• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.96-96
• /
• 2004

고성능 섬유강화 복합재는 비강성과 비강도가 높고 내부식성과 피로특성이 우수하지만 외부에서 가해지는 하중에 의해 수지, 강화섬유와 수지와의 경계면, 적층 경계면 등에 육안으로 식별하기 어려운 손상이 유발될 가능성이 있으며 이로 인해 구조재로서의 역할을 하지 못하는 경우가 발생한다. 최근에는 외부하중으로 인해 복합재 구조재에 손상이 발생한 경우 자가치료제가 저장된 마이크로캡슐을 이용하여 손상을 보수하려는 시도가 행해지고 있다.(중략)

• Composites Research
• /
• v.28 no.6
• /
• pp.395-401
• /
• 2015

This study investigated the thermal stability of Grubbs' catalyst and its reactivity with self-healing agents for self-healing damage repair. Four types of Grubbs' catalyst supplied by manufacturers were considered and each catalyst was tested in as-received and grinded conditions. Four types of self-healing agents were prepared by varying the mixing ratio of dicyclopentadiene (DCPD) and 5-ethylidene-2-norbonene (ENB). Heat flows as a function of temperature were measured through a differential scanning calorimetry (DSC) to determine the thermal stability of catalysts. Reaction heats of self-healing agents with the catalyst were measured to evaluate the reactivity of the catalyst. For this evaluation, Fluka Chemika Grubbs' catalyst was used based on the maximum temperature and the time to reach the maximum temperature. According to the results, catalysts had different shapes depending on the manufacturer and the results showed that the smaller the size of the catalyst the higher the reactivity with self-healing agents. As the ENB ratio in self-healing agents increased, the maximum temperature increased, and the time to reach the maximum temperature decreased. As the amount of the catalyst increased, the maximum temperature increased, and the time to reach the maximum temperature decreased. Considering the thermal stability of the catalyst and its reactivity with the self-healing agent, combination of 0.5 wt% catalyst and the D3E1 self-healing agent was optimal for self-healing damage repair. Finally, as the thermal decomposition may occur depending on the environmental temperature, the catalyst must not be exposed to temperature higher than that is necessary to maintain the thermal stability of the catalyst.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.793-796
• /
• 2003

This study dealt with the manufacturing process of self-healing microcapsules for damage repair in polymeric composites. The microcapsule was consisted with a DCPD (dicyclopentadiene) as the healing agent and a urea-formaldehyde resin as the wall section. The size distribution of microcapsules were measured by a particle size analyzer using a laser diffraction technique. Thermal stability of microcapsules was investigated by using a TGA under continuous and isothermal heating conditions. According to the results, these microcapsules were verified to be to thermally stable and have a great potential to be applicable for damage repair in polymeric composites.

• Journal of the Korean Institute of Gas
• /
• v.20 no.4
• /
• pp.33-43
• /
• 2016

Grinding, weld deposition, type A sleeve, type B sleeve, composite sleeve, hot tapping and clamp are used as the method to repair the buried pipelines in the United States, UK and Europe. In the event of defect to the pipeline, they have repaired the pipeline through the fitness-for-service assessments. In addition, they have guidelines for the possible repair methods to apply to each type of damage, which is occurred due to the 3rd party construction or corrosion. According to the KGS FS551, Safety Validation in Detail including ECDA(External Corrosion Direct Assessment) as one method of integrity management should be carried out for the old pipeline which supply natural gas as the middle pressure in Korea. Where a defect on the pipelines is found, on the result of Safety Validation in Detail, the pipelines should be repaired or replaced by new piping. However, there are no guidelines or regulations regarding the repair and reinforcement of pipeline, so that, cutting the damaged pipeline and replacing it as a segment of new pipe is the only way in Korea until now. We have suggested pipeline repair methods including type A, B sleeve, composite sleeve, after the survey of foreign repair method and standards including the method of United States and the United Kingdom, and after analysis of the results on pipeline repair test including type A, type B sleeve and composite sleeve.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1997.11a
• /
• pp.35-50
• /
• 1997

쓰레기 매립장의 오수 침출 방지를 목적으로 그간 차수층이 시공되었으나 기존의 차수재는 그 성능상 많은 문제점을 내포하고 있었다. 이게 본 고에서는 '자가 형성' 및 '자가 치유'기능을 가진 SS/SH 차수층에 관하여 실내 시험 및 수도권 매립지(3공구)를 대상으로 현장 시험시공을 실시한 결과에 관해서 기술하였다. 두 시험을 통하여 SS/SH 차수층은 쓰레기 매립장 차수재로써 필요한 기준강도를 충족시키는가 하면 투수계수도 기준치를 만족시키는 낮은 수치를 나타내는 등 우수한 기능성을 충분하게 입증하였다. 무엇보다, 쓰레기 매립장에서 일반적으로 발생하는 차수층 손상에 대한 '탁월한 치유기능'을 가지고 있음으로 차수층 보수비가 전혀 필요없다는 점에서 대단히 경제적이라고 판단되었기에, 기능성과 경제성을 확보한 이 SS/SH 공법을 본공사에 적용할 수 있게 된 것이다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.4
• /
• pp.62-69
• /
• 2023

This study investigated the electromechanical properties of cement based smart repair materials (SRMs) according to the different amounts of fine steel slag aggregates (FSSAs). SRMs can self-diagnose the quality of repairing and self-sense the damage of repaired zone. The replacement ratios of FSSAs to sand for SRMs were 0% (FSSA00), 25% (FSSA25), and 50% (FSSA50) by sand weight. The electrical resistivity of SRMs generally decreased as the compressive stress of SRMs increased: the electrical resistivity of FSSA25 at the age of 7 hours decreased from 78.16 to 63.68 kΩ-cm as the compressive stress increased from 0 to 22.37 MPa. As the replacement ratio of FSSAs by weight of sand increased from 0% to 25%, the stress sensitivity coefficient (SSC) of SRM at the age of 7 h increased from 0.471 to 0.828 %/MPa owing to the increased number of partially conductive paths in the SRMs. However, as the replacement ratio of FSSAs further increased up to 50%, the SSC decreased from 0.828 to 0.649 %/MPa because some of the partially conductive paths changed to continued conductive ones. SRMs are expected to self-sense the quality and future damage of repaired zone only by measuring the electrical resistivity of the repaired zone in addition to fast recovery in the mechanical resistance of structures.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.262-265
• /
• 2004

This study focused on the introduction of the self-healing technique for polymeric composites and evaluated the healing efficiency through the interlainar fracture toughness tests. The DCPD and ENB were used for a healing agent and the Grubbs' catalyst as a catalyst. The healing efficiency was evaluated by the use of mode I and the mode n fracture toughnesses. According to the results, the DCPD-ENB mixture with a suitable ratio revealed better healing efficiency than DCPD only.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.5
• /
• pp.345-352
• /
• 2016

As aircrafts are being operated at high altitude, wing structures experience various fatigue loadings under cryogenic environments. As a result, fatigue damage such as a crack could be develop that could eventually lead to a catastrophic failure. For this reason, fatigue damage monitoring is an important process to ensure efficient maintenance and safety of structures. To implement damage detection in real-world flight environments, a special cooling chamber was built. Inside the chamber, the temperature was maintained at the cryogenic temperature, and harmonic fatigue loading was given to a wing structure. In this study, piezoelectric active-sensing based guided waves were used to detect the fatigue damage. In particular, a beamforming technique was applied to efficiently measure the scattering wave caused by the fatigue damage. The system was used for detection, growth monitoring, and localization of a fatigue crack. In addition, a sensor diagnostic process was also applied to ensure the proper operation of piezoelectric sensors. Several experiments were implemented and the results of the experiments demonstrated that this process could efficiently detect damage in such an extreme environment.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.309-314
• /
• 2004

This study focused on the introduction of damage repair for polymeric composite carbody. called selfing tech-healinique. using microcapsules loaded with the healing agent The manufacturing process for microcapsules with the healing agent was introduced and tile characteristics of microcapsules manufactured by varying with various manufacturing process variables were evaluated. The DCPD was used for the healing agent and microcapsules were made of urea-formaldehyde resin. The magnitude and the size distribution of microcapsules were measured by a particle size analyzer using laser diffraction technique. Thermal stability was investigated by using a TGA under continuous and isothermal heating conditions for the healing agent. microcapsules without the healing agent. microcapsules with the healing agent.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.35-42
• /
• 2014

Thermal analysis properties and adhesive properties of self-healing agents were evaluated through differential scanning calorimetry, reaction heat measurement, and adhesive shear test. D1E0, D3E1, D1E1, D1E3, and D0E1, depending on the mixing ratio of DCPD and ENB, were considered as self-healing agents. The amount of Grubbs' catalyst, depending on the type of self-healing agents, was varied from 0.1 wt% to 1.5 wt%. In the case of DCPD, the polymerization reaction occurred faster and the stabilized adhesive strength increased as the amount of catalyst increased; however, a large amount of catalyst was required. ENB had excellent reactivity with a small amount of the catalyst; however, high reaction heat was observed at the early stage of polymerization. Thermal analysis properties and adhesive properties of self-healing agents can be controlled by varying a mixing ratio of DCPD and ENB. Among the self-healing agents used for this study, the D3E1 would be one of the most preferable candidates with regard to maximum adhesive strength, reaching time to maximum adhesive strength, stabilized adhesive strength, and reaction heat.