• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.151-156
• /
• 2001

Experimental frictional and wear characteristics of silicon graphite materials is studied in this paper. Those specimens are lubricated with high temperature and highly pressurized water to simulate the same operating condition for the journal bearing and the thrust bearing on the main coolant pump bearing in the newly developing nuclear reactor named SMART(System-integrated Modular Advanced ReacTor). Operating condition of the bearings is realized by the tribometer and the autoclave. Friction coefficient and wear loss are analyzed to choose the best silicon graphite material. Pin on plate test specimens are used and coned disk springs are used to control the applied force on the specimens. Wear loss ana wear width are measured by a precision balance and a micrometer. The friction force is measured by the strain gauge which can be used under high temperature and high pressure. Three kinds of silicon graphite materials are examined and compared with each other, and each material shows similar but different results on frictional and wear characteristics.

• Explosives and Blasting
• /
• v.29 no.1
• /
• pp.41-47
• /
• 2011

In order to estimate blast damage zone and control rock fragmentation in blasting, it is important to obtain information regarding blast hole pressure. In this study, drop impact tests of acrylic, aluminium, steel sensors were performed to investigate the dynamic response characterizations of the sensors through the strain signals. As a result, the strain signals obtained from the steel sensors showed less sensitivity to impact force level and experienced small changes with various length of the sensors. The steel sensors were applied to measure the impact force of an electric detonator.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.6
• /
• pp.17-23
• /
• 2009

The survivability of the temporary nozzle extension for an accurate thrust measurement in a full-scaled combustor has been investigated through thermal analyses. The effects of nozzle extension materials and the thickness of thermal barrier coating (TBC) have been elucidated. It has been found that thermal survivability cannot be guaranteed without TBC. The maximum temperature of the nozzle extension decreased with increasing TBC thickness. For hot firing tests, the TBC is thought to be indispensable to the thermo-structural survivability of the nozzle extension made of steel.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.3
• /
• pp.291-294
• /
• 2011

The accident of Slip damage which arose between propeller boss and shaft will be a great problem of safety and economical due to the loss of propulsion power. In this study, the cause of slip damage on the large vessel was surveyed by meeting with officers of troubled ship, checking of drawings on the new built and surveyor report of adjuster company. Additionally, the material of propeller had been compression tested for confirming the impact strength. The result of this studies would be promote the design strength for contact force for keyless propeller, and futhermore reduce the accident of propeller slip between propeller boss and shaft.

• Transactions of the KSME C: Technology and Education
• /
• v.5 no.2
• /
• pp.81-87
• /
• 2017

315Fr compressor motor exceeds vibration specifications. To find the reason, first a modal impact test with free-free condition is done. Second a modal test with fixed condition is done. Thereafter the test results are compared with FEM simulation results. Using free-free condition modal impact test, FEM simulation conditions (boundary, mesh..) are modified. The motor has rolling motion around 120Hz. FEM simulation also shows same result. FEM simulation will be used to develop other series compressor motors. Using this, manufacturing test model and doing test will be useless.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.137-144
• /
• 2008

The stand-off errors due to the different separations between the sonde and the borehole wall were measured and analyzed in 4 physical borehole models located in Kangwon National University having different densities with cylindrical and half cylindrical PVC and/or acrylic casings. The analysis of the stand-off error data based on the "spine and ribs" technique suggests a well defined rib line for each model irrespectively of the types and thicknesses of the casing, and that the gradients of the ribs are proportional to the densities of the models. By using these characteristics successful density correction could be made for the plastic casings in NX sized boreholes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.697-702
• /
• 2007

The lubricational characteristics about friction and wear has an important effect on the material quality of surface. Therefore, in the case of automobile engine oil which is used under severe running condition, or therefore, the seizure and anti-scuffing is very important. We have studied the lubricational characteristics of auto engine oil with additives using Falex wear test machine. We have obtained the studied result is as fellows. In order to more improved the surface roughness characteristics adding the P(phosphate) as additives is excellent at a low temperature. Adding the ZnDTP and Ca-phenate is excellent on the anti-wear and extreme pressure properties at the high load. Moreover, when the ZnDTP and P are added, the temperature properties is excellent because the stability is maintained in a high temperature.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.3
• /
• pp.31-36
• /
• 2022

Recently, drones are being used in various fields, and drone technology is also developing. The risks of drones are increasing, then technology to detect drones is important. However, it is extremely difficult to detect and recognize drones due to the low level radar cross section of the commercial drones. In this paper, a signal processor structure that was mounted the miniaturized and light-weighted was designed. in order to process large amounts of data in real time, parallel processing was performed for each channel and an algorithm was applied to shorten the operation time in each step. As a test of verifing the detection performance through test, it was confirmed that the structure design works in real time.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.19 no.1
• /
• pp.11-19
• /
• 2023

Additive manufacturing technology, called as 3D printing, is one of fourth industrial revolution technologies that can drive innovation in the manufacturing process, and thus should be applied to nuclear industry for various purposes according to the manufacturing trend change in the future. In this paper, we performed tensile tests of 3D printed stainless steel 316L as-built specimens manufactured by two types of technology; DED (Directed Energy Deposition) and PBF (Powder Bed Fusion). Their mechanical properties (tensile strength, yield strength, elongation and reduction of area) were compared. As a result of comparison, the mechanical properties of the PBF specimens were slightly better than those of DED specimens. In the same additive type of specimens, the tensile and yield strength of specimens in the X and Y direction were higher than those in the Z direction, but the elongation and ROA were lower.

• Annual Conference of KIPS
• /
• 2007.11a
• /
• pp.874-877
• /
• 2007

최근 건설 산업이 고도화, 지능화됨에 따라 건설자재정보의 효율적인 관리방안으로 RFID 기술을 이용하려는 연구 및 적용 사례가 증가 하고 있다. RFID(Radio Frequency Identification)란 라디오 주파수를 이용한 무선인식 기법을 뜻하는 것으로 건설자재에 RFID Transponder(이하 태그)를 부착하여 생산, 유통, 설비 등 전 과정의 정보 추적 및 관리가 가능하다. 그러나 RFID 시스템 특성상 전자기장이 형성되는 철골자재나 수분이 포함된 콘크리트, 도료(안료) 등의 자재에서는 RFID 적용이 쉽지 않다. 또한, 현재 사용 중인 RFID 장비마저도 표준화 되어 있지 않고 사용 주파수 대역 또한 각각 다르기 때문에 건설자재에 적용하기위한 RFID 시스템의 표준화 및 규격화가 절실하다. 본 논문에서는 건설자재에 RFID를 적용하기 위한 표준화 방향을 제시하는 기초 연구로써 목재, 철재 빔, 도료(안료), 콘크리트, 배관자재(철/동/PE)에 Passive Type의 일반(Pager) 태그, 금속 태그, 액체형 태그를 부착 매립하여 125KHz, 13.56MHz, 900MHz의 주파수 대역과 자재 물성별 인식거리 및 인식률 시험을 진행하여 건설자재에 RFID를 적용하기위한 표준 주파수 대역 및 재질에 따른 적정 태그를 제시하고자 한다.