• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.22 no.2
• /
• pp.121-127
• /
• 1977

Leaf burning due to nitrofenapplication was characterized as brown color spot appearing on the leaf sheath and blade. The spots predominantly appeared around 5-7 cm high above soil surface regardless of different particle size, formulation, application method, or water level. Magnitude and frequency of burn spots increased somewhat as the granular size gets finer, by higher water level, or in transplanted rice compared to directly sown rice when applied at 7 leaf-stage, but there was no indication of increase in leaf burning due to clinging of floating dust to rice plant. When collections from local distributor's stock of TOK 7G, a granular formulation of nitrofen, were analyzed for particle size composition, 98.9% by weight ranged between 9 to 35 meshes, and only about 0.08% by weight was of particles finer than 100 mesh.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.3
• /
• pp.284-290
• /
• 2012

Cement Fineness Modulus (CFM) is a method of expressing the distribution of particle sizes of cement in numeric form. If CFM is controlled through crush process of cement without modifying the chemical components or mineral composition of cement, it is judged to be able to produce a cement satisfying various requirements because it is estimated to enable various approaches to cement such as high early strength, moderate heat, low heat cement and so on. Therefore, in this study, as basic research for manufacturing special cement utilizing the controls of CFM, the intention was to review the impacts of CFM on the fundamental properties of concrete. To summarize the result, as mixture characteristics of fresh concrete, ratio of small aggregate and unit quantity were gradually increased, securing greater fluidity, with an increase in CFM, while the amount of AE and SP were reduced gradually. In addition, setting time was delayed as CFM increased. Furthermore, compression strength was relatively high during initial aging as CFM became smaller, but as time passed, compression strength became smaller, and it showed the same level of strength as aging time passed about three years.

• Journal of the Korean Society for Railway
• /
• v.18 no.4
• /
• pp.354-362
• /
• 2015

Since allowable settlement of concrete slab track is about 30mm, a lot of attention must be paid to the settlement of the earthwork (reinforced trackbed, upper subgrade, under subgrade) under the concrete track. To this end, more experimental data should be accumulated through tests for these materials. In this study, we evaluate the long-term settlement of reinforced trackbed and subgrade materials using factors such as repeated loading conditions, water content, and grain size distributions in a large triaxial test and a large oedometer test. In cases in which the performance of the reinforced trackbed layer meets the design criteria, the settlement caused by train load was considerably small. But, when the water content increases in the subgrade, unexpectedly large settlement might occur for certain grain size distributions of the subgrade materials.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.745-749
• /
• 2012

국내 주요하천은 지속적인 산업화와 난개발로 인해 생태계파괴 및 수변생물의 서식처 환경 악화로 하천 생태계에 많은 악영향을 받고 있다. 그러나 1990년대 이후 국내에서는 하천의 기능과 생물의 다양성, 하천환경 및 생태학적인 가치와 중요성에 대한 인식이 매우 커짐에 따라 하천의 생태적 기능을 매우 중요시 하고 있으며, 하천의 난개발로 인한 피해를 복원하기 위해 활발한 연구가 진행되고 있다. 대표적인 연구로 생태계 건전화 개념을 도입하여 담수성 어류 서식처 제공 및 이동에 필요한 유량을 산정한 한국 수자원공사(1995)의 연구가 있으며, 김규호 등(1996a, 1996b)은 물고기 서식처 환경 중 특히 수심과 유속 등 수리조건을 유지하기 위한 최소유량 산정 방법을 제시하였다. 또한 노경범(2011)은 섬진강의 하천환경 회복을 위한 연구대상 구간에서의 대표어종을 선정하여 서식처 특성 파악을 위해 하천 특성을 연구하였다. 이와 같이 현재 국내에서도 하천의 기능과 생태학적 기능을 위한 노력과 연구가 진행되고 있다. 그러나 생태학적 서식처 연구에서는 아직까진 미진한 부분이 많이 있다. 그 예로 보호종이나 멸종위기어종과 같은 생물의 서식처 확보를 위한 연구가 아직까지는 많은 노력과 연구가 필요한 상태이다. 본 연구에서는 환경부에서 지정한 멸종위기 1급 어종인 퉁사리를 대상으로 서식환경 특성 연구를 진행하였으며, 퉁사리의 생태학적 서식특성과 현재 지석천 상류 유역에서 관찰되고 있는 서식구간을 중심으로 MD-SWMS (Multi-Dimensional, Surface Water Modeling System) 모형을 이용하여 수리특성 분석을 수행하였다. 이를 위해 하상재료 입도분석을 실시하였으며, 그 결과 입도가 큰 굵은모래 및 잔자갈, 굵은자갈로 구성되어 있음을 알 수 있었다. 또한, 수리학적 특성분석결과 서식구간 내에서는 비교적 빠른 유속이 나타났다. 이러한 퉁사리의 서식환경의 특성 분석으로 서식구간 내 입도가 큰 하상재료로 구성되어 있으며, 퇴적구간이 생성되지 않을 정도의 유사이송량과 유속이 필요할 것으로 분석되었다. 향후 퉁사리의 장기적인 서식환경 조성과 보존을 위해 대상구간의 유사이송의 연구와 실측 및 수변환경 모니터링을 통한 다양한 연구가 진행되어야 할 것으로 판단된다.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.1
• /
• pp.51-59
• /
• 2021

In this study, the purpose of this study was to quantitatively grasp the specific correlation between the raw material and the occurrence of leakage by analyzing the characteristics of leakage by adjusting the type and content of the raw material constituting the asphalt mastic coating waterproofing material. To this end, two raw materials, CA (calcium carbonate) and ASE (anti-sedimentation), which are organic and mineral extender for asphalt mastic waterproofing membrane coating, were selected. viscosity and oil leakage stability (20 ℃, 40 ℃) was evaluated. As a result of the evaluation, the oil leakage stability and viscosity were inversely proportional to the CA average particle size, and it was quantitatively proven that a correlation in proportion to the ASE content was established. The results of this study are expected to be used as core data for basic mixing design in the future mixing studies to improve leakage of asphalt mastic waterproofing membrane coating.

• The Korean Journal of Malacology
• /
• v.11 no.1
• /
• pp.21-34
• /
• 1995

1987년 6월부터 1990년 5월까지 진해만의 저서동물 군집에서 우점하는 아기반투명조개(Theora fragilis A. Adams)에 대한 개체군 생태학적 연구를 수행하였다. 조사결과, 이 종의 주된 분포 구역은 진해만의 입구 정점이었으나 겨울철에는 내만의 안쪽으로 확장되었다. 이 종은 여름철과 겨울철의 2회에 걸쳐 치패의 착저가 관찰되었으나 주 착저시기는 여름철이었다. 진해만 입구의 정점에서는 이러한 대량착저로 인해 그 밀도가 2,116개체/m$^{[-992]}$ 에 달하였다. 그러나 착저한 치패의 초기 감모로 인해 가을철의 밀도는 급격히 낮아졌다. 한편, 이 종의 분포는 퇴적물의 유기물 함량과 깊은 관계를 보여서 3.0-5.0%(평균 4.54$\pm$1.42%), 퇴적물의 평균 입도 8.97($\pm$0.62)$\varphi$사이에서 상대적으로 높은 밀도를 보였다. 그러나 퇴적물의유기물 함량의 증가와 함께 이 종의 밀도가 대체로 증가하지만 5.0% 이상에서는 다시 감소하는 현상을 보였다. 이 종은 여름철 저층수의 빈산소 수괴가 사라진 후에는 다시 진해만의 안 쪽 내만정점에서 높은 밀도를 나타냈다. 따라서 진해만에서의 본 종의 분포는 전반적으로 퇴적물의 유기물 함량. 퇴적물의 입도 조성 및 저층수의 용존 산소량 등에 의해 결정된다고 판단된다.

• Applied Chemistry for Engineering
• /
• v.21 no.6
• /
• pp.676-679
• /
• 2010

Nano composite particles were synthesized from a bulk ZrVFe alloy ingot by transferred DC thermal plasma. Effects of plasma gas flow rate on the characteristics of the produced nano composite particles were investigated. The characteristics of the synthesized powder were analyzed by field scanning electron microscopy (FE-SEM), light scattering particle size analyzer (PSA), energy dispersive X-ray spectroscopy (EDS), X-ray diffractometer (XRD), and Brunauer-Emmett-Teller (BET) surface area analyzer. As the flow rate of plasma gas increased from 20 L/min to 40 L/min, the average particle size decreased from 91 nm to 55 nm, the particle size distribution became narrower, the surface area increased from $200\;m^2/g$ to $255\;m^2/g$, the particle composition was nearly unaffected, and the particle crystallinity was improved.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.157-165
• /
• 2000

The applicability and performance of HMS-25 as the railroad roadbed materials were evaluated through the model and laboratory tests. The uniaxial compression test of HMS-25, model soil box test, and combined resonant column and torsional shear test were performed for static and dynamic analysis of railroad roadbed. The uniaxial compression test result of HMS-25 shows steady increase in strength due to hardening chemical reaction between HMS-25 and water. The result of model soil box test reveals that railroad roadbed of HMS-25 is better than that of soil in several aspects such as bearing capacity and settlement. The combined resonant column and torsional that shear test result indicates that shear modulus of HMS-25 increases with the power of 0.5 to the confining pressure and that shear modulus increases with the increase of curing period.

• Journal of the Korean Magnetics Society
• /
• v.11 no.1
• /
• pp.8-13
• /
• 2001

Effects of casting Processes and lubricant addition were studied to improve remanence of 31RE-68TM-lB based sintered magnet by using axial pressing process. Strip casting was effective to get the fine and homogeneous microstructure without ${\alpha}$-Fe segregation. The strip cast flake resulted in narrower particle size distribution after jet milling with respect to the conventional cast ingot. During pressing step with a magnetic field, the particle alignment was increased by appropriate addition of liquid lubricant. In this study, it was revealed that narrow particle size distribution and appropriate addition of liquid lubricant were essential to improve the grain alignment and thus the remanence of Nd-Fe-B sintered magnet.

• Journal of the Korean Magnetics Society
• /
• v.22 no.2
• /
• pp.42-44
• /
• 2012

We have studied a means to control the composition of nickel-iron thin films. By changing current and voltage applied to a electroplating electrolyte we could manipulate the relative concentration of nickel and iron in the thin films, which caused variations of coercivity, squareness, and saturation magnetic field. As we increase the content of iron in the thin films by using potentiostatic and galvanostatic plating, the grain size was increased and the coercivity was reduced.