• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.143-150
• /
• 2000

Depending upon the combination of tolerances specified in the standards on bolt, nut and washer for high tension bolt sets, there arises center-to-center deviation between bolt and washer. This deviation nay cause loss of effective contact area between nut- and washer-faces, which leads to some dispersion of the torque coefficient K. By adapting circular arc surface instead of flat surface for the nut, it is shown through numerical analyses that the dispersion of the torque coefficient can be minimized. In this way, optimum radius of curvature of the nut bearing surface is proposed.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.243-250
• /
• 2000

The mechanical behavior of the underground box culvert constructed by the open cut method depends mainly on the earth pressure acting on it. In this study, the earth pressure on the underground box culverts constructed by the open cut method during and after the construction sequence was numerically analysed by using FLAC. The results are compared with those of the Marston-Spangler's theory, silo theory, and the model tests. The results showed that the vertical earth pressure on the upper slab of the box structure was not uniform. It was as large as the overburden in the middle part of the slab but was smaller or larger than that at its end part depending on the slope of the excavation, the depth of the cover, and the width of the side refill. The horizontal earth pressure on the side wail was much smaller than the earth pressure at rest and grew nonlinearly with the depth.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.199-199
• /
• 2013

최근 단파장 광전 소자와 고출력 고주파 전자 소자에 대한 수요 때문에 넓은 밴드갭 에너지를 갖는 반도체에 관심이 많다. 이중에서, ZnO는 우수한 화학 및 역학적 안정성, 수소 플라즈마 내구성과 저가 제조의 장점 때문에 광전자 소자 개발 분야에 적합한 산화물 투명 전극으로 관심을 끌고 있다. 불순물이 도핑되지 않은 ZnO는 본질적으로 산소 빈자리 (vacancy)와 아연 격자틈새 (interstitial)와 같은 자체의 결함으로 말미암아 n형의 극성을 갖기 때문에, 반도체 소자로 응용하기 위해서는 도핑 운반자의 농도와 전도성을 제어하는 것이 필요하다. 본 연구에서는 박막 제조시 제어성, 안정성과 용이하게 성장이 가능한 졸겔 (sol-gel) 방법을 사용하여 사파이어와 석영 기판 위에 Cu가 도핑된 ZnO 박막을 성장시켰으며, 그것의 구조, 표면 형상, 평균 투과율, 광학 밴드갭 에너지를 계산하였다. 특히, Cu의 몰 비를 0, 0.01, 0.03, 0.05, 0.07, 0.1 mol로 변화시키면서 ZnO:Cu 박막을 성장시켰다. ZnO:Cu 졸은 zinc acetate dihydrate, 2-methoxyethanol (용매), momoethanolamine (MEA, 안정제)을 사용하여 제조하였다. 상온에서 2-methoxyethanol과 MEA가 혼합된 용액에 zinc acetate dihydrate (Zn)을 용해시켰다. 이때 MEA와 Zn의 몰 비는 1로 유지하였다. 이 용액을 $60^{\circ}C$ 가열판 (hot plate)에서 24 h 동안 자석으로 휘젓으며 혼합하여 맑고 균일한 용액을 얻었다. 이 용액을 3000 rpm 속도로 회전하는 스핀 코터기의 상부에 장착된 사파이어와 석영 기판 위에 주사기 (syringe)를 사용하여 한 방울 떨어뜨려 30 s 동안 스핀한 다음에, 용매를 증발시키고 유기물 찌꺼기를 제거하기 위하여 $300^{\circ}C$에서 10분 동안 건조시킨다. 기판 위에 코팅하는 작업에서 부터 건조 작업까지를 10회 반복한 다음에, 1 h 동안 전기로에 장입하여 석영 기판 위에 증착된 시료는 $550^{\circ}C$에서, 사파이어 기판은 $700^{\circ}C$에서 열처리를 수행하였다. Cu의 몰 비 0, 0.01, 0.03, 0.05, 0.07, 1로 성장된 ZnO:Cu 박막에 대한 x선 회절 분석의 결과에 의하면, 모든 ZnO:Cu 박막의 경우에 관측된 34.3o의 피크는 ZnO (002) 면에서 발생된 회절 패턴을 나타낸다. 이것은 JCPDS #80-0075에 제시된 회절상과 일치하였으며, ZnO:Cu 박막이 기판에 수직인 c-축을 따라 우선 배향됨을 나타낸다. 사파이어 기판 위에 증착된 박막의 경우에, Cu의 몰 비가 점점 증가함에 따라(002)면 회절 피크의 세기는 전반적으로 증가하여 0.07 mol에서 최대를 나타내었으나, 석영 기판 위에 증착된 박막의 경우에는 0.05 mol에서 최대를 보였다. 외선-가시광 분광계를 사용하여 서로 다른 Cu의 몰 비로 성장된 ZnO:Cu 박막에서 광학 흡수율 (absorbance) 스펙트럼을 측정하였으며, 이 데이터를 사용하여 평균 투과율을 계산한 결과, 투과율은 Cu의 몰 비에 따라 현저한 차이를 나타내었다. Cu의 몰 비가 0.07 mol일 때 평균 투과율은 80%로 가장 높았으며, 0.03 mol에서는 30%로 최소이었다. 광학밴드갭 에너지는 Tauc 모델을 사용하여 계산하였고, 결정 입자의 형상과 크기와의 상관 관계를 조사하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.1
• /
• pp.13-23
• /
• 2015

The paper experimentally deals with the radial in-plane vibration characteristics of disk-shaped piezoelectric transducers. The radial in-plane motion, which is induced due to Poisson's ratio in the piezoelectric disk polarized in the thickness direction, was measured by using an in-plane laser vibrometer, and the natural frequencies were measured by using an impedance analyzer. The experimental results have been compared with theoretical predictions obtained by simplified theoretical and finite-element analyses. It appears that the fundamental mode of a piezoelectric disk transducer is a radial mode and its radial displacement distribution from the center to the perimeter is not monotonic but shows maximum slightly apart from the perimeter. The theoretically-calculated fundamental frequencies agree well with the finite-element results for small thickness-to-diameter ratio, and they are accurate within 7 % error for the ratio up to 0.4.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.3
• /
• pp.399-407
• /
• 2002

A three-dimensional method of analysis is presented for determining the free vibration frequencies and mode shapes of hollow bodies of revolution (i.e., thick shells), not limited to straight line generators or constant thickness. The middle surface of the shell may have arbitrary curvatures, and the wall thickness may vary arbitrarily. Displacement components$U_\Phi, U_z, U_\theta$ in the meridional, normal and circumferential directions, respectively, are taken to be sinusoidal in time, periodic in$\theta$, and algebraic polynomials in the$\Phi$and z directions. Potential(strain) and kinetic energies of the entire body are formulated, and upper bound values of the frequencies are obtained by minimizing the frequencies. As the degrees of the polynomials are increased, frequencies converge to the exact values. Novel numerical results are presented for two types of thick conical shells and thick spherical shell segments having linear thickness variations. Convergence to four digit exactitude is demonstrated for the first five frequencies of both types of shells. The method is applicable to thin shells, as well as thick and very thick ones.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.4
• /
• pp.112-131
• /
• 2021

The Gwanghwamun Gate of the Gyeongbokgung Palace was established in 1866 when Heungseon Daewongun rebuilt the Gyeongbokgung Palace. In Gwanghwamun, a large platform, woldae was established to reveal its hierarchy. The Gwanghwamun Woldae was equipped with stone railings on the left and right sides, fishing routes in the center, and stairs and slopes to the south. The Yongdu Stone was installed on the south side of the slope, which connected to the woldae, to express the path of the king in a formative manner. The Woldae King Road in Gwanghwamun was expanded in 1915 as the Joseon Promotion Conference was held at the Gyeongbokgung Palace and the woldae was destroyed around 1925. Since then, the figure has not been found since the time before the Gwanghwamun Gate. In the Donggureung royal tombs, there are many stones that are not placed in the royal tombs, including voussoir arch stones, Munsojeon Gugi-bi, as well as Nangan-Seokju, Dongja-seok, and Juk-seok, which are elements of the stone railings. These stone railings and Yongdu-seok are seen as stone objects of the Gwanghwamun Woldae, which can be found through the analysis of the style of the times and comparison with modern photographs.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.1
• /
• pp.59-66
• /
• 2022

In order to solve the problem of urban traffic congestion, Urban Air Mobility (UAM) concept using Electric Vertical Take-off and Landing (eVTOL) aircraft has been gaining popularity, and many domestic and international studies are underway. However, since these aircraft inevitably fly over densely populated areas, it is essential to ensure safety, which starts with accurately analyzing the crash risk. In this paper, the locations and impact speeds of crash are computed using six degree-of-freedom simulations of an eVTOL aircraft in a fixed-wing mode. System malfunction was modeled by a sudden loss of thrust with control surfaces being stuck during cruise. Because most of these eVTOL aircraft are still under development, a methodology of constructing a six degree-of-freedom dynamics model from generic specification is also developed. The results show that the crash locations are highly concentrated right under the aircraft within a square that has an edge length similar to the cruise altitude. Speed distribution is more complicated because almost identical crash locations can be achieved by two very different paths resulting in a large variation in the speeds.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.3
• /
• pp.224-231
• /
• 2010

Purpose: This study was to investigate how the crestal module design could affect the level of marginal bone stress around dental implant. Materials and methods: A submerged implant of 4.1 mm in diameter and 10 mm in length was selected as baseline model (Dentis Co., Daegu,Korea).A total of 5 experimental implants of different crestal modules were designed (Type I model : with microthread at the cervical 3 mm, Type II model : the same thread pattern as Type I but with a trans-gingival module, Type III model: the same thread pattern as the control model but with a trans-gingival module, Type IV model: one piece system with concave transgingival part, Type V model: equipped with beveled platform). Stress analysis was conducted with the use of axisy mmetric finite element modeling scheme. A force of 100 N was applied at 30 degrees from the implant axis. Results: Stress analysis has shown no stress concentration around the marginal bone for the control model. As compared to the control model, the stress levels of 0.2 mm areas away from the recorded implant were slightly lower in Type I and Type IV models, but higher in Type II, Type III and Type V models. As compared to 15.09 MPa around for the control model, the stress levels were 14.78 MPa, 18.39 MPa, 21.11 MPa, 14.63 MPa, 17.88 MPa in the cases of Type I, II, III, IV and V models. Conclusion: From these results, the conclusion was drawn that the microthread and the concavity with either crestal or trans-gingival modules maybe used in standard size dental implants to reduce marginal bone stress.

• Cartoon and Animation Studies
• /
• s.9
• /
• pp.127-142
• /
• 2005

Not only in Korea but throughout the entire world millions of people are in contact with images. Images have become a medium through which to transmit anything from simple visualizations of moving images to knowledge and information. The age of the internet has arisen thanks to scientific development, and the internet generation's acquisition of information is continuously becoming faster. The spectators, ufo must choose amongst the excessive amount of available information, are changing along with it just as quickly. The method of visual transmission has changed to match the demands of the fast-changing pace of the new generation. In order to receive an instantaneous selection amongst much information, the primary requisite is attracting one's attention, and then presenting a corresponding feeling of satisfaction. The early stages of film arose from the desire to capture one's actual situation as it realty is. Unsatisfied with the still picture, people developed the motion picture. Research has succeeded in reproducing 3-dimensional images more realistic than the actual image we perceive as a result of the difference in visual perspective of both eyes and their response to rays of light From color film to 3-dimensional pictures, people enjoy the magnificent results of this. All fields within the category of film are continuously studying the human desire to pursue their visual side, namely the pursuit of visual images with a maximum sense of reality. The images that millions of people around the world see now are flat. The screen's depth and optical illusions effectively give a sense of reality while conveying information. However, although the flat screen is able to create a sense of depth using the different visual perspective of each eye for the realization of a cubic effect, there are limitations. Entering the 21s1 century, there is a quickly-arising branch within the field of image media which seeks to overcome these limitations Although 3-dimensional images began in films, entering the latter half of the 20th century, due to development of 3-dimensional images using the mediums of the animation field, cellular phones, advertisement screens, television etc., without restriction is designated as 'image.'. With research having started around 1900 and continuing for over 100 years, we are now able to witness the popularization of 3-dimensional films happening before our very eyes. Within our own country, we can frequently see them at amusement parks and museums. In the future, through the popularization of HDTV etc., there is a good outlook for practical use of 3-dimensional images in televisions with advanced picture qualify as well as in other areas. Together with the international current, research on 3-dimensional films has been activated in Korea and is rising as a main current in the film industry. Within this context, the contents and understanding of 3-dimensional images must keep in step with the pace of technical advancements. In order to accelerate of development of film contents to keep in pace with technical developments, this dissertation presents the techniques and technical aspects of future developments, and shows the need to prepare in advance to make the field grow- and thereby avoid having a lack of experts and being conquered by other nations in the field - rather than only advancing the technical aspects and importing the contents. This dissertation aims to stimulate interest and continual research by progressive-thinking people related to the film industry. Part II looks into the definition and types of 3-dimensional motion pictures, the terminology, the fundamentals of image formation, current market fluctuations, and looks into 3-dimensional techniques which can be borrowed and introduced in 3-dimensional animations. Part III concerns 3-dimensional animated films. It analyzes 3-dimensional production techniques while using the introduction of specific animation techniques in the 2004 production Lee Sun Shin and Nelson - Naval Heroes 3-dimensional animation produced in 2004 by Clay & Puppet Stop-Motion Animation & Computer Graphic. Original Korean title: 해전영웅 이순신과 넬슨. as an example, and it also looks into how current film techniques used in animations can be applied in 3-dimensional films. Additionally, the actual stages of the various fields of 3-dimensional animations are presented. Given the current direction and advancement of 3-dimensional films making use of animations and the possible realization of this field, the author plans to weigh the development of this yet unexploited new market Not looking at the current progress of the field, but rather the direction of the hypothetical types of animation techniques, the author predicts the marketability and possibility of development of each area.