• Korean Chemical Engineering Research
• /
• v.44 no.6
• /
• pp.650-658
• /
• 2006

The recycling of TDA from solid waste of TDI plant(TDI-R) by near-critical hydrolysis reaction had been studied by means of a statistical design of experiment. The main and interaction effects of process variables had been defined from the experiments in a batch reactor and the correlation equation with process variables for TDA yield had been obtained from the experiments in a continuous pilot plant. It was confirmed that the effects of reaction temperature, catalyst type and concentration, and the weight ratio of water to TDI-R(WR) on TDA yield were significant. TDA yield decreased with increases in reaction temperature and catalyst concentration, and increased with an increase in WR. As a catalyst, NaOH was more effective than $Na_2CO_3$ for TDA yield. The interaction effects between catalyst concentration and temperature, WR and temperature, catalyst type and reaction time on TDA yield had been defined as significant. Although the effect of catalyst concentration on TDA yield at $300^{\circ}C$ as subcritical water was insignificant, the TDA yield decreased with increasing catalyst concentration at $400^{\circ}C$ as supercritical water. On the other hand, the yield increased with an increase in WR at $300^{\circ}C$ but showed negligible effect with WR at $400^{\circ}C$. The optimization of process variables for TDA yield has been explored with a pilot plant for scale-up. The catalyst concentration and WR were selected as process variables with respect to economic feasibility and efficiency. The effects of process variables on TDA yield had been explored by means of central composite design. The TDA yield increased with an increase in catalyst concentration. It showed maximum value at below 2.5 of WR and then decreased with an increase in WR. However, the ratio at which the TDA yield showed a maximum value increased with increasing catalyst concentration. The correlation equation of a quadratic model with catalyst concentration and WR had been obtained by the regression analysis of experimental results in a pilot plant.

• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.624-631
• /
• 1993

The composites in the system aluminium titanate-mullite were synthesized by stepwise alkoxide hydrolysis of tetraethylorthosilicate, Si(OCLH5), and titaniumtetraethoxide, $Ti(OC_{2}H_{5})_4$ in $Al_{2}O_{3}$ ethanolic colloidal solution. All particles produced by sol-gel-process were amorphous, monodispesed and had a narrow particle size distribution. Sintered bodies at $1600 ^{\circ}C$ for 2h were subjected to prolonged durability tests-on the one hand annealing at the critical decomposition temperature of $1100 ^{\circ}C$ for lOOh and on the other cyclic thermal shock between 750 and $1400 ^{\circ}C$ for 100h. The best thermal durability was achieved by a composition containing 70 and 80 vol% aluminium titanate, which showed little change in microstructure and thermal expansion cycles during the tests. The microstructural degradation of samples studied using scanning electron microscopy, X-ray diffraction, and dilatometry, was presented here. The study was conducted in order to predict the service life of aluminium titanate-mullite ceramics formed by this processing route.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.89-94
• /
• 2015

This study was conducted to compare the laser weldability of boron steel and hot-stamped steel. In general, boron steel is used in the hot-stamping process. Hot-stamping is a method for simultaneously forming and cooling boron steel in a press die after heating it to the austenitizing temperature. Hot-stamped steel has a strength of 1500 MPa or more. Thus, in this study, the laser weldability of boron steel and thet of hot-stamped steel were investigated and compared. A continuous wave disk laser was used to produce butt and lap joints. In the butt welding, the critical cooling speed at which full penetration was obtained in the hot-stamped steel was lower than that of boron steel. In the lap welding, the joint widths were similar regardless of the welding speed when full penetration was obtained.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.12
• /
• pp.1147-1152
• /
• 2013

In this study, the effect of an insulation coating on the start time of a linear region is theoretically investigated when an insulation-coated hot-wire is used for the transient hot-wire method (THWM). For this purpose, important parameters affecting the start time of the linear region are presented from an analytical solution of temperature-rise for an insulation-coated hot-wire. Furthermore, a critical time to ignore the influence of important parameters is studied. The theoretical results indicate that the effect of the insulation coating rapidly disappears with a decrease in the wire radius, coating thickness, thermal diffusivity of insulation material or an increase in the thermal conductivity of the insulation material. The results of this study will be helpful for selecting a proper start time of the linear region for the THWM using insulation-coated hot-wires.

• Journal of the Korean Vacuum Society
• /
• v.18 no.3
• /
• pp.208-212
• /
• 2009

The optical characterization of self-assembled InAs/AlAs quantum dots(QD) grown by MBE were investigated using photoreflectance spectroscopy. The intensities of the signals of the GaAs buffer and wetting layer(WL) changed with the width of the WL layer. The PR spectrum for the sample, in which QDs layer were etched off at room temperature, indicated that the broadened signal ranging $1.1{\sim}1.4\;eV$ was originated from InAs QDs and WL. The intensities of signals of GaAs buffer and the WL changed with the WL width. A red shift of the PR peak of WL are observed when the annealing temperatures range from $450^{\circ}C$ to $750^{\circ}C$, which indicates that the interdiffusion between dots and capping layer is caused by improvement in size uniformity of QDs.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.62-67
• /
• 2007

The effects of the heat-treatment temperature on the carbon (C) substitution amount, full width at half maximum (FWHM) value, critical temperature ($T_c$), critical current density ($J_c$) have been investigated for 10 wt % malic acid ($C_4H_6O_5$)-doped $MgB_2/Fe$ wires. All the samples were fabricated by the in-situ powder-in-tube (PIT) method and heat-treated within a temperature range of $650^{\circ}C$ to $1000^{\circ}C$. As the heat-treatment temperature increased, it seemed that the lattice distortion was increased by a more active C substitution into the boron sites from the malic acid addition. These increased electron scattering defects seemed to enhance the $J_c-H$ properties in spite of an improvement in the crystallinity, such as a decrease of the FWHM value and an increase of the $T_c$. Compared to the un-doped wire heat-treated at $650^{\circ}C$ for 30 min, the $J_c$ was enhanced by the C doping in a high-field regime. The wire heat-treated at $900^{\circ}C$ resulted in a higher magnetic $J_c$ of approximately $10^4\;A/cm^2$ at 5 K and 8 T.

• Analytical Science and Technology
• /
• v.11 no.4
• /
• pp.260-265
• /
• 1998

Spherical, ${\mu}m$-sized particles of barium titanyl oxalate were prepared by thermal decomposition of dimethyl oxalate in acidic barium and titanium solutions. Precipitation was carried out in the presence of several supporting anions. Spherical particles having a specific type of particle size distribution. i.e., unimodal or bimodal distribution, with mean size in the range of $0.2{\sim}3{\mu}m$, were formed depending on the supporting anions, oxalate ion generation rate and aging time. Particles of barium titanyl oxalate settled on the bottom of the beaker at the aging time of 120 min grew to the critical monosize of about $1.5{\sim}3{\mu}m$. XRD spectra and chemical analyses of barium titanate showed that barium titanyl oxalate with high qualities could be synthesized by choosing chloride ion as a supporting anion and increasing the reaction temperatures.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2009.11a
• /
• pp.346-346
• /
• 2009

산화물 형태 사용후핵연료의 효율적 처분 혹은 재활용을 위한 연구 가운데, 고온의 LiCl 용융염 중에서 전해환원하여 금속으로 환원시킨 후, 환원된 금속을 고온의 LiCl-KCl 용융염에서 전해정련하는 연구가 국내외적으로 활발하게 진행되고 있다. 전해환원을 위해 일정 농도 $Li_2O$가 LiCl 용융염에 첨가되며 $Li_2O$ 농도가 높으면 반응 재질의 부식성이 크게 증가하므로 일반적으로 우라늄 산화물은 1wt% 이하의 $Li_2O$ 농도에서 전해환원 된다. 우라늄 산화물의 전해환원 전위는 $Li_2O$의 전해환원 전위 보다 표준 상태를 기준으로 공정온도인 650 $^{\circ}C$ 에서 약 70 mV 정도 낮기 때문에 전해환원 과정에서 $Li_2O$ 의 환원으로 Li 금속이 생성될 가능성이 있으며 우라늄 산화물은 대부분 직접 전해환원 되지만 일부 Li에 의해 화학적으로 환원되기도 한다. 전해환원 공정에서 환원되지 않은 희토류 산화물은 전해정련 공정에서 $UCl_3$와 반응하여 $UO_2$를 생성시켜 공정 효율을 떨어뜨린다. 따라서 전해환원 공정에서 가능하연 최대한 희토류 산화물을 금속으로 환원시키는 조건을 찾아내는 것이 바람직하고 이를 위해서 우선 전해환원 공정에서 희토류 산화물의 화학적 거동의 이해가 요구된다. 본 연구에서 열역학적 검토를 통하여 희토류 산화물의 환원 조건을 조사한 결과 희토류 산화물은 매운 낮은 $Li_2O$ 농도에서 Li에 의해 환원되고, 1wt% 이하의 $Li_2O$ 농도에서는 Sc와 Lu의 산화물이 $Li_2O$와 복합산화물을 형성하고 이들 복합산화물은 Li에 의해 환원되지 않는 것으로 나타났다. 또한 희토류 원소 별로 희토류 원소 산화물의 Li에 의한 환원 조건으로서 평형상태에서의 $Li_2O$ 농도 즉 환원 임계 $Li_2O$ 농도를 실험적으로 측정하였으며 1wt% $Li_2O$ 농도 이하에서 열역학적 해석과 동일하게 Sc와 Lu만이 복합산화물을 형성하여 Li에 의해 직접환원 되지 않는 것으로 관찰되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.12
• /
• pp.6013-6021
• /
• 2012

Although there are many patients who suffer from cold hypersensitivity and have a difficult time in living daily lives due to feeling cold at room temperature, it is about true that an accurate diagnostic method and an effective remedy for a cold hypersensitivity have not been developed yet. Therefore, in order to develop traditional medicine equipment for cold hypersensitivity, we have designed new oxygen chamber system which can diagnose cold hypersensitivity with multiple bionic sensors and supply a patient optimum amount of oxygen adaptively to the extent of their illness. In particular, diverging from conventional diagnosis based on the experience of doctor and subjective statements of patient, we introduced accurate method for diagnosis in comparing between output of multiple sensors and threshold derived from clinical trials. After all, the proposed oxygen chamber system will contribute to achieving scientific evidence and manufacturing of korean traditional medicine.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.11-11
• /
• 2006

ZnO는 넓은 밴드갭(3.37eV)과 큰 액시톤(exciton) 결합에너지(60meV)를 가지는 II-VI족 화합물 반도체이다[1]. 이와같은 특성은 상온에서도 높은 재결합 효율이 기대되는 엑시톤 전이가 가능하여 자발적인 발광특성 및 레이저 발진을 위한 낮은 임계전압을 가져 일광효율이 큰 장점이 있다. 최근에는 ZnO의 전기적, 광학적, 자기적 특성을 높이기 위해 doping에 대한 연구가 많이 보고 되고 있다. 이중 ZnO내에 Mg을 doping하게 되면 Mg 조성에 따라 밴드갭이 3.3~7.7eV까지 변하게 된다. 그러나 이원계 상평형도에 따라 ZnO내에 고용될 수 있는 MgO의 고용도는 4at% 이하이다. 이는 ZnO는 Wurtzite 구조이고, MgO는 rocksalt 구조로 각각 결정구조가 다르기 때문이다. 본 연구는 열기상증착방법(thermal evaporation)으로 ZnO 템플레이트를 이용하여 MgZnO 나노막대를 합성하였고, Zn와 Mg의 서로 다른 녹는점을 이용해 2-step으로 성장을 하였다. 합성은 수평로를 사용하였으며, 반응온도 550, $700^{\circ}C$로 2-step으로 하였으며, 소스로 사용된 Zn(99.99%)과 Mg(99.99%) 분말을 산소를 직접 반응시켜 합성하였다. Ar 가스와 O2 가스를 각각 운반가스와 반응가스로 사용하였다. ZnO 템플레이트 위에 성장시킨 1차원 MgZnO 나노구조의 형태 및 구조적 특성을 FESEM과 TEM으로 분석하였다. 그리고 결정학적 특성은 XRD를 이용해 분석하였다.