• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.31 no.7
• /
• pp.53-64
• /
• 2002

$CO_2$ 20세기 초 천연 냉매 $CO_2$는 광범위하게 사용되었지만 프레온계 냉매의 출현으로 1940년경부터 $CO_2$냉매는 사용이 제한되었다. 그러나 반 세기 동안 사라졌던 $CO_2$냉매는 1980년 후반에 노르웨이 과학 기술대학 (NTNU)과 북구 최대 민간연구소 (SINTEF)의 Lorentzen 교수에 의해 $CO_2$천연 냉매 사용을 재고하게 되었다. 프레온계 냉매의 환경적 논쟁이 쟁점이 되면서 천연 냉매 사용을 재고하게 되었다. 특히 비가연성과 비유독성으로 인한 $CO_2$냉매가 주목을 받고 있다. 초월임계 사이클레서의 고압 제어에 대한 새로운 개념은 Lorentzen 교수와 동료 연구원에 의해서 특허로 제안되었다. 이에 대한 상업적 권리를 Norsk Hydro사는 1990년에 얻었고,1990년대 초반에 NTNU/SINTEF의 공동 연구개발 프로그램을 통해 기술 경쟁력과 실현 가능성이 검증되었다. 현재 연구소에서는 최초로 초월임계 $CO_2$사이클을 이용한 상업용 온수 열펌프 시스템, 2003년 시작할 연료전지 전기 자동차에 대한 연구를 수행하고 있다. NTNU/SINTEF에서 개발된 $CO_2$기술은 Hydro-SINTEF 공동 벤처 기업인 Shecco기술회사를 통해 제조업자에게 허가된다. 본 고에서는 NTNU/SINTEF에서 수행하였거나 수 중인 과제들을 중심으로 유럽의 $CO_2$시스템의 결과와 주요 개발 범위를 정리하였으며, 특히 작동유체로서의 $CO_2$냉매의 특징을 간단히 설명하고, 온 수 열 펌프, 자동차용 공조기 및 열 펌프, 상업 냉동기 등이 기술되었다. 그 외 압축기 위주의 요소기술 개발에 관한 내용도 기술되었고, 차세대 기술 경향과 전망에 대해서도 제시되었다. 제시되었다.성균 350$\times$$10^4$ CFU균, 방선균 434$\times$$10^4$ CFU균, 진균 676$\times$$10^4$ CFU균으로 진균의 개체수가 비교적 높게 나타났으며, 비산불지역에서는 호기성균 328$\times$$10^4$ CFU균, 방선균 319$\times$$10^4$ CFU균, 진균 461$\times$$10^4$ CFU균으로 진균의 개체수가 높게 나타났다. 토양미생물은 호기성균, 방선균, 진균 모두 비산불지역 보다 산불지역에서 많이 나타났다. 본 조사지역에서 호기성균은 활엽수림보다 침엽수림에서 많게 나타났으며, 방선균과 진균은 침엽수림보다 활엽수림에서 많이 나타났다.효과와 이를 이용한 자기냉동의 방법 그리고 최근에 이루어진 새로운 진전에 대해 소개하고 공기조화 및 냉동분야에의 적용 가능성을 전망해 보고자 한다.및 도입 등 선주들에게 다양한 선박건조자금을 제공하여 내수기반 확충에도 노력해야 할 것 이다.있었다., 인삼이 성장될 때 부분적인 영양상태의 불충분이나 기후 등에 따른 영향을 받을 수 있기 때문에 앞으로 이에 대한 많은 연구가 이루어져야할 것으로 판단된다.태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다. 즉, [+wh] 의미의 겹의문사는 동일한 구성요 소를 지닌 병렬적 합성어([$[W1]_{XO-}$ $[W1]_{XO}$ ]$_{XO}$)로 그리고 [-wh] 의미의 겹의문사는 중복된 발은을 지닌 한 단어로 ([W]$_{XO}$ )

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.25-32
• /
• 2007

Because of the increasing use of clayey soil as the backfill in reinfurced soil structures and embankments, nonwoven geotextiles of drain capability have been receiving much attention. However, there are few studies on the deformation behavior analysis of nonwoven geotextiles in reinforced soil structures in the site because nonwoven geotextiles which have low tensile stiffness and higher deformability than geogrids and woven geotextiles, are difficult to measure their deformation by using strain gauges. In this study, it was suggested that a new and more convenient method could measure the deformation behaviour of nonwoven geotextile using a strain gauge and examine the availability of the method by conducting laboratory tests and applying to two geosynthetics reinforced soil (GRS) walls in the site. The result of wide-width tensile test conducted under confining pressure of 70 kPa shows that the local deformation of nonwoven geotextile to be measured with strain gauges has a similar pattern to the total deformation measured with LVDT. In the GRS walls, nonwoven geotextile shows a larger deformation range than the woven geotextile and geogrid. However, the deformation patterns of these three reinforcement materials are similar. The function of strain gauges attached to nonwoven geotextile in the walls works normally for 16 months. Therefore, the method proposed in this study for measuring nonwoven geotextile deformation using a strain gauge has proved useful.

• Design Convergence Study
• /
• v.16 no.6
• /
• pp.169-184
• /
• 2017

There is a lot of needs that are not expressed as much as the expressed needs in familiar products and services that are used in daily life such as a smartphone. Finding the 'Inconveniences in familiar use' make it possible to create opportunities for value expanding in the existing products and service area. There are a lot of related works, which have studied the definition of hidden needs and the methods to find it. But, they are making it difficult to address the hidden needs in the cases of familiar use due to focus on the new product or service developing typically. In this study, we try to redefine the hidden needs in the daily familiarity and approach it in the new way to find out. Because of the users' unability to express what they want and the complexity of needs which can not be explained clearly, we can not approach it as the quantitative issue. For this reason, the basic data type selected as the user behavior data excluding all description is the screen-shot of the smartphone. We try to apply the integrated rules and patterns to the individual data using the qualitative coding techniques to overcome the limitations of qualitative analysis based on unstructured data. From this process, We can not only extract meaningful clues which can make to understand the hidden needs but also identify the possibility as a way to discover hidden needs through the review of relevance to actual market trends. The process of finding hidden needs is not easy to systemize in itself, but we expect the possibility to be conducted a reference frame for finding hidden needs of other further studies.

• Journal of Venture Innovation
• /
• v.5 no.2
• /
• pp.85-99
• /
• 2022

Dryers becoming commercially available for experimental and industrial use are classified to general drying oven, hot-air dryer, vacuum dryer, freezing dryer, etc. and kinds of them are various from the function, size and volume, etc. But the moisture measurement is not applied although it is important factor for the quality control and the performance improvement of products, and then now is very passive because the weight is weighed arbitrarily after dry-end. Generally the method for measuring moisture is divided by a direct measurement method and a indirect measurement method, and the former such as the change of weight or volume on the front and rear of separation of moisture, etc. is mainly used. Relatively a indirect measurement is very limited to apply due to utilize measurement apparatuses using temperature conductivity and micro-wave etc. In this research, we easily designed the moisture measurement system using the open-source based Arduino, and monitored moisture fluctuations and weight profiles in the real-time without the effect of external environment. Concretely the temperature-humidity and load cell sensors were packaged into a drying oven and the various change values were measured, and their sensors capable to operate 60℃ and 80℃ were selected to suitable for the moisture sensitive materials and the food dry. And also the performance safety using the organic samples of banana, pear, sawdust could be secured because the changes of evaporation rate as the dry time and temperature, and the measurement values of load cell appeared stable response characteristics through repeated experiments. Hereafter we judge that the reliability can be improved increasingly through the expansion of temperature-humidity range and the comparative analysis with CFD(Computational Fluid Dynamics) program.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1461-1464
• /
• 2019

In this paper, we propose the development of embedded board for integrated radiation exposure protection fireman's life-saving alarm capable of location tracking and radiation measurement. The proposed techniques consist of signal processing unit, communication unit, power unit, main control unit. Signal processing units apply shielding design, noise reduction technology and electromagnetic wave subtraction technology. The communication unit is designed to communicate using the wifi method. In the main control unit, power consumption is reduced to a minimum, and a high performance system is formed through small, high density and low heat generation. The proposed techniques are equipment operated by exposure to poor conditions, such as disaster and fire sites, so they are designed and manufactured for external appearance considering waterproof and thermal endurance. The proposed techniques were tested by an authorized testing agency to determine the effectiveness of embedded board. The waterproof grade has achieved the IP67 rating, which can maintain stable performance even when flooded with water at the disaster site due to the nature of the fireman's equipment. The operating temperature was measured in the range of -10℃ to 50℃ to cope with a wide range of environmental changes at the disaster site. The battery life was measured to be available 144 hours after a single charge to cope with emergency disasters such as a collapse accident. The maximum communication distance, including the PCB, was measured to operate at 54.2 meters, a range wider than the existing 50 meters, at a straight line with the command-and-control vehicle in the event of a disaster. Therefore, the effectiveness of embedded board for embedded board for integrated radiation exposure protection fireman's life-saving alarm has been demonstrated.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.3
• /
• pp.13-19
• /
• 2018

The soldering property of Pb-containing solder(Sn-Pb) and Pb-free solders(Sn-3.0Ag-0.5Cu and Sn-1.0Ag-0.7Cu-1.6Bi-0.2In) for solar combiner box module was compared. The solar combiner box module was composed of voltage and current detecting modules, diode modules, and other modules. In this study, solder paste printability, printing shape inspection, solder joint property, X-ray inspection, and shear force measurements were conducted. For optimization of Pb-free soldering process, step 1 and 2 were divided. In the step 1 process, the printability of Pb-containing and Pb-free solder alloys were estimated by using printing inspector. Then, the relationship between void percentages and shear force has been estimated. Overall, the property of Pb-containing solder was better than two Pb-free solders. In the step 2 process, the property of reflow soldering for the Pb-free solders was evaluated with different reflow peak temperatures. As the peak temperature of the reflow process gradually increased, the void percentage decreased by 2 to 4%, but the shear force did not significantly depend on the reflow peak temperature by a deviation of about 0.5 kgf. Among different surface finishes on PCB, ENIG surface finish was better than OSP and Pb-free solder surface finishes in terms of shear force. In the thermal shock reliability test of the solar combiner box module with a Pb-free solder and OSP surface finish, the change rate of electrical property of the module was almost unchanged within a 0.3% range and the module had a relatively good electrical property after 500 thermal shock cycles.

• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.419-427
• /
• 2012

This study was carried out to investigate the effect of two shading methods, shading agent spray on the glasshouse and internal shading screen treatment, on the growth and fruit quality of paprika (Capsicum annuum L. 'Cupra' and 'Coletti') in summer season cultivation. In the shading agent treatment, a commercial shading agent diluted with water at a ratio of 1 : 4 was sprayed on the roof of a glasshouse. In the internal shading screen treatment, a 10~20% shaded screen was used during the day time when the sun radiation was greater than $700W{\cdot}m^{-2}$. Compared to the unshaded control, photosynthetic photon flux density (PPFD) decreased in the greenhouse in the shading agent (SA) and shading screen (SS) treatments by 20% and 30%, respectively. Lower air temperatures and higher relative humidities were observed in the SA than in both the control and the SS treatment. Time to reach the break point of humidity deficit $8g{\cdot}m^{-3}$ was 2 hours late in the SA than in both the control and the SS treatment. Compared to control, both the SA and the SS treatments showed lower instantaneous temperatures of leaf, fruit, and flower by $2^{\circ}C$, $5^{\circ}C$ and $3^{\circ}C$, respectively. There were no differences in number of branches, stem diameter, and leaf size among treatments although both shading treatments promoted plant height in both cultivars. Botrytis infection ratio declined with the SA treatment by 14.7% in 'Cupra' and 22.1% in 'Coletti' as compared to that in the control. Shading increased fruit size in both cultivars, whereas no differences were observed in the number of locules and thickness of fruit tissue among treatments. Shading treatment increased mean fruit weight by a range of 10 to 15 g per fruit, while it decreased soluble solids contents as compared to that in the control. Similar Hunter values were observed among treatments, while fruit firmness increased slightly in shading treatments. Compared to the control, shading treatments improved marketable fruits by 11.7~22.6% and increased the number of fruits per plant by 4~9.2 in both 'Cupra' and 'Coletti'. The results of this study indicate that shading agent application on the roof of glasshouse would be one of the most effective options to reduce heat stress imposed on the paprika crop in summer cultivation, resulting in improved crop growth and fruit yield.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.4
• /
• pp.257-267
• /
• 2023

Purpose. The purpose of the study was to fabricate a prototype robotic simulator for dental education, to test whether it could simulate mandibular movements, and to assess the possibility of the stimulator responding to stimuli during dental practice. Materials and methods. A virtual simulator model was developed based on segmentation of the hard tissues using cone-beam computed tomography (CBCT) data. The simulator frame was 3D printed using polylactic acid (PLA) material, and dentiforms and silicone face skin were also inserted. Servo actuators were used to control the movements of the simulator, and the simulator's response to dental stimuli was created by pressure and water level sensors. A water level test was performed to determine the specific threshold of the water level sensor. The mandibular movements and mandibular range of motion of the simulator were tested through computer simulation and the actual model. Results. The prototype robotic simulator consisted of an operational unit, an upper body with an electric device, a head with a temporomandibular joint (TMJ) and dentiforms. The TMJ of the simulator was capable of driving two degrees of freedom, implementing rotational and translational movements. In the water level test, the specific threshold of the water level sensor was 10.35 ml. The mandibular range of motion of the simulator was 50 mm in both computer simulation and the actual model. Conclusion. Although further advancements are still required to improve its efficiency and stability, the upper-body prototype simulator has the potential to be useful in dental practice education.

• Cartoon and Animation Studies
• /
• s.33
• /
• pp.597-616
• /
• 2013

Character industry is not only knowledge-based industry chiefly with copyrights but also motive power for creative economy to take a role functionally over the fields of industries because it has industrial characteristic as complement product to promote sale value in manufacturing industry and service industry and increase profit on sales. Since 2003, the national policy related to character has aimed to maximize effect among connected industries, extend its business abroad, enforce copyrights through the improvement of marketing system, develop industrial infrastructure through raising quality of character products. With the result of this policy, the successful cases of connected contents have been crystallized and domestic character industry has stepped up methodically since 2007. It is needed to reset the scales of character industry and industrial stats because there are more know-how of self industry promotion and more related characters through strategy of market departmentalization starting with cartoon, animation, games, novels, movies and musicals. Especially, The Korea government set our target for 'Global Top Five Character Power' since 2009 and has started to carry out to find global star characters, support to establish network among connected industries, diversify promotion channels, and develop licensing business. Particularly, since 2013, There have been prospered the indoor character theme park with time management just like character experimental marketing or Kids cafes using characters, the demand market of digital character focusing on SNS emoticon, and the performance market for character musical consistently. Moreover, The domestic and foreign illegal black markets on off-line have been enlarged, so we need another policy alternative. To prepare for the era of exploding character demand market and diversifying platform, it is needed to set up a solid strategy that is required the elements of policy changes in character industry to vitalize character industry and support new character design and connected contents. the following shows that the elements of policy changes related to the existing policy, the current position of market. Nowadays, the elements of policy changes in domestic character industry are that variety of consumers in the digital character market according to platform diversification, Convergence contents of character goods for the Korean waves, legalization of the illegal black contents market, and controling the tendency of consumers in departmentalized market. This can help find the policy issue entirely deferent with the existing character powers like US, Japan or Europe. In its final analysis, the alternatives are the promotion of models with contract copyrights of domestic and foreign connected contents, the diversification of profit models of platform economy, the additive development of target market related to enlarging the Korean waves, and the strategy of character market for the age-specific tendency according to developing character demand market.

• Analytical Science and Technology
• /
• v.27 no.1
• /
• pp.34-40
• /
• 2014

SPLITT fractionation (SF) allows continuous (and thus a preparative scale) separation of micronsized particles into two size fractions ('fraction-a' and 'fraction-b'). SF is usually carried out in a thin rectangular channel with two inlets and two outlets, which is equipped with flow stream splitters at the inlet and the outlet of the channel, respectively. A new large scale splitter-less gravitational SF (GSF) system had been assembled, which was designed to eliminate the flow stream splitters and thus is operated by the full feed depletion (FFD) mode (FFD-GSF). In the FFD mode, there is only one inlet through which the sample is fed. There is no carrier liquid fed into the channel, and thus prevents the sample dilution. The effects of the sample-feeding flow rate, the channel thickness on the fractionation efficiency (FE, number % of particles that have the size predicted by theory) of FFD-GSF was investigated using industrial polyurethane (PU) latex beads. The carrier liquid was water containing 0.1% FL-70 (particle dispersing agent) and 0.02% sodium azide (used as bactericide). The sample loading rate was varied from about 4 to 7 L/hr with the sample concentration fixed at 0.01%. The GSF channel thickness was varied from 900 to $1300{\mu}m$. Particles exiting the GSF channel were collected and monitored by optical microscopy (OM). Sample recovery was monitored by collecting the fractionated particles on a $0.45{\mu}m$ membrane filter. It was found that FE of fraction-a was increased as the channel thickness increases, and FE of fraction-b was increased as the flow rate was increased. In all cases, the sample recovery has higher than 95%. It seems the new splitter-less FFD GSF system could become a useful tool for large scale separations of various types of micron-sized particles.