• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.161-168
• /
• 2018

This study is the analytical review on the inelastic region of CRC column strength curve. The inelastic region of CRC column strength curve is based on the Bleich theory and the maximum residual stress of $0.5{\sigma}_y$. This is somewhat conservative by considering the fact that the maximum residual stress of $0.3{\sigma}_y$ is well known. This study proposes column strength curve for nonlinear behavior of hot rolled structural steel members under axial force and tangent modulus Et, with the maximum residual stress of $0.3{\sigma}_y$ and compares them with those of CRC. The stress of the inelastic column under axial compression exceeds proportional limits and reaches yielding point before applied load render the column bent. The column strength curve that depends on gradually yielding state of section needs to be reviewed. In this study, it is derived that the critical load formular according to material yielding with the maximum residual stress of $0.5{\sigma}_y$ and compared with CRC column design curve.

• Journal of the Korean Magnetics Society
• /
• v.14 no.4
• /
• pp.143-148
• /
• 2004

Effects of residual flux density M$_{res}$ and number of inspection on the detection voltage and flux density B of the gas pipeline were investigated in MFL inspection, which is widely used for the non-destructive inspection in a gas pipeline. A simulation equipment composed of the magnetizer and iron ring attached on an aluminum disc was constructed instead of a huge gas pipeline facility. With this system. the iron ring could be perfectly demagnetized and signals from the bolt screw stuck on the disc could be clearly detected so that the effects of M$_{res}$S and the inspection number on the detection voltage and B of iron ring were effectively investigated. With increasing the number of inspection, M$_{res}$, B of the iron ring and the detection voltage decreased and then kept at constant values while final M$_{res}$ increased with increasing initial M$_{res}$. If inspection condition were kept unchanged, the detection voltage was proportional to the last M$_{res}$ of the iron ring instead of B. This was probably due to magnetic hysteresis of the iron ring inherited from magnetic domain so that consideration on the magnetic hysteresis was inevitable in the analysis of MFL signal from defects of a gas pipeline. A new inspection scheme using the magnetizer with reversed magnetization in the subsequent inspection was proposed from the result that a high detection voltage could be obtained in the first inspection of gas pipeline with positive M$_{res}$.

• Journal of the Korean Magnetics Society
• /
• v.10 no.5
• /
• pp.225-231
• /
• 2000

The crystallographic and magnetic properties of the sample F $e_{0.8}$ $Co_{0.18}$(BN)$_{0.02}$ synthesized by microwave arc-melting with the maximum power of 3.5 kW have been studied by the methods of an X-ray diffraction and the measurement of the magnetic hysteresis using the vibrating sample magnetometer at room temperature. The samples were prepared in a form of pellet pressed under the pressure of 9,000 N/c $m^2$, rolled coldly, and treated with the different temperatures. The X-ray diffraction pattern of pelleted sample shows that the crystal structure of the sample is bcc as same as that of Fe with a good uniformity. The X-ray diffraction pattern shows that a residual stress, which exists in the sample, is eliminated by final 90$0^{\circ}C$ annealing. As rolling rate and heat treatment temperature increases, the saturation magnetization and the remanence of the samples increase whereas the coercivity of the samples shows decrease. Also the saturation magnetization and the remanence of the samples were affected by rolling rate and rolling direction than heat treatment temperature, but the coercivity of the samples was affected by rolling rate and direction as well as heat treatment temperature. This means that a domain wall motion is easy due to elimination of a residual stress and an inclusion which exists in the sample by rolling and heat treatment and a local induced-magnetization easy axis was also formed to parallel to the rolling direction due to creation of the like-atom pairs across the slip plane by rolling......

• The Korean Journal of Pesticide Science
• /
• v.17 no.3
• /
• pp.145-154
• /
• 2013

Flonicamid was a water-soluble and systemic insecticide. It was applied to control neonicotinod pesticide-resistant cotton aphid in sweet peppers. However, the residue levels of total flonicamid in sweet pepper exported to Japan in 2009 were exceeded the maximum residue limit (MRL). This study was conducted to elucidate residual properties of flonicamid parent compound and its metabolites in sweet peppers. It was carried out to compare the variation of residues in sweet pepper in three different greenhouses for 21 days after 3 times application with 7 days interval. The mean residues were 0.176, 0.152 and 0.108 mg $kg^{-1}$ and the residue levels in sweet pepper among three greenhouses show significant difference. The maximum residue levels were detected 10 days later after last treatments. The overall residue levels were lower than MRL 2.0 mg $kg^{-1}$ (by Korea) and 0.4 mg $kg^{-1}$ (by Japan in 2009 but now revised MRL is 2.0 mg $kg^{-1}$). But the residue level of total flonicamid at the 21th day after 3 times treatment with 7 days interval was 0.429 mg $kg^{-1}$ restricted by the application of double rate than recommended rate. The amounts of metabolites, TFNA, 4-Trifluoro methyl nicotinic acid and TFNG, N-(4-trifluoro methyl nicotinoyl) glycine were increased while flonicamid parent compound was decreased over time. Therefore the longer trial period should be needed for flonicamid in sweet peppers.

• Bulletin of the Korean Institute for Industrial Safety
• /
• v.2 no.1
• /
• pp.34-40
• /
• 2002

화학설비나 산업설비 또는 국가 기간 설비에서 파이프(pipe)는 중요한 위치를 차지하고 있으며 파이프의 파열은 그대로 대형 사고나 설비 가동의 중단으로 연결되는 경우가 많다. 따라서 파이프의 구조건전성을 유지하는 것은 안전의 확보와 생산 설비의 효율적 운용을 위하여 긴요하다. 파이프 재료 내부에는 재료 제작 시, 또는 파이프 제작 시 발생된 결함이나 사용 중 부식이나 피로 등의 영향으로 생성된 결함이 존재한다. 이러한 결함은 파이프의 강도를 낮추게 되고, 파이프의 잔류강도가 사용압력보다 낮아지게 되면 파이프가 파열하게 된다. 따라서 본 글에서는 파이프에 균열이 존재하거나 손상된 경우의 구조안전성 평가를 위하여 필요한 해석방법에 대하여 살펴본다.(중략)

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.1
• /
• pp.20-26
• /
• 2014

This paper represented the finite element analysis to estimate structural performance of stress-laminated deck, which is determined by deflection, stress, and aging characteristics of tensioning. After loading, the deflected shape showed plate behavior because pre-stressing make frictional force between each member. Compared between initial post-tension and the results, pre-stressing forces were decreased with deck deflection. This is because deflection occurred in the deck so that pre-stressing decreased due to load reduction. However, material plasticity was not considered so that advanced researches should be performed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.4
• /
• pp.328-333
• /
• 2003

It has been widely recognized that the residual stress of the weldment affect the integrity of steel structures and cause an initiation of crack in the welded regions. Since the power plants adopt a variety of welding processes, it is necessary to know the distribution and magnitude of residual stresses. This paper has attempted to investigate the validity of the saw cutting method and the indentation method to measure the residual stresses in the steel plates. The residual stresses in the specimens of hot reheater pipes, cold reheater pipes and feed water lines in power plants were determined by the saw cutting method and the indentation method. The data were compared and reviewed for the validity of the methods.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.8
• /
• pp.13-21
• /
• 2014

The Plastic Board Drain is used to improve soft soils deposited in container terminal area at a port. This paper describes settlement behavior of soft ground in this area from PBD installation to the time of operating facilities. Previous researches focused on soil improvement effect of PBD, that is, the settlement occurred during ground improvement period. The residual settlement occurred during operating the facility is very important from the maintenance and management point of view. However, the study of this residual settlement has been rarely conducted. In this study, by analyzing the measured settlement data obtained from the container terminal area at the port, it was verified that the residual settlement induced during operating facilities occurred in a layer with PBD improvement. In addition, by comparison the settlement predicted by a numerical analysis with the settlement measured in the field, it was confirmed that the actual settlement is in the range of predicted settlement.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.1
• /
• pp.16-24
• /
• 1999

Residual stress is one of the causes which make defects in engineering components and materials. And interest in the measurement of residual stress exists in many industries. There are commonly used methods by which residual stresses are currently measured. But these methods have a little demerits. time consumption and other problems. Therefore we devised a new experimental technique to measure residual stress in materials with a combination of laser speckle pattern interferometry, finite element method and spot heating. The speckle pattern interferometer measures in-plane deformations while the heating provides for very localized stress relief. FEM is used for determining heat temperature and other parameters. The residual stresses are determined by the amount of strain that is measured subsequent to the heating and cool-down of the region being interrogated. A simple model is presented to provide a description of the method. In this paper, the ambiguity problem for the fringe patterns has solved by a phase shifting method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.1
• /
• pp.18-22
• /
• 2014

Residual stresses that occur during the welding process, are the main cause of failure and defects in welded structures. This paper, presents the use of an electronic processing laser speckle interferometer to measure the residual stress of a welded pipe for a nuclear power plant. A tensile testing machine was used to evaluate a welded pipe that failed in compression. The inform plane deformation and modulus of elasticity of the base metal and welds were measured using an interferometer. Varying the load on the welded pipe had a larger effect on the deformation of the base metal the other properties of the base metal and welds. The elastic moduli of the base metal and weld of the welded pipe were 202.46 and 212.14 GPa, respectively, the residual stress was measured to be 6.29 MPa.