series. The variation of iron loss is dependent on the increase of the operating frequency change for he worse a performance of the vector control system. As there is cross coupling between the d and q axes, it is hard to apply the vector control to the proposed model. Hence, we propose a decoupling current controller for including the effects of iron loss, And we show that the proposed vector control scheme achieves the desired performances through simulation results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1393-1401
• /
• 2010

In this experimental study, we have examined the correlation between a human carpal motion and a surface electromyogram. The carpal motion patterns have been identified and the main muscles involved in the carpal motion have been determined by investigating the anatomical structure of a carpal. The torque acting against the carpal motion has been applied by using a device for carpal rehabilitation training, and the surface electromyogram signal corresponding to the torque at the main muscles has been measured. The root-mean-square (RMS) magnitude of the surface electromyogram signal has been calculated and used to analyze the correlation between the surface electromyogram signal and carpal motion. The experimental results have proved that for carpal torque values below $0.1\;N{\cdot}m$, the RMS magnitude of the surface electromyogram signal is linearly proportional to the carpal torque magnitude and that the carpal torque magnitude is linearly proportional to the cross-sectional area of the carpal muscles. Further, the analysis of the contribution of each muscle to the carpal motion has shown that the contribution of the most dominant muscle is consistently 60%. These three results can be applied to develop more sophisticated devices or robots for carpal rehabilitation training.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.114-118
• /
• 2009

이 논문에서는 울돌목 시험조류발전소에 구축 중인 구조건전성 감시시스템의 계획, 설치 및 활용에 대하여 소개하였다. 현재 시험조류발전소에 설치된 센서로는 전기저항식 변형률계, 광섬유 FBG(Fiber Bragg Grating) 센서, 압전형 MFC(Macro Fiber Composite) 센서, 2축 경사계, 서보형 가속도계 등과 같은 지지구조물의 구조거동을 감시하기 위한 센서와 토크 센서, RPM 센서 등 발전 계통에 대한 감시를 위한 센서, 그리고 H-ADCP(Horizontal Acoustic Doppler Current Profiler)와 같은 외력조건에 대한 계측 장비 등이 있다. 센서 설치 후 현재까지 부분적으로 계측된 자료를 소개하고, 향후 건전성 감시시스템 개선 계획을 소개하였다.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.412-414
• /
• 1996

The rotor resistance variation has a large effect on the field oriented control system of induction machine. In this paper, the adaptation technique based on MRAC is used to identify the rotor resistance variation. The criterion function used in the adaptation algorithm is the error function of the two reactive powers of the induction motor. The one is obtained from the voltages and the currents of the stator of the induction motor. And the other is estimated from the rotor flux and stator current. We simulated this control system operated by field oriented control and assured the robustness of the induction motor control system against the rotor resistence variation.