• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.665-669
• /
• 2007

This study investigates the temperature change and thermal conductivity for the braking disc of the railway vehicle due to the types of train and service conditions. The temperature change was measured by non-contact Infrared thermometers. Average temperature was measured between $79.32^{\circ}C$ and $104.46^{\circ}C$ due to types of train and service section. In the same service section, the surface temperatures of Saemaul train were higher than Mugungwha train; the reason might have been the average service speed of Saemaul train (83km/h) was higher than Mugungwha train (107km/h), and the weight was similar 39t (Mugungwha) and 39.3t (Saemaul). But the maximum surface temperature was measured on the Mugungwha train; however the difference was not too big with the maximum temperature of Saemaul train. Also, the disc surface temperatures were changed due to the material of lining; metal and non-asbestos, on the same train and the same service section. In addition. the thermal conductivity was tested the thermal conductivities were increased by the increasing of the temperature. The change is too big between $100^{\circ}C$ and $200^{\circ}C$. But each average value is small. and the mechanical property change is very low. As a result, we conclude that this disc is suitable for usage between $100^{\circ}C$ and $300^{\circ}C$.

• International Journal of Highway Engineering
• /
• v.9 no.2 s.32
• /
• pp.13-25
• /
• 2007

Viscosity, adhesion and cohesion of asphalt binder are very important characteristics in asphalt pavement. However, these characteristics can cause some problems such as inaccurate amount of asphalt mixture, reduction of asphalt content and loss of workability during asphalt pavement construction. Asphalt release agent has been used to solve these problems. Diesel oil and vegetable oil are generally used as an asphalt release agent in Korea. However, these agents have been criticized from environmental and binder integrity reasons. Therefore, this study evaluated the characteristics of asphalt release agents including diesel oil, vegetable oil and two emulsion type oils. From the study, it was found that the diesel oil resolved the binder within ten minutes and vegetable oil stripped the binder from mixture within one hour after contacting with asphalt mixture. And also, from the test for estimating the application cycle of asphalt release agent, it appears that diesel oil and vegetable oil should be applied to construction equipments every time in their uses. However, diesel oil and vegetable oil showed a good performance as a lubricant for detaching the asphalt mixtures from the truck bed.

• International Journal of Highway Engineering
• /
• v.16 no.3
• /
• pp.43-50
• /
• 2014

PURPOSES : The dynamic modulus can be determined by applying the various theories from the Impact Resonance Testing(IRT) Method. The objective of this paper is to determine the best theory to produce the dynamic modulus that has the lowest error as the dynamic modulus data obtained from these theories(Complex Wave equation Resonance Method related to either the transmissibility loss or not, Dynamic Stiffness Resonance Method) compared to the results for dynamic modulus determined by using the Universal Testing Machine. The ultimate object is to develop the predictive model for the dynamic modulus of a Linear Visco-Elastic specimen by using the Complex Wave equation Resonance Method(CWRM) came up for an existing study(S. O. Oyadiji; 1985) and the Optimization. METHODS : At the destructive test which uses the Universal Testing Machine, the dynamic modulus results along with the frequency can be used for determining the sigmoidal master curve function related to the reduced frequency by applying Time-Temperature Superposition Principle. RESULTS : The constant to be solved from Eq. (11) is a value of 14.13. The reduced dynamic modulus obtained from the IRT considering the loss factor related to the impact transmissibility has RMSE of 367.7MPa, MPE of 3.7%. When the predictive dynamic modulus model was applied to determine the master curve, the predictive model has RMSE of 583.5MPa, MPE of 3.5% compared to the destructive test results for the dynamic modulus. CONCLUSIONS : Because we considered that the results obtained from the destructive test had the most highest source credibility in this study, the dynamic modulus data obtained respectively from DSRM, CWRM were compared to the results obtained from the destructive test by using th IRT. At the result, the reduced dynamic modulus derived from DSRM has the most lowest error.

• Korean Journal of Plant Resources
• /
• v.31 no.1
• /
• pp.71-76
• /
• 2018

This study was conducted to investigate the effect of shoot twist on fruitfulness and fruit quality of 'Campbell Early' grapevine. Proper pruning and training are essential to produce a good yield of high-quality fruit and to maintain the balance between vegetative growth and fruiting. The most common problem in spur-pruned 'Campbell Early' cultivar is that vigorous buds has low fruitfulness and thereby the shoot become more vigorous the following spring because of lower crop load. Therefore, shoot twists in very vigorous 'Campbell Early' canes (above 10.0 mm) were performed on the third nodes and the $7^{th}$ nodes of each shoot at 7 days before bloom and full bloom, respectively. Sprouting date, blooming date were not significantly different among the treatments while, harvesting date was delayed approximately 3 days. However, number of berries per cluster, cluster weight and fruitfulness were significantly higher in the shoot twist treatment on the third nodes than the control that was topping alone. Combination treatments of shoot twist and topping had an additive effect on increasing cluster weight resulting in higher increase of yield by 12.1 ㎏ per vine. These results indicated that the shoot twist on very vigorous canes of 'Campbell Early' grapevine for well fruitfulness seemed to be very effective.

• The korean journal of orthodontics
• /
• v.31 no.4 s.87
• /
• pp.459-465
• /
• 2001

The purpose of this study was to evaluate the feasibility of the combined use of paste resin with sealant as an adhesive of the indirect bonding. The resin bases made of light-cured resin were bonded to the bovine incisors at a distance of 0.0, 0.2 or 0.4 mm using the sealant only or the mixture of sealant and paste resin. Bond strength of each group was measured using universal testing machine. The results were as follows : 1. The bond strength was reduced in both groups as the distance between enamel surface and resin base increased. 2. The bond strength showed no statistical difference between two groups in case the distance between enamel surface and resin base was 0.0 mm. 3. In case the distance between enamel surface and resin base was 0.2 or 0.4 mm, the sealant with paste resin group showed significantly higher bond strength than the sealant only group. The results of the present study indicate that the use of paste resin with sealant may be desirable as an adhesive in indirect bonding, particularly in case a gap is suspected between enamel surface and resin base.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.1
• /
• pp.44-50
• /
• 2013

E-glass fiber is the most widely used glass fiber for reinforced composite materials of aircrafts, automobiles and leisure equipments. But recently researches are being progressed to reduce boric oxide from 8 % to 0 (zero), as is called 'Boron free E-glass', because of increasing material cost, environmental problem, and improving chemical resistance and mechanical properties of E-glass fiber. In this study, we fabricated the bulk glass and fiber glass of 'Boron free E-glass (BF) compositions', and characterized thermal properties and optical properties. 'Boron free E-glass (BF)' was obtained by the melting of mixed batch materials at $1550^{\circ}C$ for 2 hrs with different $Al_2O_3$ compositions 5~10 %. We obtained transparent clear glass with high visible light transmittance value of 81~86 %, and low thermal expansion coefficient of $4.2{\sim}4.9{\times}10^{-6}/^{\circ}C$ and softening point of $907{\sim}928^{\circ}C$. For the chemical resistance test of 'BF' fiber samples, we identified that the higher alumina contents gives the better corrosion resistance of glass fiber.

• Korean journal of applied entomology
• /
• v.13 no.2 s.19
• /
• pp.93-97
• /
• 1974

This paper describes experiments made to develop a technique for marking insects and get the informations for ecological studies as a means of tagging flies with radioactive phosphorus, and also to learn the effect on the subsequent generation of flies. Tests were conducted with house flies, Musca domestica L. emerged front the larvae that had reared in a media containing various concentrations of P-32. Radioactivity of the flies was measured with end-window type $(2mg/cm^2)$ Geiger-Muller counter and proportional counter made by Aloka. In following the daily increases in counting rates by 6-day-old larvae it was apparent the larvae in the starting media containing the higher concentrations of P-32 were showing high counting rates. It was found that about 13.2 per cent of the radioactive material remained in the empty puparia after the flies emerged. Radioactivity of the emerged flies decreased gradually and the biological halflife of phosphorus-32 was approximately 6.14 days with considerable variation. A significant amount of P-32 were detected in the abdominal and thoracic sections as compared with other parts of adult. The activity of phosphorus·32 in eggs and larvae produced by adults reared in medium containing 0.2 microcurie or more of P-32 per gram were readily detected with Geiger-Mi·lier counter. On the other hand, the radioactivity of eggs and larvae produced by the treated males crossed with untreated normal females could be only detected in the medium containing more of 2.0 microcurie with G.M. counter. There was no apparent damage to the flies at dosages as high as 0.5 microcurie per gram of medium. For field studies a concentration of 0.5 microcurie of P-32 per gram of artificial medium appears to give adequate labeling for positive identification of flies and their egg masses.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.77-81
• /
• 2020

Commercialization of flexible OLED displays, such as rollable and foldable displays, has attracted tremendous interest in next-generation display markets. However, during bending deformation, cracking and delamination of thin films in the flexible display panels are the critical bottleneck for the commercialization. Therefore, measuring mechanical properties of the fragile thin films in the flexible display panels is essential to prevent mechanical failures of the devices. In this study, tensile properties of the metal and ceramic nano-thin films were quantitatively measured by using a direct tensile testing method on the water surface. Elastic modulus, tensile strength, and elongation of the sputtered Mo, MoTi thin films, and PECVD deposited SiN_x thin films were successfully measured. As a result, the tensile properties were varied depending on the deposition conditions and the film thickness. The measured tensile property values can be applied to stress analysis modeling for mechanically robust flexible displays.

• Computational Structural Engineering
• /
• v.8 no.4
• /
• pp.87-97
• /
• 1995

For the same configuration of two-dimensional finite element models, 6-node element exhibits stiffer bending stiffness than 8-node element. This is true in the relation between 16-node element and 20-node element for three-dimensional model. This stiffening phenomenon comes from the elimination of several mid nodes from full-node elements. Therefore, this may be called 'relative stiffness stiffening phenomenon'. It seems that there are a couple of ways to correct the stiffening effect, however, we could find only one effective method-the method of modification of Gauss sampling points-which passes the patch test and does not alter other kinds of stiffness, such as extensional stiffness. The quantity of modification is a function of Poisson's ratios of the constituent materials. We could obtain two modification equations, one for plane stress case and the other for plane strain case. This method can be extended to 3-dimensional solid elements. Except the exact plane strain cases, most 3-dimensional plates could be modeled successfully with 16-node element modified by the equation for the plane stress case. The effectiveness of the modification method is checked by applying it to several examples with excellent improvements. In numerical examples, beams with various boundary conditions are subjected to static and time-dependent loads. Free and forced motion analyses of beams and plates are also tested. The beam and plate may be composed of isotropic multilayers as well as a single layer.

• Journal of the Korea Concrete Institute
• /
• v.28 no.2
• /
• pp.197-204
• /
• 2016

Concrete walls of neutron generating facilities such as fusion reactors and fission reactors become radioactive by neutron irradiation. Both low-activation and neutron shielding are a critical concern at the dismantling stage after the shutdown of facilities with a requirement of radioactive waste management. To tackle this, two types of additives were investigated in fabricating mortar specimens: synthetic high polymers and boron carbide. It is well known that a hydrogen atom is effective in neutron shielding by an elastic scattering because its mass is almost the same as that of the neutron. And boron is an effective neutron absorber with a big neutron absorption cross section. In this study, the effect of the type, shape, and size of polymers were investigated as well as that of boron carbide. Total 16 mix designs were prepared to reveal the effect of polymers on mechanical properties and neutron shielding performance. The neutron does equivalent of polymers-based mortar for fast neutrons decreased by 36 %, and the count rate of boron carbide-based mortar with regard to thermal neutrons decreased by 90 % compared to conventional mortar. These results showed that a combination of polymers and boron carbide compounds has potential to reduce the thickness of neutron shields as well as radioactive waste from reactors.