• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.666-673
• /
• 2013

This paper proposes the performance evaluation test of attitude heading reference system (AHRS) suitable for small high speed autonomous underwater vehicle(AUV). Although IMU can provides the detail attitude information, it is sometime not suitable for small AUV with short operation time in view of price and the electrical power consumption. One of alternative for tactical grade IMU is the AHRS based micro-machined electro mechanical system(MEMS) which can overcome many problems that have inhibited the adoption of inertial system for small AUV such as cost and power consumption. A cost effective and small size AHRS which incorporates measurements from 3-axis MEMS gyroscopes, accelerometers, and 3-axis magnetometers has been developed to provide a complete attitude solution for AUV and the attitude calculation algorithm is derived based the coordinate transform equation and Kalman filter. The developed AHRS was validated through various performance tests as like the magnetometer calibration, operating experiments using land mobile vehicle and flight motion simulator (FMS). The test of magnetometer calibration shows the developed MEMS AHRS is robust to the external magent field change and the test with land vehicle proves the leveling error of developed MEMS AHRS is below $0.5^{\circ}/hr$. The results of FMS test shows the fact that AHRS provides the measurement with $0.5^{\circ}/hr$ error during 5 minutes operation time. These results of performance evaluation tests showed that the developed AHRS provides attitude information which error of roll and pitch are below $1^{\circ}$ and the error of yaw is below $5^{\circ}$ and satisfies the required specification. It is expected that developed AHRS can provide the precise attitude measurement under sea trial with real AUV.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.26 no.2
• /
• pp.76-82
• /
• 2018

A test simulator is needed to develop a fuel quantity measurement system that takes into account the roll and pitch motion of the aircraft. In this paper, we develop a test simulator that consists of attitude simulation equipment, fueling equipment, and data storage equipment. The attitude simulation equipment simulates the aircraft attitude. It is manufactured to operate pitch angle and roll angle movement. The fueling equipment supplies fuel to the supplementary fuel tank. The data storage equipment collects and stores the measured data. We also develop an automation software that operates the test simulator and collects data automatically. The test simulator has been automated to prevent testers from being exposed to toxic fuel. Through automation software, the collection period is reduced by one quarter compared to manual collection. The developed fuel quantity measurement system is verified through the test simulator.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.11
• /
• pp.927-933
• /
• 2020

This paper presents a fuel quantity measurement system (FQMS) for an aircraft supplementary fuel tank considering the change of aircraft attitude. The developed FQMS consists of fuel sensors, a signal process unit, an indicator and a software to estimate the fuel quantity from the sensor data. To replicate the change of the roll and pitch attitude on the ground, the test simulator is developed in this work. Using the test simulator, the sensor data at various fuel quantities, roll and pitch angles are automatically measured to build a training data set. The data-driven software to estimate the fuel quantity is then developed using a trilinear interpolation method with the training data set. The developed FQMS is verified by investigating the fuel estimation error of the test data set that we know the true values. Through the test, it is confirmed that the error of the developed FQMS system satisfies the criteria of TSO-C55 document.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.35-38
• /
• 2003

The purpose of this work is to introduce the 1-N grade thruster development program for attitude control of satellites and lunch vehicle systems. Characteristics of the thruster and its performance have been evaluated through hot-firing test of small liquid engine inside a vacuum test cell. Performance evaluation of thruster were made with a variation of propellant injection pressure at steady state and pulse firing mode, respectively. Also hot-fire test system and test procedure are briefly described, too.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.177-182
• /
• 1996

Remote nuclear cask handling device (RNCHD)는 사용후 핵연료cask의 원격 조작에 있어서 안전성과 성능을 향상을 목적으로 한다. RNCHD의 한부분인 grapple은 사용후 핵연료cask의 이동 및 수송 또는 용기뚜껑의 개폐를 위하여 cask의 벽에 대각선으로 돌출되어있는 두 개의 trunnion에 삽입되어야한다. 그러나 trunnion으로의 grapple 삽입은 용기중심과 grapple 장치 중심사이의 위치와 방향편차 때문에 어렵게된다. 인공신경망은 grapple에 설치된 광전센서를 사용하여 용기의 중심으로 부터 grapple 장치의 상대적 위치를 계측하기위해 사용된다. 인공신경망 학습은 광전센서값과 grapple의 상대적 위치와 방향사이의 함수적 관계를 추론하기 위해 수행된다. 이렇게 측정된 RNCHD의 중심위치는 grapple의 자세를 맞추기 위한 제어입력값으로 제공된다. 인공신경망 학습을 위한 데이터는 grapple 장치와 trunnion을 모사한 1/2 스케일의 실험장치를 사용함으로써 얻어진다. 학습된 인공신경망은 학습에 사용 안된 센서입력값, 즉 새로운 grapple의 위치에 대해서도 정확성을 가지고 grapple 장치의 위치와 방위를 측정할 수 있었다.

• Journal of Aerospace System Engineering
• /
• v.13 no.3
• /
• pp.23-31
• /
• 2019

The design requirements of modern satellites vary depending on the purpose of operation. Like conventional medium and large-scale satellites, small satellites which operate on low orbit may also serve military purposes. As a result, there is increased demand for high-resolution photos and videos and multi-target observation becomes important. The most important design parameter for multi-target observation is the satellites' maneuverability. For increased maneuverability, the miniaturization is required to increase the stiffness of the satellite as this decreases the mass moment of inertia of the satellite. In the case of a solar panel having relatively low stiffness compared to the satellites' body, vibrations are generated when the attitude maneuver is performed, which greatly influences the image acquisition. For verification of such vibrational characteristics, the satellites is modeled as a reduced model, and experimental zig for simulating attitude maneuver is introduced. A rigidity simulator for simulating the stiffness of the satellite is also proposed. Additionally, the objective of the experimental method is to simulate the maneuvering angle of the satellite based on the winding length of the wire using a step motor, and to experimentally verify the vibration characteristics of the satellite body and the solar panel generated during the maneuvering test.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.401-405
• /
• 2017

Continuous variable thrusters require precise thrust control to change the position or attitude of the aircraft and to control the pressure inside the combustion chamber. For this purpose, the thrust is adjusted by moving the pintle structure near the nozzle neck inside the combustion chamber by moving the pintle structure forward and backward, and the actuator is used to move the pintle structure. In this paper, we developed a actuator system for continuous variable thruster and load test system to simulate the load under operating conditions. Also, the performance test of the actuator was performed using the developed load test system

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.31-31
• /
• 1998

위성체의 보조추진시스템은 임구궤도까지의 궤도진입 및 임무궤도상에서의 속도 또는 자세제어에 필요한 임펄스를 제공한다. 단일하이드라진 추력기는 하이드라진(H$_2$H$_4$)과 자발적 촉매(Shell 405)의 발열 및 흡열 열분해 반응에 의해 발생하는 질소($N_2$), 수소(H$_2$), 암모니아(NH$_3$), 혼합가스를 노즐을 통해 방출하므로써 요구되는 impulse를 얻는다. 단일하이드라진 추력기 설계는 주입기, 촉매대, 노즐과 기타 설계 형태에 따른 다지관, 링, 스크린, 지지판 등의 부수적인 부품으로 구성된다. 추력기 제작 과정은 크게 piece-parts 기계가공, HEA(Head End Assembly)와 TCA(Thrust Chamber Assembly)로 구성되고 각 세부공정마다 전수시험 및 검사를 가진다. 연소시험설비는 최소 모사진 공 수준이 고도 100,000 ft(8.4 torr)를 만족시킬 수 있는 진공설비, 시험제어부, 성능변수 측정 및 처리부, 추진제 가압 공급부, 기타 환경 안전 및 부대 설비로 구성된다. 추력기 연소성능시험 절차는 추진제 충전 및 오염 여부 표본 검사, 가압 및 공급 라인 이상여부 확인, 추력기 장착, 추진제 가압 및 공급, 시험장치 보정, 진공 모사 및 연소성능시험, data 처리 등으로 구성된다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.8-23
• /
• 1997

Steady and unsteady numerical simulations are conducted for the comparison with the experiments performed to investigate the ram accelerator flow field by using an expansion tube facility in Stanford University. Wavier-Stokes equations for chemically reacting flows are analyzed by fully implicit and time accurate numerical methods with Jachimowski's detailed chemistry model for hydrogen-air combustion involving 9 species and 19 reaction steps. Although the steady state numerical simulation shows a good agreement with the experimental schlieren and OH PLIF images for the case of $2H_2$＋$O_2$＋$17N_2$ fails in reproducing the combustion region behind the shock intersection point shown in the case of $2H_2$＋$O_2$＋$12N_2$ mixture. Therefore, an unsteady numerical simulation is conducted for this case and the result shows all the detailed flow stabilization process. From the result of unsteady numerical simulation, the experimental result seems to be an instantaneous state during the flow stabilization process. The combustion behind the shock intersection point is the result of a normal detonation formed by the intersection of strong oblique shocks that exist at early stage of the stabilization process. At final stage, the combustion region behind the shock intersection point disappears and the steady state result is retained. The time required for stabilization of the reacting flow in the model ram accelerator is found to be very long in comparison with the experimental test time.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.7
• /
• pp.594-599
• /
• 2017

In this thesis, the development and the verification of the test-aid are described, providing various attitude errors through the electric stimulus to the Sun sensor. This test-aid for 2-axis analogue Sun sensor is used for polarity test in the assembly stage for GK2 satellite. The test-aid used for GK2 satellite is for COMS satellite and, due to the failure risk, manufactured by domestic company. The characteristics of the COMS test-aid used for GK2 satellite and the manufactured test-aid are showed with similar through the several tests. In this thesis, there are conformed the capability for replacing of test-aid because the characteristics of the manufactured test-aid is acquired same as that of the COMS test-aid using the controller tuning functions.