• Transactions of the Korean Society of Automotive Engineers
• /
• 제23권5호
• /
• pp.553-563
• /
• 2015

Reportedly the fatality rate from secondary collision is six times higher than the average fatality rate from all traffic accidents. So prevention of the secondary collision is attracting significant attention from automotive industries. However, the secondary collision prevention systems that have been developed are not considering possibility of brake actuator failure that can occur by the impact during the initial collision. In this paper, a new system has been developed that could prevent secondary collision even in case of brake actuator failure by taking advantage of still operating actuators. In this system, a steering control is performed for maintaining a lane by using linear quadratic regulator. Additionally, the system attempts differential brake control with the remaining braking capability to stop the vehicle in the shortest distance. Through simulation in various collision scenarios, the system has demonstrated significant potential of preventing secondary collision that could otherwise have resulted in severe fatality.

• International Journal of Highway Engineering
• /
• 제6권4호
• /
• pp.35-43
• /
• 2004

Skid resistance is an important factor that control braking distance and secure safety by preventing slipperiness between tire and pavement surface. Decrease of skid resistance at wet condition may cause fatal traffic accidents. Dirt materials such as sand and do-icings on the road surface also can be a factor for decrease skid resistance. This study makes an investigation into influence of skid resistance between varied cement concrete pavements about surface texturing method(transverse tining, longitudinal tining, exposed aggregate surface texturing method) and wearing condition of pavement surface texture(new constructed pavement's surface, wore pavement's surface) using accelerate concrete pavement wearing tester when remains of dirt material are obtained between tire and road surface on PCC pavement. As dirt material on road surface of concrete pavement, sand, calcium chloride and old oil were used with different amount of each cases.

• Journal of the Korean Geographical Society
• /
• 제28권3호
• /
• pp.200-212
• /
• 1993

Wholesaling is important industry that is remarkable by the function and characteristics of city. This paper aims at examing the recent changes in hierarchy of cities and city classifi-cation by wholesale activities in Korea. In order to grasp the stydy purpose, this paper is to analuze the changes of categories by wholesale industry, and to grasp the change in the city classification with city hierachy of wholesale sales in 1968, 1979, and 1991. The data were obtained from the statistics in the Census of Wholesale and Retail Trade published by the National Statistical Office, in 1969, 1981, and 1992. As the result of examination, the following finding were obtained: 1. Wholesaling has developed form that of production and consumption goods wholesale, especially 'Wholesaling of Farm Products, Foods and Beverages' to that of investment goods that is 'Wholesaling of Machinery and Equipment' and 'Wholesaling of Transport Equipment and Parts'. 2. Wholesaling has developed in the medium and small cities in 1970's, and in the larger cities in 1980's. And the concentration ratio of six larger cities were lower than another cities in terms of wholesale sales, especially Seoul and Pusan. 3. Recently with income increment and a purchasing power, city classification was changed by the increasing number of wholesale establi-shments of 'Automotive Parts and Tyres' in 1970's and of 'Office, Computing and Accounting Machines and Motor Vehicles' in 1980's.

• Elastomers and Composites
• /
• 제49권3호
• /
• pp.220-224
• /
• 2014

The tire tread is contacted with road surface directly. It gives significant effect on the breaking conditions, traction, noise and so on. The tread having grooves with complex geometry is molded by shaping process. The flow behavior of tread rubber in a mold affects the quality of the tread and it leads to the running performance of automobile. In this study, the flow behavior of rubber in shaping process has been investigated by computer simulation. The objective of flow simulation is the design of tread shape based on the contact of rubber on the mold surface and flow behavior of rubber. Different sequences of contact of rubber on the mold surface and flow behavior of rubber are observed according to the shape of tread on the mold surface. It was verified that the shape of tread gives significant effect on the flow behavior of rubber. Different flow behaviors of rubber and sequential contact of rubber to the mold surface were observed according to the shape of tread on the mold surface. Therefore, we have identified that the shape of tread give a change in the flow behavior of rubber.

• Journal of Practical Engineering Education
• /
• 제6권2호
• /
• pp.105-110
• /
• 2014

In this work, mechanical characteristics of titanium diaphragm have been studied as a potential robust substrate and a diaphragm material for automotive tire pressure sensor. Lamination process techniques combined with traditional micromachining processes have been adopted as suitable fabrication technologies. To illustrate these principles, capacitive pressure sensors based on titanium diaphragm have been designed, fabricated and characterized. The fabrication process for micromachined titanium devices keeps the membrane and substrate being at the environment of 20 MPa pressure and $200^{\circ}C$ for a half hour and then subsequently cooled to $24^{\circ}C$. Each sensor uses a stainless steel substrate, a laminated titanium film as a suspended movable plate and a fixed, surface micromachined back electrode of electroplated nickel. The finite element method is adopted to investigate residual stresses formed in the process. Besides, out-of-plane deflections are calculated under pressures on the diaphragm. The sensitivity of the fabricated device is $9.45ppm\;kPa^{-1}$ with a net capacitance change of 0.18 pF over a range 0-210 kPa.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제18권6호
• /
• pp.431-437
• /
• 2017

In this study, based on the RPS algorithm, the application results to an electrically controlled suspension system using previewed road information are presented. Reducing the excessive vibration induced by a disturbance transmitted to the system and secure its stability is a major issue. In particular, in the automotive industry, the demand is constantly being raised. A typical external disturbance causing vibration and instability of a vehicle is an irregular roadway surface that contacts a running vehicle tire. Therefore, obtaining such profile information is an important process. The RPS algorithm using a multi sensor system was constructed and implemented in a real car. Through experimental work using the RPS system included non-contact type optical sensors, it could robustly reconstruct the road input profiles from the intermixed data onto the vehicle's dynamic motion while traveling at an uneven roadway surface. A controller with a preview control was designed in the framework of a semi-active suspension system based on the 7 degrees of freedom full vehicle model. The control performance of the system was evaluated through simulations and the results were compared with the passive vehicle condition. These results highlight the feasibility of the presented control frame.

• The Journal of the Acoustical Society of Korea
• /
• 제37권6호
• /
• pp.469-474
• /
• 2018

As urban population increases, research on urban environmental noise is getting more attention. In this study, we classify the abnormal noise occurring in traffic situation by using a deep learning algorithm which shows high performance in recent environmental noise classification studies. Specifically, we classify the four classes of tire skidding sounds, car crash sounds, car horn sounds, and normal sounds using convolutional neural networks. In addition, we add three environmental noises, including rain, wind and crowd noises, to our training data so that the classification model is more robust in real traffic situation with environmental noises. Experimental results show that the proposed traffic sound classification model achieves better performance than the existing algorithms, particularly under harsh conditions with environmental noises.

• Composites Research
• /
• 제26권4호
• /
• pp.223-229
• /
• 2013

Hybrid composite strut tower was designed to prevent permanent deformation of upper mount by the impact from the uneven road. When exceeding energy absorption capacity of tire and suspension systems, residual impact is delivered to upper mount. Especially, in case of using high-rigidity suspension system for high driving performance, the conventional strut tower can be easily deformed due to reduction of energy absorption capacity of suspension systems. In this study, optimal design of hybrid composite strut tower which made of back-up metal and carbon fiber reinforced composite was suggested by using finite element analysis, and low velocity impact test was performed to investigate their dynamic characteristics. Also, 3D measuring and ultra c-scanning methods were carried out to diagnose damages in the strut towers.

• Journal of the Korea Society of Computer and Information
• /
• 제13권1호
• /
• pp.65-73
• /
• 2008

The telematics data management deals with queries on stream data coming from moving cars. So the stream DBMS should process the large amount of data stream in real-time. In this article, previous research projects are analyzed in the aspects of query processing. And a hybrid model is introduced where query preprocessor is used to process all types of queries in one singe system. Decreasing cost and rapidly increasing Performance of devices may guarantee the utmost parallelism of the hybrid system. As a result, various types of stream DBMS queries could be processed in a uniform and efficient way in a single system.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.849-852
• /
• 2008

In the wheel tracking test to evaluate abrasion resistance for concrete surface coating materials applied parking lot, weight of the wheel, test temperature, scattered sand amount, wheel speed, etc. various test condition is used for reliable evaluating the abrasion resistance performance of surface coating materials and the results depends on the test condition. In this paper, we carried experimental study as following on abrasion resistance with 2kinds of different environmental conditions. - Commons : real car tire with 300kg of load, 5km/h of speed, 80,000 cycle. - Control A : no other deterioration condition - Control B : scattering 1.0g of sand per every 30rounds from 1m height.