• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1994.11a
• /
• pp.23-27
• /
• 1994

고분자 전해질형 연료전지의 성능을 향상시키기 위하여 막-전극 어셈블리 제조시 hot-pressing 온도와 압력조건을 변화시켜며 단위전지 성능을 관찰하였으며 이에 대한 분석은 열무게분석법(TGA), 기공도, 이온투과계수 등을 사용하였다. 또한 전지의 작동온도 및 압력을 변화시켜가며 전지의 성능을 관찰하였다. 성능 실험은 가습기의 온도와 cell의 온도, 압력을 변화시켜가며 측정하였다.

• Journal of the korean Society of Automotive Engineers
• /
• v.26 no.3
• /
• pp.21-25
• /
• 2004

연료전지의 종류는 전해질의 종류로 나누는 것이 일반적으로, 운전 및 정지를 반복하는 자동차용에는 작동 온도까지 상변화가 없는 고체 전해질이 유리하다고 할 수 있는데 프로톤 교환막과 고체산화물이 바로 그것이다. 프로톤 교환막 연료전지는 다른 종류의 연료전지 보다 작동온도가 8$0^{\circ}C$ 내외로 낮고, 단위전지 면출력밀도가 커서 현재 자동차용으로 가장 많이 개발되고 있다. 그 결과 자동차 구동에 적당한 80㎾급의 연료전지 스택이 자동차에 장착될 수 있는 크기로 개발되어 적용되고 있다. (중략)

• Solar Energy
• /
• v.15 no.2
• /
• pp.77-90
• /
• 1995

An effective heat transfer during freezing process was proposed in the vertical cylinder to improve the effectiveness of the heat storage. Vertical cylinder was filled with pure water in order to investigate ice-shape, temperature distribution of the liquid, temperature distribution of the cylinder tube wall, total heat storage per unit mass in the test section under the two experimental conditions; inlet temperature of working fluid is constant($-10^{\circ}C$) and inlet direction of working fluid is either upward flow or downward. Both the mean temperature of the liquid and temperature difference of cylinder tube wall in the upward were lower than those in the downward. In case that the initial temperature of water was $7^{\circ}C$ and $4^{\circ}C$, the shape of ice layer in the upward was more uniform than that in the downward. In case of $1^{\circ}C$, the shape of ice layer is formed by inlet direction of working fluid. Finally, time-varying total heat energy stored in the water in the upward was higher than that in the downward.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.881-889
• /
• 2015

Ocean thermal energy conversion is an organic Rankine cycle that generates power using the temperature difference between surface water and deep water. This study analyzes the thermodynamic efficiency of the cycle, which strongly depends on the working fluid and the cycle configuration. Cycles studied included the classical simple Rankine cycle, Rankine cycles with an open feedwater heater and an integrated regenerator, as well as the Kalina cycle. Nine kinds of simple refrigerants and three kinds of mixed refrigerants were investigated as the working fluids in this study. Pinch-point analysis that set a constant pinch-point temperature difference was applied in the performance analysis of the cycle. Results showed that thermodynamic efficiency was best when RE245fa2 was used as the working fluid with the simple Rankine cycle, the Rankine cycles with an open feedwater heater and an integrated regenerator, and when the mixing ratio of $NH_3/H_2O$ was 0.9:0.1 in the Kalina cycle. If the Rankine cycles with an open feedwater heater, an integrated regenerator, and the Kalina cycle were used for ocean thermal energy conversion, efficiency increases could be expected to be approximately 2.0%, 1.0%, and 10.0%, respectively, compared to the simple Rankine cycle.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.43-49
• /
• 2013

The use of ocean thermal energy conversion (OTEC) to generate electricity is one of the methods proposed to utilize renewable energy and to protect the environment. In this study, simulations were performed to investigate the effect of weather conditions in the Ulsan region, Korea, on the efficiency of a solar-heating OTEC (SH-OTEC) system. This system utilizes solar thermal energy as the secondary heat source. Various working fluids were also simulated to select one that is suitable for this system. The results showed that R152A, R600, and R600A, in that order, were the most suitable working fluids. The effective area of the solar collector for a $20^{\circ}C$ increase in the collector outlet temperature fluctuated from 50 to $97m^2$ owing to the change in the monthly average solar gain. The annual average efficiency of the SH-OTEC increases to 6.23%, compared to that of a typical conventional OTEC, which is 2-4%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.116-116
• /
• 2010

진공 chamber에서 방전된 plasma 내부를 외부 view port를 통하여 확인하는 것은 극히 제한적이며 leak의 확률을 높이고 plasma의 균일한 방전을 방해한다. 이를 개선하기 위하여 내장형 무선 카메라를 chamber 내부에 위치한 후 고진공 영역에서 촬영을 시도하였으나 일반적인 CCD 카메라로는 촬영할 수 없다. 고진공 영역에서 카메라 내부온도의 급격한 상승이 원인으로 밝혀졌고 적정온도인 $45^{\circ}C$를 초과하여 최대 $96^{\circ}C$까지 4 min 이내에 상승함을 IR camera로 확인할 수 있었으며 이 때 카메라가 작동하지 않았다. 또한 카메라를 고진공 영역에서 촬영 및 녹화하기 위해서는 $46^{\circ}C$의 온도를 낮추어야 함을 진공해제 이후 내부온도가 $50^{\circ}C$로 감소하면서 내장형 무선 카메라가 다시 작동함으로 인해 알 수 있었다. 본 연구에서는 이를 해결하기 위하여 내장형 무선 카메라에 AM 변조 방식의 311 MHz RF remote controller를 장착하여 외부에서 선택적으로 ON/OFF 할 수 있도록 개조하였고 10 L chamber에서 150 L/sec TMP를 이용하여 10-6 Torr의 압력에서 성공적으로 녹화 및 촬영하였다. 또한 내장형 무선 카메라 내부의 반도체 회로 규격 및 발열량과 heat sink의 규격 (열전도도, 복사율)을 추가로 조사하였다. 분자유동 영역에서 열전달은 복사에 의한 영향이 대부분이므로 내장형 무선 카메라 내부 온도를 감소시켜 카메라의 작동 시간을 연장하기 위하여 내부 회로에 emissivity가 높고 전기전도도가 낮아 회로에 영향이 없는 박막을 회로에 증착시키는 추후의 연구가 필요하다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.12
• /
• pp.821-827
• /
• 2010

Study on the performance characteristics of the solar hybrid system with heat pump operating temperature during winter season has performed by using an experimental test. The system performance and operating characteristics with the heat pump operating temperature, hour and load condition were investigated and analyzed. As a result, the hot water temperature was significantly affected by the heat pump operating temperature at the morning(time 1) and noon(time 2). However, hot water temperature was set by the radiation quality and collecting operation hour at the afternoon(time 3). In addition to the solar fraction was decreased for the high heat pump operating temperature because the heat pump operated with a long operating time and short operating period.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.478-483
• /
• 2017

This paper investigated experimentally the performance of cooling systems using thermoelectric and piezoelectric modules for local heating and temperature control, such as a handheld electronic devices. The temperature distribution of the cooling region using thermoelectric modules was measured when the piezoelectric module was and was not with a frequency of 80Hz and 110Hz. The coefficients of performance were also calculated by the temperature results, and the thermo-flow phenomena in the cold region was visualized under the same conditions. The results of the temperature distribution measurements and the coefficient of performance showed that the cooling performance of the cooling system using thermoelectric modules can be improved by operating the piezoelectric module. In addition, when the piezoelectric module was operated based on the result of visualization in the cold region, which was formed by thermoelectric modules, the performance thermoelectric cooling was improved by the thermo-flow formed in the entire cold region as the forced convection of vibration was generated on the local cold region by the piezoelectric module.

• Journal of the KSME
• /
• v.31 no.8
• /
• pp.735-744
• /
• 1991

확산모델과 파모델의 결과에 있어 큰 차이가 일어나는 경우를 요약하면 다음과 같다. 1) 과도기 간이 짧다. 2) 작동온도가 아주 낮다. 3) 온도구배가 상당히 크다. 이때3)의 경우는 서로 다른 물질들이 접촉된 경우 또는 높은 열유속이 있는 경우 또는 얇은 표면층 등을 갖는 문제들의 공 통적인 특징이다. Non-Fourier 열전도 문제를 이용해 온도 분포를 예측해야 하는 실제적인 몇 가지 예를 살펴 보면 레이저 기술 또는 절대온도 영(zero)에 접근하는 온도에서의 액체 헬륨을 다루는 저온공학연구 또는 1/$10^{6}$Inch 정도의 표면조도가 관심사인 정밀공학 등을 들 수 있다. 또한 상당히 높은 강도의 열원이 작용될 때 고체에서의 크랙이나 보이드(void) 같은 국소 결함은 확산거동이 나타나기에 요구되는 시간보다 짧은 시간 구간에서 발생되어질 수 있으며, 크랙발생의 방향과 같은 것들은 hyperbolic 모델에의해 예측되어져야만 한다. 특히 움직이는 열원 또는 propagating crack tip을 갖는 경우에 그들 주위에서의 온도장을 규정짓는 가장 중요한 변 수는 열마하수 M이며, 아음속에서 초음속 영역으로 천이될 때 물리적 양들의 변화에 있어서 일어나는 현상들은 열충격의 형성에 기인하는데 이러한 현상들은 확산 모델로서는 예측될 수 없는 특징들이다. 이상에서 살펴볼 때 non-Fourier 모델에 대해 관심을 기울일 필요가 있다고 사료된다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1151-1157
• /
• 2012

Ocean Thermal Energy Conversion(OTEC) technology is one of the new and renewable energy that utilizes the natural temperature gradient that exists in the tropical ocean between warm surface water and the deep cold water, to generate electricity. The selection of working fluid and the OTEC cycle greatly influence the effect on the system operation, and it's energy efficiency and impacts on the environment. Working fluids of the OTEC are ammonia, R22, R407C, and R410A. In this paper, we compared boiling pressure to optimize OTEC system at $25^{\circ}C$. Also, this paper showed net-power and efficiency according to working fluids for closed cycle and regeneration cycle.