• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.61-66
• /
• 2005

In order to make submicron cell for spin-injection device, lift-off method using Pt stencil and wet etching was chosen. This approach allows batch fabrication of stencil substrate with electron-beam lithography. It simplifies the process between magnetic film stack deposition and final device testing, thus enabling rapid turnaround in sample fabrication. Submicron junctions with size of $200nm{\times}300nm$ and $500nm{\times}500nm$ 500 nm and pseudo spin valve structure of $CoFe(30{\AA})/Cu(100{\AA})/CoFe(120{\AA}$) was deposited into the nanojunctions. MR ratio was 0.8 and $1.1{\%}$, respectively and spin transfer effect was confirmed with critical current of $7.65{\times}10^7A/cm^2$.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.73-77
• /
• 2002

Characteristics of Cu/Si/Cu ohmic contacts to n-type 4H-SiC were investigated systematically. The ohmic contacts were formed by rf sputtering of multi layer Cu/Si/Cu sputtered sequentially. The annealings were peformed With 2-Step using RTP in vacuum ambient. The specific contact resistivity($\rho$c), sheet resistance(Rs), contact resistance(Rc), transfer length(L$_{T}$) were calculated from resistance(R$_{T}$) versus contact spacing(d) measurements obtained from TLM(transmission line method) structure. Best results were obtained for a sample annealed at vacuum as $\rho$c = 1.0x10$^{-6}$ $\Omega$$\textrm{cm}^2$, Rc = 2$\Omega$ and L$_{T}$ = 1${\mu}{\textrm}{m}$. The physical properties of contacts were examined using XRO and AES. The results showed that copper silicide was formed on SiC and Cu was migrated into SiC.o SiC.

• Membrane Journal
• /
• v.13 no.2
• /
• pp.88-100
• /
• 2003

A change of filtrate flux in Taylor vortex flow filtration was investigated experimentally by rotating speed of inner cellulose ester membrane cylinder (average pore size: 1.2 ${\mu}m$), slurry concentration, and particle size. The filtrate flux was a direct proportion relation with TMP, but an inverse relation with resistances. A change of cake resistance with time was examined by rotating speed, slurry concentration, and particle size. Initial resistance increased dramatically as raising slurry concentration, and the pseudo-steady state was maintained at high resistance value. However, times to reach the pseudo-steady state did not depend on slurry concentration. The resistance was larger as smaller particle size, because possibility of pore blocking inside membrane could be higher and shear effect should be lower as smaller particle size. A model equation suggested in this study was composed of particle deposition and removal terms, and could confirm well experimental data using average values of experimental coefficients.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.656-665
• /
• 2021

In this study, trim tabs were attached to end of stern hull of a small high-speed vessel of length approximately 10 m and Froude number 1.0 to improve resistance performance and passenger comfort. Before computational fluid dynamics (CFD) simulations to assess the performance according to various geometries of the trim tab, the scale effect had been found through a previous study, so full-scale simulations were performed. The trim tab chord length was set to 0.5 %, 1.0 % and 1.5 % of L_PP, and its angle to base line was varied in intervals of 5°. It decreased trim by stern and flotation: the greater the angle and length, the greater was the effect. Then it had pressure resistance decreased and shear resistance increased, and reduction ratio of total resistance varied accordingly. The results of this study indicated that the resistance performance was improved about 27 % at optimal running attitude that was the trim by stern about 1.5°.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.4
• /
• pp.44-49
• /
• 2003

This study was carried out to evaluate the weathering durability of waterborne preservative (AAC, ACQ, CCA, CuAz) treated Japanese red pine (Pinus densiflora S. et Z.) sapwood samples by accelerated weathering, and to find out the factor of stability. When considered the color changes, weight losses, surface degradation, and microstructure changes due to weathering, ACQ-, CCA-, and CuAz-treated samples were durable against weathering; the weathering durability of AAC-treated samples was poor and similar to untreated controls. The lignin content in aqueous extracts collected from ACQ-, CCA-, and CuAz-treated samples during weathering was lower than that from untreated and AAC-treated ones. From these findings, we might concluded that weathering durability of ACQ-, CCA-, and CuAz-treated samples was enhanced by the fixation of preservative component(s) onto the lignin structure, which is very susceptible to weathering.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.4
• /
• pp.59-68
• /
• 2010

Piping, a common form of internal embankment erosion, is caused by progressive movement of soil particles through an embankment. The phenomenon commonly occurs with precursory signs of development of fractures in dam structures, but also occurs without any noticeable signs in dams that showed satisfactory dam performance for several years, due to dissolution of soluble material in an embankment. While piping accounts for nearly 50% of the causes for dam failure, few studies have been made for systematic evaluation of the phenomenon. In this study, we attempted to monitor the changes in electrical resistivities of fill-dam material while a saddle dam is dismantled for the construction of emergency spillways of Daechung dam. Two artificial subhorizontal boreholes were drilled into the embankment structure to simulate piping along the two artificial flow channels. Monitoring of changes in electrical resistivity showed an increase in resistivity values during piping. Thus, the investigation of resistivity over time could be an effective method for piping prediction.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.2
• /
• pp.181-192
• /
• 2001

이 논문은 샌드위치식 강-콘크리트 복합구조체에서 상하 강판과 격벽으로 구성되는 셀의 형상비가 거동과 성능에 미치는 영향을 다루었다. 이 구조체에서 셀 형상비는 하중전달 메카니즘과 하중분배능력을 변화시킨다. 따라서 셀 형상비에 따라 부재의 응력수준과 하중저항능력이 변화한다. 이 연구에서는 셀 형상비가 이 구조체의 거동과 성능에 미치는 영향을 규명하기 위해, 두 종류의 샌드위치식 복합구조체에 대해 다양한 셀 형상비를 설정하여 비선형 구조해석을 수행하였다. 해석결과로부터 셀 형상비에 따른 하중전달 메카니즘과 부채 응력에서의 차이점을 도출하였으며, 이들 차이점을 바탕으로 셀 형상비가 전단성능, 휨성능, 하중저항성능에 미치는 영향을 분석하였고, 파괴모드와 연성에 미치는 영향에 대해서도 간략히 언급하였다. 연구결과, 셀 형상비가 증가함에 따라 하부 강판과 콘크리트의 응력수준이 낮아지는 결과를 나타내었다. 이것은 각 부재의 유효휨강성과 유효전단강성 증가를 나타내며, 따라서 구조체의 하중저항성능도 향상되는 것으로 판단된다. 특히 셀 형상비의 증가에 따른 성능향상에서 전단성능이 휨성능에 비해 더 큰 효과를 나타내며, 이러한 차이는 파괴모드와 연성에도 영향을 미칠 것으로 판단된다. 즉, 셀 형상비가 증가함에 따라 구조물의 거동 및 파괴모드는 점차적으로 전단에서 휨으로 변화하고, 이에 따라 구조물의 연성도 점차적으로 향상될 것으로 판단된다.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.243-249
• /
• 1999

A magnetic field sensor is fabricated with superconducting ceramics of Y-Ba-Cu-O system. The prepared material shows the superconductivity at about 95K. The sensor at liquid nitrogen temperature shows the increase in electrical resistance by applying magnetic field. Actually, the voltage drop across the sensor is changed from zero to a value. more than $100{\mu}V$ by the applied magnetic field. The change in electrical resistance depends on magnetic field. The sensitivity of this sensor is 2.9 ohm/T. The sensing limit is about $1.5{\times}10^{-5}T(=1.5{\times}10^{-1}G)$. The increase in electrical resistance by the magnetic field is ascribed to a modification of the Josephson junctions due to the penetrating magnetic flux into the superconducting material.

• Journal of the Microelectronics and Packaging Society
• /
• v.1 no.2
• /
• pp.125-134
• /
• 1994

저항범위가 다른 두종류의 Ru계 후막저항계(1Kohm/sq. 100kohm/sq.)를 선택하여 도전상의 상전이 기구를 반응조건을 변화시켜 연구하였다. 저저항체의 경우 도전상으로는 RuO2였으며 700-100$0^{\circ}C$에서 1시간 반응한 경우 반응온도에 따른 구성상의 변화는 없었다 반응온도 90$0^{\circ}C$에서 반응시간이 경과함에 따라 도전상은 RuO2가 Glass의 구성성분인 Pb와 반응하여 Rb2(Ru1.69 Pb0.31)O6.5로 변하고 시간이 36시간 경과한 후에는 도전상이 Pb4Al2Si2O10인 결정으로 둘러 쌓이는 반응인 peritectic reaction이 일어났다. 고전항체의 경 우 도전상으로는 Pb2(Ru1.69 Pb0.31)O6.5로 변하고 시간이 36시간 경과한 후에는 더전상이 Pb4Al2Si2O10인 결정으로 둘러쌓이는 반응인 peritectic reaction 이 일어났다. 고저항체의 경 우 도전상으로는 Pb2(Ru1.69 Pb0.31)O6.5인 pyrochrole 상이였다. 100$0^{\circ}C$에서 1시간 반응시킬 경 우 도전상이 RuO2로 변하였다. 반응온도를 90$0^{\circ}C$로 하고 반응시간을 변화시키면 도전상인 Pb2(Ru1.69 Pb0.31)O6.5가 (Ru1.69Pb0.31)O4x로 변하면서 공존하였다.

• Korean Journal of Materials Research
• /
• v.6 no.9
• /
• pp.937-942
• /
• 1996

박막 공정 및 마이크로머시닝(micromachining)기술에 의해 제작되는 마이크로 가스 센서는 고온 동작이 필수불가결하며 이 때 안정된 출력을 얻기 위해서 센서 저항 변화에 영향을 줄 수 있는 응집화 현상이 발생하지 말아야 한다. 본 연구에서는 고온 동작시 응집화의 구동력으로 작용하는 여러 요소중의 하나인 응력(stress)을 줄이기 위해서 인가 전력 밀도, 기판온도, 증착 압력 등을 증착 변수로 하여 증착 조건이 (AI, SI)1-xOx박막과 Pt 박막의 제반 물성 및 응력변화에 미치는 영향에 대하여 연구하였다. (AI, SI)1-xOx박막의 증착 속도와 굴절율 값은 O2분압과 기판 온도가 증가할수록 감소하였으며 응력은 O2분압이 증가함에 따라 인장에서 압축으로 전환된 후 증가하였다. Pt 박막의 경우, 인가 전력이 증가할수록 공정 압력이 감소할수록, 기판 온도가 감소할수록 증착 속도는 증가하였으며 전기 비저항은 감소하였다. Pt 박막의 응력은 인가 전력이 증가할수록, 공정 압력이 증가할수록, 기판 온도가 증가할수록 압축에서 인장의 방향으로 전환된 후 증가하였으며 박막의 전기비저항 및 증착속도에 크게 의존하는 것으로 분석되었다.