• Composites Research
• /
• v.35 no.6
• /
• pp.463-468
• /
• 2022

The high porosity of the infill pattern of carbon chopped fiber-reinforced Nylon composite structures fabricated by the fused filament fabrication (FFF) type 3D printers determines the mechanical performance of the printed structures. This study experimentally evaluated the mechanical performance of Onyx composite specimens fabricated with a rectangular infill structure under the hot-pressing condition to improve the mechanical properties by reducing the porosity of the infill pattern of the printed structure, and evaluated the best mechanical performance. The hot-pressing conditions (145℃, 4 MPa, 12 min) that induce the most appropriate mechanical properties were found. As a result of microscopic observation, it was confirmed that the infill porosity of the composite specimens subjected to post hot-pressing treatment was effectively reduced. In order to confirm the mechanical performance of the post-treated specimen, a tensile test and a three-point bending test were performed with a control specimen without post-treatment and a specimen printed with the same density and dimensions after post-treatment to evaluate the mechanical properties. As a result of comparison, it was confirmed that the mechanical properties were effectively improved when the post-treatment of hot-pressing was performed.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.12
• /
• pp.5-17
• /
• 2010

Coarse granular material is used as important fill material in most of large embankments such as railway, road, dam and so on. Therefore, the accurate design parameters of the coarse granular material are necessarily required in design and construction. The behavior of the coarse granular material was not well understood because of the lack of large testing equipment capable of coarse granular material. A large triaxial testing system was developed in this research, capable of large specimens of 500 mm, 300 mm and 150 mm in diameter. In the new large triaxial testing system, the load cell is installed inside the triaxial cell and axial displacement is measured locally on a specimen in order to improve control and measurement in small strain level. Urethane specimens of 300 mm and 50 mm in diameter were prepared. The large triaxial tests were performed on the 300 mm diameter urethane specimens while RC/TS and impact echo tests on the 50 mm diameter urethane specimens to verify this testing system. In this verification test results, we could ascertain the reasonable test results of the KRRI large triaxial testing system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.6
• /
• pp.848-859
• /
• 2004

Mechanical testing methods to determine the material constants for large deformation nonlinear finite element analysis were demonstrated for natural rubber. Uniaxial tension, uniaxial compression, equi-biaxial tension and pure shear tests of rubber specimens are performed to achieve the stress-strain curves. The stress-strain curves are obtained after between 5 and 10 cycles to consider the Mullins effect. Mooney and Ogden strain-energy density functions, which are typical form of the hyperelastic material, are determined and compared with each other. The material constants using only uniaxial tension data are about 20% higher than those obtained by any other test data set. The experimental equations of shear elastic modulus on the hardness and maximum strain are presented using multiple regression method. Large deformation finite element analysis of automotive transmission mount using different material constants is performed and the load-displacement curves are compared with experiments. The selection of material constant in large deformation finite element analysis depend on the strain level of component in service.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.199-204
• /
• 2013

Owing to the global energy crisis, studies have strongly focused on realizing energy savings through vehicle weight reduction using light metal alloys or polymer composites. Polymer composites afford many advantages including enabling the fabrication of complex shapes by injection molding, and glass and carbon fibers offer improved mechanical properties. However, the high temperature in an engine room and the high humidity during the rainy season can degrade the mechanical properties of the polymer. In this study, the mechanical properties of injection-molded glass-fiber-reinforced polymer were assessed at a temperature of $85^{\circ}C$ and the maximum moisture absorption conditions. The result showed a 23% reduction in the maximum tensile strength under high temperature, 30% reduction under maximum moisture absorption, and 70% reduction under both heat and moisture conditions. For material selection during the design process, the effects of high temperature and high humidity should be considered.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.258-265
• /
• 2001

Compression and bending test have been conducted to evaluate the mechanical performance of CFRC at several different temperature up to $2000^{\circ}C$ . Tools and several grips for the test at high temperature were designed to obtain mechanical properties of CFRP. A major cause of increasing strength according to increasing the density and the temperature were analyzed. SEM method was utilized to find out the damage and the fracture mechanism. The new simple equation for the L(span length)/h(beam height) of specimens and for the failure criterion on the 4 point bending were proposed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1996.11a
• /
• pp.3-11
• /
• 1996

본 연구는 고체 추진기관의 각종 밀봉 부에 많이 사용되는 O-링의 설계시 고려되는 각종 형상인자의 변화에 따른 O-링의 거동과 응력 상태를 분석하여 설계 최적조건을 찾기 위한 내용을 다루고 있다. 조립 부의 내외경과 조립 공차, 챔퍼길이와 각도, 조립 홈의 외경, 깊이, 폭, 구성반경, O-링의 내경과 선 직경 등의 설계 변수에 의한 조립부 형상과 재료의 물성치, 유한요소 선택 및 요소 분할, 경계조건, 하중조건, 접촉부 정의 등을 MSC/PATRAN3의 $PCL^{[1]}$/로 프로그래밍 하여 설계변수에 의한 결과 분석을 손쉽게 수행할 수 있도록 시도하였다 고무의 Hyperelastic 물성치는 문헌상의 자료$자료^{[2]}$에 제시된 Ogden 상수를 사용하였으며 추후에는 인장시험, 순수전단시험, 이 축 인장시험을 통해 실험적으로 측정$^{[3]}$ 하여 적용할 예정이다. 고무의 대변형, 대 변형률을 고려한 비선형 응력해석은 MSC/PATRAN3의 Advanced FEA 모듈과 ABAQUS 5.5를 사용하였다. 본 연구에서의 해석결과를 설계변수들의 영향을 비교 분석하는데 사용하였으나 그 정확도가 입증된 상태는 아니며 추후 실제 조립 및 수압시험을 통해 평가할 예정이다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.5
• /
• pp.363-369
• /
• 2016

Enhancing mechanical strength of concrete has been fascinated using carbon-based nanomaterials such as CNT and graphene. The key to improving strength is a dispersion of nanomaterials. A novel method is required to investigate the dispersion inner concrete nondestructively. In this study, the optical optical properties such as refractive index and absorption coefficient are measured in nano-cement mortar specimens containing MWCNT and GO using THz electro-magnetic waves. From the results, the properties of nano-cement mortar are confirmed to be 1.0% to 2.5% higher in refractive index, and -14% to 28% higher in absorption coefficient than those of cement mortar at the average values. Using these characteristics, visualizing the dispersion of nano-concrete structures seems possible in future.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.5
• /
• pp.393-401
• /
• 2014

In this paper, we propose an evaluation scheme of the coefficients of thermal expansion (CTE) of constituents in composite materials using an inverse analysis. The size of constituents typically is about a few micrometers, which makes the identification of material properties difficult as well as the measurement results inaccurate. The proposed inverse analysis scheme, which is combined with the Mori-Tanaka method for predicting an equivalent CTE of composite materials, provides the CTE of the constituents in a straightforward manner by minimizing the cost function defined in lamina scale with the steepest descent method. To demonstrate the effectiveness and accuracy of the proposed scheme, the CTEs of several fibers (glass fiber, P75, P100, and M55J) embedded in matrix are evaluated and compared with experimental results. Furthermore, we discuss the effects of uncertainty of laminar and matrix properties on the prediction of fiber properties.

• Composites Research
• /
• v.32 no.4
• /
• pp.177-184
• /
• 2019

If what the mechanical properties according to a layer have was found out by analyzing the already fabricated composite, it could be possible to develop the composite of the better performance than the existing products. In this study, we tried to calculate the mechanical properties of the inner prepreg lamina by applying the reverse design technique to the composite structure made by laminating prepregs. When the physical quantities obtained by the simple tensile test are used alone and the physical quantities obtained by the tensile test and the mode analysis are used at the same time, the results of this study show that the accuracy of the latter is higher Finally, the maximum error of $E_1$ predicted was 0.09% and the maximum error of predicted $E_2$ was 7%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1339-1347
• /
• 2013

Creep through nanoindentations has attracted increasing research attention in recent years. Many studies related to indentation creep tests, however, have simply focused on the characteristics of steady-state creep, and there exist wide discrepancies between the uniaxial test and the indentation test. In this study, we performed a computational simulation of spherical indentations, and we proposed a method for evaluating the creep properties considering transient creep. We investigated the material behavior with variation of creep properties and expressed it using regression equations for normalized variables. We finally developed a program to evaluate the creep properties considering transient creep. By using the proposed method, we successfully obtained creep exponents with an average error less than 1.1 and creep coefficients with an average error less than 2.3 from the load-depth curve.