• 한국분무공학회지
• /
• 제8권1호
• /
• pp.29-36
• /
• 2003

Spray characteristics on diesel- water emulsion are analyzed in high pressure injection for several variables such as water content, injection pressure. Spray Patterns were visualized under various water content and injection pressures. Spray tip penetration was increased and spray angle decreased in accordance with increasing of water content. But these characteristics were enhanced with increase of injection pressure to high pressure.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.7-12
• /
• 2005

In order to analyze the microscopic spray characteristics of free spray in ultra high pressure region, the droplets size and velocity of free spray injected under atmosphere condition were measured by PDPA. As injection pressure became ultra high pressure, the droplets size was decreased continuously due to the increase of mutual reaction between droplets and air. But the decreasing rate became moderate. The velocity was increased until 250 MPa, and then decreased over that of injection pressure. It was seemed that the droplet size was similar in range of $280\~350\;MPa$, but increased in 414 MPa, even though injection pressure was increased. The microscopic spray characteristics of free spray got worse in 414 MPa.

• 수산해양기술연구
• /
• 제19권1호
• /
• pp.40-45
• /
• 1983

전자식전발분사노즐로 급속압축장치 내에서 실현한 축대칭 자유분무.화염에 고속도 사진의 화상해석을 적용하여 다음과 같은 결론을 얻었다. 1. 고속도 사진의 화상해석에 의해 구한 디이젤분무의 축방향의 연료농도분포는 분무의 선단부를 제외하면 준정상이론에 의한 분포와 정성적으로 일치한다. 2. 화염중심축방향의 그을음 농도는 연과의 농도가 비교적 낮은 분무의 선단부에서 높은 농도를 나타내며, 그 농도는 거의 분사종료시에 최대로 되어, 그 후 시간경과에 따라 저하한다. 3. 양파모델을 축대칭 분무.화염에 적용하여 분무.화염내부의 반경방향의 그을음 농도와 연료농도분포를 비교해 보면 그을음 농도의 가장 높은 부분은 연료농도가 가장 높은 중심부보다 화염반경의 2/3의 위치에서 최대로 되었다

• 한국분무공학회지
• /
• 제7권4호
• /
• pp.16-22
• /
• 2002

The characteristics of free spray with ultra injection pressure was analyzed to clear the limit pressure of diesel engine. To obtain final goal, ultra high pressure injection equipment was developed, spray patterns were visualized under various ultra injection pressures. Spray penetration and spray width, volume and entrained air mass were increased with the increase of injection pressure. Sauter mean diameter and injection durstion wert decreased. But over 3,000bar of ultra injection pressure region the rates of increase show almost similar and finally the reversed tendencies at 4,140bar.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.410-415
• /
• 2000

A diesel engine is one of the major prime movers to its high thermal efficiency. But due to the recent attention far the environmental pollution, the emissions of diesel engine became to a important problem. So it is needed to understand the characteristics of diesel spray injected into a combustion chamber. The factor which controls the diesel spray are the injection pressure, the nozzle diameter, the impinging angle and the variation of pressure and temperature. In this paper, experiments were conducted far the variation of the environmental temperature(273k, 373k, 573k), free spray and impinging spray. And the notions of penetration, spray angle, axial distance for free spray, and axial distance, spray thickness from impinging wall fur impinging spray.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.454-459
• /
• 2000

Diesel engine which has high thermal efficiency is one of the major movers. Recently, as people pay attention to the environmental pollution, the emission of Diesel engine becomes an important problem. So it is needed to understand the characteristics of diesel fuel spray injected into a combustion chamber to reduce the emission. The factors which control the diesel fuel spray are the injection pressure, the nozzle diameter, the impinging angle and the variation of an ambient pressure and temperature. In this paper, the experiments were conducted in the free spray and the impinging spray with various ambient temperatures(273K, 373K, 573K). And the behaviors of the diesel fuel spray, such as penetration, spray angle and axial distance in the free spray and axial distance and spray thickness in the impinging spray were studied.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.946-951
• /
• 2001

This experimental study is to investigate the intermittent spray characteristics of a pintle nozzle. High speed camera used in this expreiment with 9000fps. The factor, which controls the diesel spray, is the Injection pressure, ambient pressure and ambient temperature. In this paper, experiments were conducted free spray for the ambient pressure(3, 4, 5Mpa), nozzle Injection pressure(10, 14, 18MPa) and ambient temperature(293, 473K). With the higher opening pressure, the spray tip velocity and spray penetration increases while the spray angle decreases, On the other hand, With the higher ambient pressure, the spray angle increase while the spray tip penetration and spray tip velocity decrease. also, With the higher ambient temperature, the spray penetration decrease while the spray angle decrease.

• 한국자동차공학회논문집
• /
• 제13권3호
• /
• pp.131-137
• /
• 2005

Ultra high pressure injection equipment was developed to estimate and analyze the spray characteristics in ultra high pressure injection. Spray patterns were visualized by schlieren method and analyzed in ultra high pressure. Spray tip penetration, spray thickness, spray volume, and entrained air mass increased with the increase of the injection pressure. But over 2,800 bars of the injection pressure region, it was shown that the rate of improvement was not increased remarkably ,and the spray characteristics such as spray penetration, volume, and entrained air mass were reversed and got worse at 4,140 bars.

• 동력기계공학회지
• /
• 제15권3호
• /
• pp.5-11
• /
• 2011

디젤기관의 경우는 종래부터 직분식이 주류를 이루었고, 근래에는 분사압력의 고압화가 진행중이다. 분사압력의 고압화에 의해 연소효율의 향상 및 배출가스중의 입자상물질(PM:Particulate Matter)의 저감을 유도하고 있으나, 연소가스의 고온화로 인해 질소산화물(NOx:Nitrogen Oxides)은 증가한다. 따라서, 분사기간의 지연(Retard)이나 파일럿분사(Pilot injection)등의 혼합기제어에 의해 질소산화물의 저감을 꾀하고 있다. 이와 같이 디젤기관에 있어서도 혼합기 형성의 최적화에 의한 연소제어를 시도하는 수법이 중시되고 있고, 이를 위해서는 디젤분무 구조에 기초한 혼합기의 형성기구에 대한 규명이 매우 중요하다. 그러므로 본 연구에서는 보다 고도의 혼합기형성 제어를 위한 기초연구로서 고온 고압장에서의 증발디젤자유분무구조를 해석하였으며, 계측영역은 연료와 주위기체와의 혼합이 활발히 진행되는 분무의 하류영역으로 설정하고, 입자화상속도측정법(particle Image Velocimetry:PIV)을 이용한 분무의 유동해석을 기초로 증발 디젤분무의 구조 해석을 행하였다. 실험조건으로서 분사압력을 72MPa, 112MPa로 각각 변화시켰다.

• 에너지공학
• /
• 제3권1호
• /
• pp.54-61
• /
• 1994

계단형태의 고온발생장치로서, 고온의 흐름을 형성하고 난류유동이 없이 일정한 혼합기류를 만들 수 있는 2단격막구조 충격파관 장치를 이용하여, 혼합을 동반하지 않는 분무의 착화과정에 관한 실험을 수행하였다. 본 실험에서는 충격파관 속에 하향으로 설치된 초음파 분무기에 의해 자유낙하 상태에 있는 예혼합 분무주를 만들어서 반사충격파에 의해 순간적으로 단열압축시켜서 착화 현상을 관찰하였다. 고온영역과 저온영역에서 얻어진 활성화에너지는 큰 차이가 나며 본 연구에서 얻은 착화지연의 실험결과는 통상의 분무착화 실험인 전기로법, 급속압축기법, 고온기류속에 연료를 분사하는 방법과 다른 현상을 보였다. 그 대표적인 결과에 대한 예로는 착화지연에 대한 압력 의존성과 연료분사율의 영향이 일반적인 분무의 결과에 비해 적게 나타났다.