• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.285-291
• /
• 2015

A centrifuge works on the principle that particles with different densities will separate at a rate proportional to the centrifugal force during high-speed rotation. Dense particles are quickly precipitated, and particles with relatively smaller densities are precipitated more slowly. A decanter-type centrifuge is used to remove, concentrate, and dehydrate sludge in a water treatment process. This is a core technology for measuring the sludge conveyance efficiency improvement. In this study, a smoothed particle hydro-dynamic analysis was performed for a decanter centrifuge used to convey sludge to evaluate the efficiency improvement. This analysis was applied to both the original centrifugal model and the design change model, which was a ball-plate rail model, to evaluate the sludge transfer efficiency.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.7
• /
• pp.549-555
• /
• 2015

A measurement technique of interfacial velocity in air-water separated flow by particle tracking velocimetry using an infrared camera (IR-PTV) was developed. As infrared light with wavelength in the range of 3-5 um could hardly penetrate water, IR-PTV can selectively visualize only the tracer particles existing in depths less than 20 um underneath the air-water interface. To validate the measurement accuracy of the IR-PTV technique, a measurement of the interfacial velocity of the air-water separated flow using Styrofoam particles floating in water was conducted. The interfacial velocity values obtained with the two different measurement techniques showed good agreement with errors less than 5%. It was found from the experimental results obtained using the developed technique that with increasing air velocity, the interfacial velocity proportionally increases, likely because of the increased interfacial stress.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.3
• /
• pp.87-94
• /
• 2013

As sediment contamination problems have recently been raised in Korea, the need for technologies to remove contaminants in sediments has increased. Contaminated sediments in Korea has been annually dredged and treated using processes of coagulation/flocculation, sedimentation on barges, dewatered and dried at prepared site, and then disposed at a landfill site, which is very costly, and only a limited landfill space available in Korea. Contaminants in media containing a high percentage of silt and clay sized particles, typically, are strongly adsorbed on the particles and difficult to remove. Particle separation processes that separate the fine clay and silt particles from the coarser sand and gravel and concentrate the contaminants into a smaller volume of sediment that can be further treated of disposed of, are very effective in the post step processes. In this study are to test the feasibility of treating dredged sediments using a hydrocyclone process, and to estimate design parameters for a pilot scale test. A hydrocyclone was operated to separate larger particles from the sediments. It was found that the particle separation was greatly affected by the solid contents and inlet pressure in the hydrocyclone.

• Proceedings of the KAIS Fall Conference
• /
• 2009.05a
• /
• pp.885-887
• /
• 2009

고속도로 교량이나 성토지역 노면이 제공하는 자연적인 위치에너지(동력)를 활용하여 수리학적인 입자상 오염물질 분리장치를 실험실 조건에서 운전한 결과 운전압력 0.5기압(수두 5.6m) 이상에서 90% 이상의 제거효율을 보였다. $D_{50}$는 약$45{\mu}m$이었는데 입자의 크기가 $45{\mu}m$ 보다 굵은 입자는 거의 대부분 제거되지만 $45{\mu}m$보다 작은 입자의 제거는 쉽지 않음을 시사해주고 있다. 이러한 입자를 제거하기 위한 후속장치가 필요하며 장치의 원활한 운전을 위해서 유지관리문제에 대한 치밀한 검토가 필요하다.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.12
• /
• pp.937-942
• /
• 2013

Fluid generated within the sonic or ultrasonic waves are reflected by the wall, while the opposite direction forming a predetermined sound wave to the acoustic standing wave is referred to. In this study, the frequency of 1.0 MHz and 2.0 MHz acoustic standing wave generation module is installed in a continuous particle separation device, the laminar flow of influent, taking into account the hydraulic retention time (HRT) in accordance with changes in particle separation characteristics investigated. Operation of a standing wave in the particle separation device about $1.3{\sim}2.8^{\circ}C$ temperature is increased, but did not significantly affect the formation of standing waves. During operation, the HRT 1 hr frequency 1.0 MHz 2 hr, 4 hr longer as the particle separation efficiency (turbidity) were 64.1%, 70.0%, 74.3% and, 2.0 MHz has 58.0%, respectively, depending on HRT, 61.8%, 70.7% in the respectively. That is, the same frequency, the HRT treatment efficiency is 10% or more, depending on differences in generation and, 1.0 MHz frequency, 2 hr, 2.0 MHz 4 hr at about 70% or more of the processing efficiency can be maintained. Frequency of 1.0 MHz and 2.0 MHz operation at the same time, as a result, HRT 1 hr, 2 hr, 4 hr particle separation efficiency of 63.8%, respectively, 70.6%, 77.6%, rather than the generation of standing waves appear continuous HRT is affecting a lot of particles to separate could know.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.83-92
• /
• 1999

A numerical analysis of two phase flow in the solid rocket nozzle was conducted. Stoke number was defined over the various aluminum oxide($AI_2$$O_3$) particle sizes and particle trajectories were treated by Lagrangian approach. Particle stability was considered by the definition of Weber number in a rocket nozzle. Large particles are divided after the nozzle throat as the flow accelerates rapidly. The division of particles changes the particle distribution at the nozzle exit. From the above results, it was found that the nozzle converge section surface might be affected by aluminum oxide particles. Also, Mechanical erosion rate of nozzle surface was predicted for different materials.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.775-782
• /
• 2002

The effects of solid and dispersant concentration was investigated by wet-sieving method for knowing the amount of coarse particle in fine powders. In the work alumina powders, sodium hexametaphosphate and sodium polyacrylate were used for preparing slurry. It was confirmed that the coarse particle mass increased by increasing alumina concentration and decreasing dispersant concentration. With systematic measurements we know that the alumina powder and dispersant of one weight percent(1.0wt%) were proper quantity for coarse particle mass measuring, respectively. Sodium polyacrylate as dispersant showed higher coarse particle mass than sodium hexametaphosphate. The sieve mass was decreased according to increase of experiment number. Based on experiments it was considered that wet-sieving method is good tool for measuring a coarse particle mass in fine powders.

• Resources Recycling
• /
• v.29 no.3
• /
• pp.36-42
• /
• 2020

In the present study, gravity separation of speiss (6.74 g/㎤) and limestone (2.7 g/㎤) was investigated using a vibrating 1 mm-zirconia ball (5.6 g/㎤) bed as a medium. The floating ratio and separation efficiency with increasing the number of spiess and limestone granules were examined by changing the vibration frequency from 18 Hz to 26 Hz. During the vibration, the zirconia balls circulate inside the vessel, and the spiess granules sink with the zirconia balls, but limestone granules remain on the surface of the zirconia ball bed. As the number of particles of spiess and limestone granules increased, it was observed that the granules were congested in the path of the granule sinking, so the rate of particle sinking decreased, and that limestone granules overlapping with the spiess granule also sunk. Therefore, the separation efficiency decreases with increasing the number of granules, but when the vibrational frequency increases, there is no more congestion and the separation efficiency increases. When each of the three particles was added, a separation efficiency of 100% was acheived at 22 Hz, which indicates that a dry gravity separation process that does not require a drying process is possible.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.21-21
• /
• 2010

현재 시대에는 자원의 부족으로 인하여 원재료의 낮은 등급을 정제하는 것이 중요하다. 자기분리 기술이 산업 계 원재료들의 정제에 적용되는 것이 기대된다. 예를 들면 고순도의 유리나 절연체를 제작하기 위한 원재료에서 철산화물의 제거는 매우 중요하다. 자기를 띠는 입자들과 자기분리 필터 와이어 사이에 발생하는 끌어당기는 힘은 다른 자기분리와 비교 할 때 초전도 자기분리에서 훨씬 강하다. 초전도 마그네트를 이용하여 높은 자기장을 형성하기 때문에 일반 자기분리의 자성 입자 포획력을 능가한다. 본 연구에서는 습식 조건에서 산업계 원재료로부터 철계 산화물을 제거하기 위해서 초전도 자기문리를 사용하여 실험하였다. 실험에 사용된 시료는 유리원료로 사용되는 2종류로 시료A는 0.1 ~ 0.3 mm의 평균입도를 갖는 모래형상이며 시료B는 평균입도 0.03 ~ 0.1 mm의 고운모래 형태이다. 자기분리를 위해 상온에서 100 mm의 직경을 갖는 600 mm의 높이의 전도냉각형 Nb-Ti 초전도 마그네트를 사용하였으며 시료를 위에서 공급하고 아래로 배출되도록 수직형으로 설치하였다. 시료 500 g과 증류수 2 L를 혼합하여 교반시키고 6 T의 자기장 하에서 실험하였다. 자기분리 필터는 초전도 마그네트에서의 자기장의 분포를 해석하여 디자인하였다. 자기분리 필터의 자기적 특성을 알아보기 위해 진동시료형 자력계를 사용하였다. 산업계 원재료는 X선 형광분석기를 사용하여 성분을 분석하였다. 산업계 원재료를 이용하여 초전도 자기분리를 실시한 결과 철계 산화물은 시료A에서 43.5 %제거되었으며 시료B에서는 77.3%제거되었다.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.05a
• /
• pp.228-230
• /
• 2005

본 연구에서는 생활 폐기물의 소각 바닥재를 사용하여 입도 분리한 후 각 입도별 철 비철 금속이 함유된 바닥재를 자력세기에 따라 분리하였다. 철의 분석결과 4mesh이상의 입자에서 대부분의 철이 회수되었고 4mesh이하에서는 철의 함유량이 적었지만 50mesh 이하의 입자에서는 자력에 의해 대부분 분리되었다. 또한 각 입도에 따른 자력세기별로 철의 회수율을 측정한 결과 $25{\sim}130gauss(30{\sim}150volt)$에서는 낮은 회수율을 보였고 380gauss(150volt이상)의 높은 자력에서만 분리가 일어남을 확인할 수 있었다. 비철은 대부분 4mesh에서 분포하였고 전체적으로 낮은 양이 존재하였다.