• Journal of the Korean Society of Visualization
• /
• v.19 no.3
• /
• pp.136-142
• /
• 2021

Submerged and semi-submerged vehicles expel cooling water through an outlet. In this process, induced noise and vibration by the flow around the outlet have been reported, and it may cause problems directly related to survivability of the navy vessels. The coolant outlet has a net-type structure and circular columns are mostly used. In this study, flow measurements using PIV and LDV were performed for different type outlets; conventional (flat plate with round bar) and improved (flat and flat plate) configurations. Experiments were conducted at a cavitation tunnel where pressure and steady flow rate conditions are ensured for sufficient time to measure the flow. The average velocity field of the outlets were measured and compared through LDV measurements, and instantaneous vorticities were evaluated through PIV measurements. The results show that the improved type of the outlet is advantageous in terms of flow stability compared to the conventional type of the outlet.

• Journal of the Korean Society of Visualization
• /
• v.20 no.1
• /
• pp.29-37
• /
• 2022

We carried out a laboratory experiment about the thermo-fluidic characteristics of natural convection boundary layer over a vertical heated plate under constant heat flux condition. Particle image velocimetry has been applied to observe the surface convection velocity close to the vertical plate submerged in the water chamber with the condition of Ra = 7 × 10⁹ and Pr = 8.1. The velocity distributions indicate that the distinct stripe-like structures appears in the upstream (earlier transition region) and the distinct negative-positive and Λ(λ)-shaped flow structures in the downstream (mid-transition region). In addition, the temporal variation of spanwise and streamwise velocity is also presented.

• Journal of the Korean Society of Visualization
• /
• v.19 no.1
• /
• pp.36-42
• /
• 2021

This study measured the velocity of magnetic particles inside the power generation using external heat sources. Single Plane Illumination Microscopy (SPIM) was used to measure magnetic particles that are simultaneously affected by bubbly flow and magnetic field. It has the advantage of reducing errors due to particle superposition by illuminating the thin light sheet. The hydraulic diameter of the power generation is 3mm. Its surface is covered with a coil with a diameter of 0.3 mm. The average diameter of a magnetic particle is 200nm. The excitation and emission wavelengths are 530 and 650nm, respectively. In order to find out the flow characteristics, a total of four velocity fields were calculated in wide and narrow gap air bubbles, between the wall and the air bubble and just below the air bubble. Magnetic particles showed up to 8.59% velocity reduction in the wide gap between air bubbles due to external magnetic field.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.986-990
• /
• 2005

The present study aims to illuminate the vertical velocity profile of outer region of open-channel flow. Two sets of experiments were performed with PIV and propeller velocimeter. The first set was conducted to investigate the effect of bed roughness on the velocity distribution. The second set of experiments was carried out to find the effect of the Froude number on the velocity profile under the same bed roughness. The results reveal that the wake-law fits well with the experimental data from the bottom to the depth of maximum velocity, but it deviates from the experimental data above the maximum velocity point due to velocity-dip phenomenon, and that the velocity profile of the outer region is more influenced by the Froude number than the roughness. It is also shown that both the velocity difference between maximum velocity and surface velocity and the ratio of the average velocity to surface velocity become larger as the Froude number increases.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.961-967
• /
• 2004

An inclined jet impinging on a pin fin heat sink is proposed and investigated experimentally. To investigate the flow pattern, flow visualization using fluorescence and velocity measurement using particle image velocimetry(PIV) are conducted with water. The jet impinges over a wide span of the heat sink with a large recirculation in the upper free space and occasionally with another smaller one in the upstream corner. Further, thermal experimentation is conducted using air to obtain temperature profiles using a thermocouple rake in the air and using thermal image on the heat sink back plate, with impinging angles of 35, 45 and 55 degrees. The Reynolds number range based on the nozzle slot is varied from 1507 to 6405. The results show that impinging angle of 55 degree shows the largest heat transfer capability. The results of thermal experiment are compared and discussed with those of flow visualization.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.518-528
• /
• 2008

The effects of surface roughness on a turbulent boundary layer (TBL) were investigated using particle image velocimetry (PIV). The roughness elements used were periodically arranged two-dimensional spanwise rods, and the roughness height was ${\kappa}/{\delta}$. Introduction of the roughness elements increased the wake strength and the turbulent stress not only in the roughness sublayer but also in the outer layer. This indicates the existence of interaction between inner and outer layers for 2D rod-roughened wall. Roughness effects on a turbulence structure near the wall were obtained by PIV measurements. Iso-contours of mean velocities and Reynolds stresses in the roughness sublayer showed a very good agreement with previous DNS results.

• 한국가시화정보학회:학술대회논문집
• /
• 2003.11a
• /
• pp.75-78
• /
• 2003

An interfacial instability has recently been observed for the DC- and AC-powered electroosmotic flows of the two miscible electrolyte layers having different concentrations in microchannels. It is rather contrary to our common belief that the flow inside a microchannel is generally stable due to the dominant role of the viscous damping. In this work, we visualized the electroosmotic flow inside a T-channel to validate the numerical predictions. It is clearly shown that the strong vortices (which characterize the interface shapes) are generated at the interface of the two fluids, as was predicted in the numerical analysis.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.4
• /
• pp.453-460
• /
• 2005

Experiments were conducted to investigate the effect of the surface roughness on the flat plate turbulent boundary layer. The square rods were installed at the leading edge to make surface roughness. The particle image velocimetry was used to measure the mean velocities and velocity fluctuation component. All measurements were made over a range of w/k=1. 2 5 and $Re_x=80.000{\sim}360,000$. Friction velocity was measured by using Clauser plot method. The level of turbulent intensities on roughness surface appears more strongly than that of turbulent intensities on flat plate. A correlation of boundary layer thickness in term of $Re_x$ and w/k are presented.

• Journal of the Korean Society of Visualization
• /
• v.17 no.2
• /
• pp.39-47
• /
• 2019

Impingement cooling utilizing synthetic jets is emerging as a popular cooling technique because of its high local cooling efficiency. The interaction between the vortex structure of the synthetic jet and the surface is crucial in understanding the mechanism of this technique. In this study, the impinging vortex structure and its advection are investigated by experiments with jet-to-surface spacing $2{\leq}H/D{\leq}7$, and synthetic jet Reynolds number $5120{\leq}Re{\leq}9050$. Using phase-locked particle image velocimetry, ensemble averaged (phase averaged) flow fields are obtained, and vortex identification and quantification techniques are applied. The shape, trajectory, and intensity change of the vortex are assessed. A sharp decline in the vortex intensity and the occurrence of a counter-rotating vortex at the impingement point are observed.

• Journal of the Korean Society of Visualization
• /
• v.19 no.2
• /
• pp.32-40
• /
• 2021

Vapor-driven solutal Marangoni flow is governed by the concentration distribution of solutes on a liquid-gas interface. Typically, the flow structure is investigated by particle image velocimetry (PIV). However, to develop a theoretical model or to explain the working mechanism, the concentration distribution of solutes at the interface should be known. However, it is difficult to achieve the concentration profile theoretically and experimentally. In this paper, to find the concentration distribution of solutes around 2D droplet, the reverse tracking method with an artificial neural network based on PIV data was performed. Using the method, the concentration distribution of solutes around a 2D droplet was estimated for actual flow data from PIV experiment.