• Economic and Environmental Geology
• /
• v.46 no.3
• /
• pp.215-220
• /
• 2013

We estimated the hydraulic conductivity of the sediments using constant-head permeability tests and electrical resistivity measurements with Jumoonjin standard sand of a uniform size and glass beads of different grain sizes. In this study, we determined the variations of the porosity, the hydraulic conductivity, and the resistivity in case 1 (changing the packing of the Jumoonjin standard sand) and in case 2 (varying the size of the glass beads). The results of case 1 showed that the hydraulic conductivity decreased with an increase in the electrical resistivity. This occurred because the sand grain while packing became rhombohedral with the a decrease of both the pore size and porosity. The results of the case 2 showed that the hydraulic conductivity increased due to the increase in the pore size as caused by the increased glass bead size. In addition, the porosity decreased and the electrical resistivity increased. Therefore, the relationship between the hydraulic conductivity and the electrical resistivity is negatively proportional as regards the grain packing with a change from cubic to rhombohedral whereas this relationship is positively proportional to the increase in the grain size.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.602-609
• /
• 1997

The seed formation and growth of $\alpha$-ferric oxyhydroxide with aerial oxidative precipitation from aqueous solution of ferrous sulfate with KOH, NaOH, $Na_2CO_3$ and $K_2CO_3$ as precipitants have been studied by free pH drift experiment. It has been shown that all precipitants give same particle formation and growth path, and average particle length from KOH and NaOH as precipitants was about 1.5 times shorter than that of $K_2CO_3$ and $Na_2CO_3$. When initial mole ratio, $R_o=[Fe^{2+}]_o/[OH^-]_o$ of KOH was decreased the particle was grown oxyhydroxide seed growth from aqueous solution of ferrous sulfate with KOH has been studied. The influence of the air flow rate, reaction temperature and initial mole ratio, $R_o=[Fe^{2+}]_o/[OH^-]_o$, on the kinetics of seed growth are investigated by static pH experiment. The oxidation rate of seed growth increased with increase in the air low rate, reaction temperature and initial mole patio. The activation energy of seed growth is 16.16 KJ/mol and the rate equation of seed growth can be written as follows: $-\frac{d[Fe^{2+}]}{dt}=1.46{\times}10^4[P_{o2}]^{0.66}[OH^-]^{2.19}exp(-\frac{16.16}{dt})$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.954-961
• /
• 2008

An experimental study has been conducted to investigate the flow field around the wing having a circular damage hole. The damage was represented by a circular hole passing through the model with 10% airfoil chord diameter and normal to the chord. The hole was centered at quarter or half chord. The PIV flow fields and static pressure measurements on the wing upper and lower surface were carried out at Rec=2.85×105 based on the chord length. The PIV results showed the two types of flow structures around a damage hole were formed. The first one was a weak jet that formed an attached wake behind the damage hole. The second one resulted from increased incidence; this was a strong jet where the flow through the hole penetrates into the free-stream resulting in extensive separation of oncoming boundary layer flow and development of a separated wake with reverse flow. The surface pressure data showed a big pressure alteration near the circular damage hole. The severity of pressure alteration was increased as a damage hole located nearer to the leading edge.

• Food Engineering Progress
• /
• v.21 no.3
• /
• pp.225-232
• /
• 2017

Most of the red ginseng (RG) products contain active substances derived from hot water or alcohol extraction. Since active substances of RG are divided into two types - water-soluble and liposoluble - water or alcohol is needed as an extraction solvent and this leads the different extraction yields and components of the active substances. To overcome the limit, whole red ginseng powder can be used and consumed by consumers. In this study, the physicochemical properties and extractable active substance contents of variable-sized RG powder ($158.00{\mu}m$, $8.45{\mu}m$, and $6.33{\mu}m$) were analyzed, and dispersion stability was measured to investigate the suitable size of RG powder for industrial processing. In the results, no significant difference was found from the changes in color intensity and thiobarbutric acid tests at $4^{\circ}C$, $25^{\circ}C$, and $40^{\circ}C$ for 4 weeks. There was no significant difference on the production of antioxidants and ginsenoside among the samples (p>0.05). In dispersion stability, $RG-158.00{\mu}m$ was precipitated immediately, and the dispersion stabilities between $RG-8.45{\mu}m$ and $RG-6.33{\mu}m$ showed no significant difference. It implies that fine RG is suitable for the production process. With further study, it seemed that the physicochemical effects of RG particle sizes can be clearly revealed.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1202-1207
• /
• 2003

Using a recently developed Hybric Plasma-Particle Accelerating Impact Deposition (HP-PAID) process, synthesis of nanostructured silicon coatings has been investigated by injecting vapor-phase TEOS (tetraethosysilane, (C$_2$H$\_$5/O)$_4$Si) into an Ar hybrid plasma. The plasma jet with reactants was expanded through nozzle into a deposition chamber, with the pressure dropping from 700 to 10 torr. Ultrafine particles accelerated in the free jet downstream of the nozzle, deposited by an inertial impaction onto a temperature controlled substrate. By using this process, nanostructured amorphous silicon coatings with grain size smaller than 10 nm could be synthesized. These samples were annealed in an Ar and crystallized at 900$^{\circ}C$ for 30 min. TEM analysis showed that the annealed coatings were also composed of nanoparticles smaller than 10 nm, which showed a good consistency that the average grain size of 7 nm was also estimated from a peak shift of 2.39 cm$\^$-1/ and Full Width at Half Maximum (FWHM) 5.92 cm$\^$-1/ of Raman analysis. The noteworthy is that a strong PL peak at 398 nm was also obtained for this sample, which indicates that the deposited coatings also contained 3∼4 nm nanostructured grains.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.10a
• /
• pp.46-47
• /
• 2010

추진기와 타가 놓여있는 선미부에서의 난류 유동에 의한 저항을 증가시키는 요인이 집중되어 있다. 트랜섬 선미를 가지고 있는 선박의 경우 선미선형에 의한 저항의 형태가 달라진다. $Re=2.8{\times}10^5$의 균일흐름에서, 선저와 트랜섬이 이루는 각도를 각각 $45^{\circ}$, $90^{\circ}$, $135^{\circ}$로 변형하여 선미선형을 선정하였으며, 자유 수면에서 모델의 하부까지의 깊이는 동일하게 적용하였다. 선저가 끝단에서 트랜섬 선미형상에 의해 급격한 각도를 이루는 지점에서 상하로 맥동하는 유동특성이 나타나며, 각도가 증가 할수록 와의 형태가 작아져 난류의 발생이 감소하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.3
• /
• pp.408-418
• /
• 1999

Incompressible flow inside a circular cylinder Including periodically oscillating free surface waves was studied primarily by using a numerical method. We developed a finite difference scheme based on the MAC method applicable to three-dimensional free-surface flows, and applied it to the present flow model to study tho flow characteristics as well as the fluid stirring. To verify the validity of our scheme, we performed a simple experiment for flow visualization. We found that the numerical results show a reasonable agreement with the observed flow patterns.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1574-1579
• /
• 2004

A simultaneous measurement system that can analyze the flow-structure interactions(FSI) has been constructed and analyses on the flow field and the motion field of a floating cylinder was made. The three-dimensional vector fields around the cylinder are measured by 3D-PTV technique while the motion of the cylinder forced by the flow field is measured simultaneously with a newly developed motion tracking algorithm(bidirectional tracking algorithm). The cylinder is pendant in the working fluid of a water channel and the surface of the working fluid is forced sinusoidal to make the cylinder bounced. The interaction between the flow fields and the cylinder motion is examined quantitatively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1255-1261
• /
• 2004

A variational approximation procedure is introduced to study the contact stresses between a representative asperity and a feature generally happening in superfinishing processes such as FAM. After a description of the model under consideration is presented, a system of governing equation for the model is derived fullowed by the assumptions made in order to make progress in model development. Final computation is made to evaluate contact stresses on an elastic asperity tip in small scale in size and a computer simulation is performed for detailed surface profile variations on a representative feature. Numerical results are presented along with a discussion of the conclusions that can be drawn from this analysis.

• Journal of the Korean Society of Visualization
• /
• v.6 no.2
• /
• pp.28-32
• /
• 2008

Contrary to the flow rate in fully filled pipe flows, the flow rate in partially filled pipe flows is significantly influenced by the variation of water level, channel slop, and so on. The major difference in these two flows results from the existence of a free surface. To make it clear, in the present study, a similarity of the velocity profile in a partially filled circular pipe has been investigated according to the water level. A particle image velocimetry (PIV) technique was applied to measure the three-dimensional velocity profiles. As a result, there is found a similarity of the velocity profile near the central region. However, near the side wall, the similarity is broken due to the interaction between the wall and the free surface.