• Journal of Aerospace System Engineering
• /
• v.14 no.3
• /
• pp.1-9
• /
• 2020

In this paper, the effects of the delta winglet vortex generator, the airfoil vortex generator and the guide vanes on the friction factor and the Colburn factor in the fin-tube flow were studied. The vortex generator and guide vane were non-dimensionalized based on the channel height and tube diameter, and locations were selected according to the authors' suggestions. The Reynolds number based on the inlet velocity and the tube diameter was selected in the range of 1400-8000. As a result, the friction factor resulted in a 4.7% decrease in guide vanes at the Reynolds number 8000 over the conventional fin-tube, and the Colburn factor resulted in a 33% increase in the delta winglet vortex generator at the Reynolds number 3800 over the conventional fin-tube.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.3
• /
• pp.161-169
• /
• 2017

The present study investigated the effect of the rib arrangement and a guide vane for enhancing internal cooling of the blade. Two types of rib arrangements were used in the first and second passage in parallel. Aspect ratio of the channel was 5 and a fixed Reynolds number based on hydraulic diameter was 10,000. The attack angle of rib was $60^{\circ}$, rib pitch-to-height ratio (p/e) was 10, and the rib height-to-hydraulic-diameter ratio ($e/D_h$) was 0.075. The effect of an interaction between Dean vortices and the secondary vortices from the first passage was observed. Overall, the attack angle of rib in the first passage was dominant factor to heat transfer and flow patterns in turning region. Also, the channel with a guide vane showed enhanced heat transfer at the tip surface with reducing flow separation and recirculation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.519-524
• /
• 2019

A horizontal dust collector is used in a large wind-volume grain dryer. In this study, Computational Fluid Dynamics (CFD) was used to analyze the flow characteristics inside the dust collector, including the effects of wear on the conical hub on the dust collection performance. Recently, a horizontal cyclone dust collector was developed with a conical hub and fixed vanes at the inlet of the dust collector to generate swirl flow to separate foreign matter from the air. The dust collector is relatively small in size and easy to install, and it has a relatively low back pressure, which does not require any additional power. However, there are problems with a back pressure problem and dust deposition that are caused by the shape of the horizontal dust collector. To solve these problems, the flow characteristics were studied with internal shapes of the dust collector using three-dimensional flow analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.88-96
• /
• 2008

Effects of the duct inlet guide vane on the flowrate distribution characteristics of the defroster nozzle exit in a defrost duct system were investigated experimentally to design the optimum heating, ventilation and air conditioning (HVAC) system applied in an automotive compartment. A 3-dimensional hot-wire anemometer system was used to measure the velocity field in the vicinity of the defroster nozzle jet flow and the velocity distributions near the windshield interior surface. At first, two cases of with- and without-duct inlet guide vanes were considered as the test condition, and then three cases of the duct inlet guide vane were tested to determine the optimum guide vane shape and their positions. The arrangement of the duct inlet guide vanes has an effect on the improved flowrate distribution at the defroster nozzle exit and near the windshield interior surface. However, the application of the lots of guide vane to control the flow direction leads to increase the flow resistance, resulting in the decreased flowrate issuing from the defroster nozzle. The shape of the duct inlet guide vane affects not only the flowrate distribution between the driver side and the assistant driver side but also the reduction of the flow resistance in the defrost duct system.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05a
• /
• pp.367-370
• /
• 2012

본 연구는 하나의 장치 내에서 "싸이클론-관성충돌-여과포 집진"이라는 다단 제진 단계가 동시에 이루어져 입경 분포별로 순차적인 제진이 가능한 멀티 집진기의 처리가스 제어 효율을 극대화시킬 수 있는 기류 흐름을 얻기 위한 최적화 설계 조건을 검토하는 것이다. 우선 1단계 제진 과정인 원심력을 이용하여 조대입자의 유선 이탈을 촉진시킬 수 있는 사이클론 유동을 최적화시키기 위한 집진기 입구 형상 설계 검토를 위해 수치 해석적 연구를 수행하였다. 그 결과, 멀티집진기 입구 형상을 일반적인 설계 방식인 접선 유입식으로만 설계한 것에 비해 선회류를 한번 더 가속화시킬 수 있는 가이드 베인을 추가로 설계한 경우 선회류의 pitch가 짧고 강하게 형성되어 사이클론부에서 조대입자의 유선 이탈을 촉진시키는데 매우 효과적인 것으로 예측되었다. 단, 사이클론부 하단 벤츄리 형상으로 인해 약 4~5 m/s의 강한 하향 흐름이 호퍼 하단까지 형성되고 있어 탈리 분진의 재비산 문제가 발생할 가능성이 크므로 벤츄리 형상 설치 유무에 대한 영향도 추가적으로 연구가 필요할 것으로 판단된다.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.4
• /
• pp.45-50
• /
• 2010

The goal of paper is to investigate the flow and scalar distribution through the HP Nozzle Guide Vane (NGV) passage. Flow and scalar distribution measurement are conducted by using 5-hole pressure probe and $CO_2$ tracing technique, respectively. Three different experimental cases are considered depending on cooling flow condition. The result shows that the vortical secondary flow patterns are observed clearly and these flow characteristics maintain through the NGV passage regardless of cooling flow injection. Compared to center region, the high axial velocity flow is observed near wall region due to cooling flow injection. Without cooling flow, the $CO_2$ (scalar) distribution becomes to be uniform quickly due to the strong flow mixing phenomenon. However, in cases of cooling flow, scalar distribution is significantly non-uniform.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.1 s.6
• /
• pp.43-50
• /
• 2000

Upgrade development of a high pressure ratio centrifugal compressor in marine engine turbochargers is presented. A new matched operating point at increased speed of rotation was determined through system cycle analysis using the exisitng test data of turbine performance. Under some severe restrictions for geometric parameters, the state-of-the-art methods of both aerodynamic design and CFD analysis were applied, in which only an impeller, a vaned diffusor and some part of casing wall were modified. Prototype hardware was fabricated and assembled for system performance tests. Excellent performance in pressure ratio and efficiency was obtained over whole speed region. Reduced surge and choke margin was, however, observed at design speed of rotation.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.3
• /
• pp.314-321
• /
• 2020

In this work, a preliminary design of an inlet guide vane and runner for developing a 2.5 kW hydraulic turbine was conducted by using computational fluid dynamic analysis. Three-dimensional Reynolds-averaged Navier-Stokes equations with shear stress transport turbulence model were used to analyze the fluid flow in the hydraulic turbine. The hexahedral grid system was used to construct computational domain, and the grid dependency test was performed to obtain the optimal grid system. Velocity triangle diagram considering the flow angles of the inlet guide vane and runner was analyzed to obtain a basic geometry of the inlet guide vane and runner. Through modification of the preliminary design, the hydraulic performances of the turbine have improved under overall drop conditions. Especially, the efficiency and power of the turbine increased by 0.95% and 1.45%, respectively, compared to those of the reference model.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.418-423
• /
• 2014

Small hydropower has been considered as a solution to resolve the problem of exhaustion of fossil fuel and industrial pollution. In this study, we developed and tested a Cross-Flow Turbine with two guide vanes to optimize the small hydropower for the site condition with large fluctuation of head and flow rate. Furthermore, in the condition of constant inlet head, CFD analysis was carried out to analyze the effect of air suction and valve position on the performance characteristics. The results showed that the air suction can minimize the hydraulic loss caused by the Recirculation flow in the runner passage and flow impact on main shaft so that it can increase the turbine efficiency and output power.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.983-989
• /
• 2013

The current research reviewed the design conditions that would maximize the efficiency of the hybrid collector that combines in one unit "cyclone-inertial impaction-bag filter". The computational analysis for the shape of cyclone entry predicts that a design that installs the guide vane at the entry of the tangential type cyclone brings a high-rpm and powerful vortex, very effective in promoting the deflection of coarse particles from the streamline at the cyclone. As the lower part of the cyclone is venturi-shaped, however, a strong flow downward of 4 to 5 m/sec persists through the lower part of the hopper, revealing the likely reentrainment of collected dust. And the removal of the venturi at the lower part of the cyclone would solve the problem of the reentrainment of collected dust. The acceleration of the flow velocity through the adjustment of the gap of the collision baffle would increase the effect of collision, but as the interference with the dust separation is expected, the original design should be kept for the baffle.