• Resources Recycling
• /
• v.9 no.6
• /
• pp.23-30
• /
• 2000

Since most of the waste plastics are incinerated and landfilled for the plastic treatment, the environmental friendly processes must be introduced. The plastic utilization of plastic to the blast furnace as a substitutional fuel was developed as a useful recycling method of waste plastics, and commercialized in several ironmaking company in Europe and Japan. Present study was carried out to understand the effect of plastic injection on blast furnace process continuously by using the foundry blast furnace in POSCO. The coke replacement ratio turned out to be 0.98 with the waste plastic injection up to 13.8 kg/thm of injection rate, and there were no significant effect of the kinds of injection plastics on the replacement ratio in this test operation. The permeability in the furnace became worse and the heat load in the lower part of blast furnace was increased with increasing the injection rate of waste plastics. As the rate of plastic injection were increased, the top gas utilization and shaft efficiency were also decreased from the Rist diagram analysis.

• Resources Recycling
• /
• v.30 no.1
• /
• pp.35-43
• /
• 2021

In this study, Na2SO4 and KCl reagents were used to synthesize K2SO4 as a basic study for recycling byproducts generated during the manufacture of steel and cement. The mole ratio of Na2SO4 to KCl, the saturation of the solution, and the stirring temperature were controlled to derive the optimal manufacturing conditions. The microstructure and crystallinity of the materials prepared were evaluated using scanning electron microscopy and X-ray diffraction analysis. Pure K2SO4 was obtained when the mole ratio of Na2SO4 to KCl was 1:6-18, the saturation of the solution was less than 160%, and the stirring temperature was 20℃, 50℃. The optimal manufacturing conditions to maximize the crystallinity and yield of K2SO4 while minimizing the energy consumption were 1:6 mole ratio of Na2SO4 to KCl, 140% saturation of the solution, and 20℃ stirring temperature.

• Resources Recycling
• /
• v.20 no.6
• /
• pp.43-49
• /
• 2011

This study calculated the three indices of Korea's resource productivity (and raw material productivity), material circulation rate and decoupling factor to evaluate the sustainability of domestic economic activities and resource consumption and examine the extent of dematerialization. Korea's resource productivity improved 22% from 1.32 million KRW/ton in 2000 to 1.61 million KRW/ton in 2007, with the annual average growth of resource productivity during the period standing at 2.88%. Raw material inputs accounted for 73-76% of domestic material consumption (DMC); raw material productivity for the year 2007 was 2.11 million KRW/ton, growing 3% on annual average from 2000 through 2007. The wastes released are circulated into the economic system through recycling and energization. Korea's material circulation went up from 10.9% in 2000 to 15.6% in 2007, growing by an annual average of 5.3% during the period. The rate of change in year-on-year growth, however, was found to be on the gradual decrease. This study also showed that Korea's economic activities were decoupled with its resource consumption as the country heads toward dematerialization through sustainable resource management.

• Korean Journal of Ichthyology
• /
• v.29 no.1
• /
• pp.41-51
• /
• 2017

To understand the application in farm for the fish aquaculture, we investigated biological and pathological traits on red sea bream Pagrus major which were reared in each copper-alloy net cage and the synthetic fiber net cage for 9 months. Two groups of cage were made and set in Yokji-eup, Tongyoung, Gyeongsangnam-do in size of 25 m in diameter and 10 m of depth. Survival rate of the red sea bream in the rearing copper-alloy net cage and synthetic fiber cage showed 99.75% and 99.70% respectively, there was no significant difference. Daily weight growth rate in each net was shown to 2.13 g/day and 1.65 g/day. Health analysis by blood composition analysis showed a favorable result in the copper-alloy net cage rather than in the synthetic fiber net. Bioaccumulation of heavy metal such as Cu and Zn especially in gonad was higher than other organ. Bioaccumulation of Cu and Zn in the muscle was lower compared to the permitted standard for food safety. Pathogenic infection test discovered Microcotyle tai for parasite, V. alginolyticus and other five species for bacteria. But there was a little bit difference of bacteria infection in copper-alloy net cage and copper-alloy net cage is expected to be has antibacterial effect. Thus, copper-alloy net cage can be applied to farm considering its system stability, recycling, antibiosis and food safety.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.2
• /
• pp.237-243
• /
• 2019

Floating platforms made of PE (PolyEthylene) are often located in shallows of seas, rivers or lakes. They are widely used for marine pensions, marine pontoons, marine bridges, etc. These products are characterized by good flexibility, recyclability, chemical resistance and weatherability with corrosion resistance. Existing PE floating platforms have a simple structure in which one pipe is fastened to one bracket, but this has limited application, even if a user modifies the arrangement. Therefore, we developed a structure that allows buoyancy pipes of various sizes to be fastened to one bracket and verified the structural safety of the product using the finite element method. From the results of structural analysis for buoyancy pipes of different diameters, the maximum stress ratio was 0.78 compared with allowable criteria of 1.0, which represented sufficient safety for a model with 500 mm diameter pipes. Based on the results of this study, further research to evaluate the structural safety of various floating platforms can be carried out in the further; it will also be necessary to establish related evaluation criteria.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.12
• /
• pp.1095-1104
• /
• 2009

The objective of this research was to evaluate the feasibility of using oyster-shell and eggshell wastes for the stabilization of arsenic-contaminated soil. Artificial As(V) contaminated soil was mixed with 0~5% oyster-shell and eggshell wastes and each sample was incubated for 30 days in a controlled environment. The efficiency of each treatment was evaluated using various single extractants (1 N HCl, 0.1 N NaOH and 0.5 N $H_2SO_4$). The concentration of As(V) was reduced by 10% upon a 5% oyster-shell or eggshell waste treatments based on the Korea Standard Test method (1 N HCl extraction). Analogous trends were observed in the 0.1 N NaOH or 0.5 N $H_2SO_4$ extractions. In addition, the oyster-shell and eggshell waste treatments increased the pH of each soil from 6.54 (Control) to 7.62~7.94. The exchangeable Ca in each soil also sharply increased from 6.87 cmol(+)/kg (Control) to 12.77~20.18 cmol(+)/kg. Further research is needed to increase the effectiveness of the oyster-shell and eggshell waste for the stabilization of As(V) in the contaminated soil.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.1
• /
• pp.33-40
• /
• 2024

The volume of shells, a prominent form of marine waste, is steadily increasing each year. However, a significant portion of these shells is either discarded or left near coastlines, posing environmental and social concerns. Utilizing shells as a substitute for traditional aggregates presents a potential solution, especially considering the diminishing availability of natural aggregates. This approach could effectively reduce transportation logistics costs, thereby promoting resource recycling. In this study, we explore the feasibility of employing wasted shell aggregates in 3D concrete printing technology for marine structures. Despite the advantages, it is observed that 3D printing concrete with wasted shells as aggregates results in lower strength compared to ordinary concrete, attributed to pores at the interface of shells and cement paste. Microstructure characterization becomes essential for evaluating mechanical properties. We conduct an analysis of the mechanical properties and microstructure of 3D printing concrete specimens incorporating wasted shells. Additionally, a mix design is proposed, taking into account flowability, extrudability, and buildability. To assess mechanical properties, compression and bonding strength specimens are fabricated using a 3D printer, and subsequent strength tests are conducted. Microstructure characteristics are analyzed through scanning electron microscope tests, providing high-resolution images. A histogram-based segmentation method is applied to segment pores, and porosity is compared based on the type of wasted shell. Pore characteristics are quantified using a probability function, establishing a correlation between the mechanical properties and microstructure characteristics of the specimens according to the type of wasted shell.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.1
• /
• pp.26-32
• /
• 2020

Concrete recycling is becoming mandatory rather selective due to depletion of constructional materials and increase of concrete waste. Studies on recycling concrete are conducted in various point of view for long time. However, standard or guideline of many countries for the application of recycled aggregate concrete(RAC) has restrictions such as low replacement rate of coarse aggregate and no fine aggregate allowed due to inferior material properties of recycled aggregate. This study intends to figure out the feasibility of casting natural aggregate concrete(NAC) and RAC separately in a structural member. In making RAC, replacement rate of coarse aggregate was 50, 100% in RAC and treatment of interface of two concretes is introduced. RAC treatment of recycled aggregate or inclusion of additives was not done as it can increase embodied energy of concrete work. Double-shear test with uniformly distributed loading was adopted to evaluate shear strength at the interface of two concretes. After curing it was hard to distinguish interface of two concretes. Experimental result revealed that specimen with higher replacement rate showed higher shear-to-compressive strength ratio, which is possibly attributed to coarse aggregate size and roughness of sheared section. Further study on the effect of various parameters is required and subsequent research activity is on-going.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.79-86
• /
• 2010

Cold in-place recycling (CIR) using emulsified asphalt or foamed asphalt has become a more common practice in rehabilitating the existing asphalt pavement due to its cost effectiveness and the conservation of paving materials. As CIR continues to evolve, the engineered emulsified asphalt was developed to improve the field performances such as coating, raveling, retained stability value and curing time. The main objective of this research is to compare the laboratory responses of the engineered emulsified asphalt (CIR-EE) mixtures against the foamed asphalt (CIR-foam) mixtures using the reclaimed asphalt pavement (RAP)materials collected from the CIR project on U.S. 20 Highway in Iowa. Based on the visual observation of laboratory specimens, the engineered emulsified asphalt coated the RAP materials better than the foamed asphalt because the foamed asphalt is to create a mastic mixture structure rather than coating RAP materials. Given the same compaction effort, CIR-EE specimens exhibited lesser density than CIR-foam specimens. Both Marshall stability and indirect tensile strength of CIR-EE specimens were about same as those of CIR-foam specimens. However, Marshall stability and indirect tensile strength of the vacuum-saturated wet specimens of CIR-EE mixtures were higher than those of CIR-foam mixtures. After four hours of curing in the room temperature, the CIR-EE specimens showed less raveling than the CIR-foam specimens. On the basis of test results, it can be concluded that the CIR-EE mixtures is less susceptible to moisture and more raveling resistant than CIR-foam mixtures.

• Journal of Korea Port Economic Association
• /
• v.24 no.1
• /
• pp.61-83
• /
• 2008

The meaning of "added value" refers to the contribution of the factors of production, i.e., land, labor, and capital goods, to raising the value of a product and corresponds to the incomes received by the owners of these factors. The importance of added value in service industry has been recognized as one of the critical factors to economic growth, even in logistics industry. But, it is hard to find out the previous studies providing a clear definition and framework for designing and analyzing the performance of Value Added Logistics(VAL). The purpose of this study is to define the meaning of extended VAL that extensively includes activities initiating and operating the reverse logistics under the closed-loop logistic scheme, and to suggest the framework that describes the partnerships among participants involving in operating the value added logistics. Also, in this paper, we emphasize on the need for investigation of added value logistics definition and framework based on previous academic studies, and examine various value added logistics service activities of current leading 3PL companies across the world. Finally, we suggest the analytic framework for value added logistics throughout closed-loop logistics.