• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.239-242
• /
• 2003

자동차 점화장치는 전원으로부터 공급된 낮은 전압을 점화코일을 통하여 연소실의 혼합기를 연소시키기에 충분한 고전압을 발생시키는 장치이며, 점화장치의 핵심은 점화코일이다. 이 점화코일은 절연성능이 우수한 절연재료가 사용되지만 고전압의 발생으로 점화코일 내부에서 일어나는 전기적 열화로 인해 누설전류가 흐르게 되어 전기적 고장을 초래할 수 있다. 이로 인하여 절연재료의 수명은 단축되며, 또한 점화코일에 전류가 흐름으로써 코일 내부에서 발생하는 온도변화에 따른 절연열화로 점화코일의 성능이 저하될 수 있다. 따라서 본 연구에서는 점화코일에 사용되고 있는 절연재료에 전압이 인가될 때 발생할 수 있는 비파괴검사의 일종인 부분방전 측정을 통하여 전압변화에 따른 에폭시 성형 점화코일의 위상각($\Phi$) - 방전전하량(q) - 발생빈도수(n)의 특성 변화를 조사하고 분석함으로써 점화코일의 수명을 예측하여 자동차 점화장치의 성능진단과 정보제공을 자동차 전기장치의 발전에 도움이 될 것을 기대하며, 온도상승에 따른 점화코일의 부분방전 특성을 실험하고 분석하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.11
• /
• pp.775-784
• /
• 2017

The purpose of this study was to analyse the basic data of the engine tuning inspection by confirming the working possibility of effective engine tuning and identifying the characteristics of tuned engine that are no problem with the safety operation and environment in a driving gasoline car. The effects of tuned engine on the characteristics of air/fuel ratio and performance at a wide range of engine speeds were experimentally investigated by the actual driving car with a four-cycle, four-cylinder DOHC, turbo-intercooler, water-cooled gasoline engine operating under four types of non-tuning, and tuning 2-1, 2-2 and 2-3. The tuned parts of engine in a driving gasoline car include the intake manifold, intake pipe, air filter, exhaust manifold, exhaust pipe and silencer. In this experiment, the air-fuel ratio and torque of both non-tuned and tuned engines that one person took on board in the car with a five-speed automatic transmission were measured by the chassis dynamometer(Dynojet 224xLC). It was found that the maximum torque of tuned engine in a driving gasoline car was increased by 103.68% on average, while the maximum output was increased by 119.68% on average in comparison to the non-tuned engine.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.6
• /
• pp.177-191
• /
• 2021

One of the major causes of serious air pollution worldwide is emissions from road transportation. A number of countries are working to reduce vehicle emissions, and the Seoul Metropolitan Government is also implementing active policies to reduce emissions by setting a target of 40% by 2030. Implementing these policies requires the introduction of practical indicators. Most of the domestic emissions are calculated by the emission coefficient, a function of speed at the National Institute of Environmental Research under the Ministry of Environment, but the dynamic variable speed is limited to being used as an indicator of the number of eco-friendly vehicles. Therefore, this study calculated the emission rates in Seoul using the vehicle registration data of Seoul and the vehicle inspection data from the Korea Transportation Safety Authority. The tendency of emissions was determined according to key variables such as vehicle type, fuel and mileage. Emissions were based on carbon monoxide, hydrocarbons, nitrogen oxides and particulate matter measured by vehicle inspection from the Korea Transportation Safety Authority. As a result, the emission rates showed a significant trend according to the model year and mileage. This can be used as a policy indicator to preferentially switch commercial vehicles with old model years and long mileage when switching eco-friendly vehicles in Seoul.

• Journal of Korea Society of Industrial Information Systems
• /
• v.7 no.5
• /
• pp.190-194
• /
• 2002

The aim of development is system having convenient, cheap, reliable and better good measurements. The cozy environments in auto and architects is essentiable requirements. This study focuses on system developments of test equipment for better performance of noise protection in automobiles. Sound cards using makes easily to acquire the sound in each room, especially reduced the complexities of the circuits. The developed system have easily been measured and have characteristics of rapid mecanical response. The menu of rough scan method makes efficiently to test the shielding performance of auto rubber in whole frequency scales.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.7
• /
• pp.23-30
• /
• 2014

"Cut off line" in automotive passing beam has very important safety function because it serves for headlamp aiming. Headlights that are aimed incorrectly will not only perform poorly but also offend oncoming traffic. In addition, an objective definition of cut off line in low beam is necessary, since a requirement for correct aiming of the beams is specified within all the existing regulations. Accordingly, headlight regulations are requirements that automobiles must satisfy in order to be sold in a particular country. In this study, a more advanced recognition method for the cut off lines of the various headlamps commonly used in Europe, North America, and domestic is suggested and a headlamp testing system is developed to adjust the beam to the country-specific regulation. This system uses image processing technology to detect the cut off lines in the beam patterns of halogen headlamps, high-intensity discharge headlamps, and light-emitting diode headlamps as well.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.513-518
• /
• 2019

The non-destructive testing equipment using an eddy current was developed to check for defect in the vehicle transmission component. A defect master sample was made to test all types of defects that occur in the component and also an eddy current detector was manufactured and used to test and detect all kinds of defects. In addition, testing was held against the actual defective items to investigate the cause and type of defects, and a comparative study was conducted based on results from the examination. The software system of the eddy current detector was developed so that even a non-specialist can make assessment of detect in the component from the test results displayed on the monitor.

• Journal of Auto-vehicle Safety Association
• /
• v.13 no.2
• /
• pp.24-29
• /
• 2021

In order to prevent automobile accidents internationally, advanced safety devices are actively being developed. Among them, Auto Emergency Brake (AEB) function and Forward Collision Warning (FCW), which are used to prevent or reduce frontal collision, have been studied for a long time, and are being researched by various manufacturers to develop better performance. In fact, in the case of large vehicles, it is mandatory for AEB to be installed in Korea. Accordingly, a variety of Vehicles equipped with AEB and FCW are coming out, and inspection of these mounting devices is a necessary system in the future. This study confirms how AEB and FCW are currently assessed in regulation and the New Car Assesment Program (NCAP), This is a basic study of the matters to be considered in preparing AEB and FCW inspection standard by checking the performance of vehicles equipped with forward collision protection and identifying the vehicle's sensitivity, range and speed of radar sensors, and target vehicles based on CAN communication data.

• The monthly packaging world
• /
• s.242
• /
• pp.100-109
• /
• 2013

해양수산부(장관 윤진숙)는 위험물의 분류기준을 국제기준과 동일하게 적용하고 위험물질 운송에 따른 안전성 제고를 위해 "위험물 선박운송 기준"을 개정하여 시행한다고 밝혔다. 개정된 기준은 국제적으로 적용되는 "국제해상위험물규칙"(IMDG Code)의 최근 개정내용을 반영하고, 위험물 및 화물구역의 종류별 방화장치 요건을 강화하여 위험화물로 인한 선박의 화재 및 폭발 사고가 감소될 것으로 기대된다. 특히, 위험물 운송 용기를 용기의 종류, 재료 및 형태별로 구분하고 외관, 구조 및 성능검사로 세분하여 위험물 용기 검사체계를 효율화함으로써 민원인의 편의를 도모하였으며, 또한, 국제기준에 따라 자동차를 일반선박이나 컨테이너에 수납하여 운반하는 경우 위험물로 분류되어 위험물수납 검사대상이 된다. 본 고에서는 "위험물 선박운송 기준" 일부 개정(안)에 대해 살펴보도록 한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.600-602
• /
• 2019

Metals are used in a variety of industrial sites and daily life. Metals are often used in machinery, automobile parts, wires, and robots. Metal causes small damage to the metal surface for a variety of reasons, such as the processing process and the user's operating environment. In this paper, phase detection for the inspection of defects in metals has been implemented. Using the electrical conductivity of metal, a circuit whose phase varies with the depth and size of the defect, and with the changed phase, the depth and size of the defect can be estimated.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.167-179
• /
• 1998

Todays in the field of lens makers, the technology machinery equipment and investment is shrunken by many factors. But much more decisive investment is wanted to strengthen competitiveness. Most of all, the technology of management and quality examination is important in the confidence of lens. So external and internal examination must be accomplished scientifically not by macrography but by the microscope and the computer. As the hardness examination of glass in the automobile, that of spectacle lens must not be harmful to the human body. All the raw material of spectacle lens is being imported for the lack of technology. To overcome these circumstances. We must establish the research institute that can develop the technology and must train a technical expert.