• Journal of the Korean Geotechnical Society
• /
• v.37 no.12
• /
• pp.47-56
• /
• 2021

The cryosuction (negative pore pressure) in freezing soils causes groundwater migration from the frozen fringe to freezing front for ice lens formation. Frost heave and heaving pressure by ice lens cause damage to ground infrastructure. In order to prevent damage by the frost heave, various frost susceptibility criteria have been proposed. The SP (Segregation Potential) is the most widely used classification criterion for frost susceptibility in cold regions. The expansion of the ice lens by the migration of the groundwater is a key role in frost heave mechanism, and thus it is necessary to evaluate the hydraulic conductivity. In this paper, soil mixtures of coarse-fines (sand-silt) were prepared in various weight fractions and used for frost heave and column permeability test. For each case, the SP and the hydraulic conductivity were derived and correlations were analyzed. As a results, the transition threshold of the SP and the hydraulic conductivity were shown at 20% and 50% of the silt weight fraction, respectively. Although there are difference between these transition thresholds, these two coefficients show a specific correlation. In the future, additional study should be conducted for detailed analysis of the threshold transition values between SP and hydraulic conductivity.

• Clean Technology
• /
• v.24 no.2
• /
• pp.112-118
• /
• 2018

Thermo-responsive polymers that exhibit phase transition in response to temperature change can be used as materials for smart windows because they can control solar light transmission depending on the outside temperature. The development of thermo-responsive polymers for smart windows that can be used over a wide temperature range is desirable. To obtain high performance smart windows materials, three-dimensional thermo-responsive poly(N-isopropylacrylamide) (PNIPAm) gels were prepared by free radical polymerization from monomer N-isopropylacrylamide, N, N'-methylenebis acrylamide (MBAm) as a crosslinking agent, ammonium persulfate (APS) as a strong oxidizing agent/tetramethylene diamine as a catalyst, and a mixture of two solvents (water/glycerol). This study examined the effect of glycerol content on the lower critical solution temperature (LCST), freezing temperature and the solar light transmittance of crosslinked PNIPAm gel films. The LCST and freezing temperature of PNIPAm gel films were found to be significantly decreased from 34.3 and $6.3^{\circ}C$ to 28.2 and $-6.5^{\circ}C$ with increasing glycerol content from 0 wt% to 10 wt%, respectively. It was found that the transparent PNIPAm gel films at $25^{\circ}C$ (temperature < LCST) were converted to translucent gels at higher temperature ($45^{\circ}C$) (temperature > LCST). These results suggested that the crosslinked PNIPAm gel materials prepared in this study could have high potential for application in smart glass materials.

• Journal of the Korean Chemical Society
• /
• v.42 no.1
• /
• pp.84-91
• /
• 1998

Random copolymers of N-isopropyl acrylamide (NIPAAm) and acrylic acid (AAc) which exhibit temperature- and pH-responsive behavior were synthesized by free-radical polymerization. The copolymers were characterized by means of FT-IR spectrometry and titration. The influence of polyelectrolyte on the lower critical solution temperature (LCST) of pH/temperature-sensitive polymers was investigated in the pH range of 2-12. The LCSTs of PNIPAAm/water in poly(NIPAAm-co-AAc) were determined by cloud-point measurements. A polyelectrolyte complex was prepared by mixing poly(NIPAAm-co-AAc) with poly(allylamine) (PAA) or poly(L-lysine) (PLL) solutions as anionic and cationic polyelectrolytes, respectively. Back titration was performed to determine the content of AAc and to study the effect of comonomer ionization on the LCST. The LCSTs of PNIPAAm/water in the copolymers were strongly affected by pH, presence of polyelectrolyte, AAc content, and charge density on the polymer. The polyelectrolyte complexes were formed at neutral condition. The influence of more hydrophobic PLL as polyelectrolyte on the cloud-point of PNIPAAm/water in the copolymer was stronger than that of poly(allylamine) (PAA).

• Korean journal of applied entomology
• /
• v.29 no.4
• /
• pp.217-221
• /
• 1990

Some biological phenomena of Anagrus incarnatus Haliday, an egg parasitoid of planthopper, were studied under three different constant temperatures. Duration from egg to adult emergence of the parasitoid from the BPH eggs were 21.5, 13.6 and 10.6 days under $20^{\circ}C$, $25^{\circ}C$ and $30^{\circ}C$, respectively. Rate of the development was highly correlated with temperature. The critical temperature was estimated as $10.0^{\circ}C$ and the effective degree days was 210.3 day-degree. Durations for the development of A. incarnatus under 25$\pm$$1^{\circ}C$ (16L : 8D) were 12.4, 12.5 and 12.1 days from eggs of N. lugens, S. furcifera and L. striatellus, respectively. Duration of the development of A. incarnatus from 1, 3, 5, 7 days old BPH eggs were 12.5, 12.1, 12.9 days, respectively. The average longevity of adult was 5.3 days under 25$\pm$$1^{\circ}C$. Number of the ovarian and practically oviposited eggs were 34.8$\pm$28 and 28.3$\pm$0., respectively. Female A. incarnatus laid most of the eggs within few days after the emergence ; over 60% within 24 hours, nearly 90% upto the 2nd day, and nearly 100% upto the 3rd day.

• Korean Journal of Ecology and Environment
• /
• v.45 no.1
• /
• pp.123-128
• /
• 2012

We aimed to estimate the accumulated degree days required for the development of $Cloeon$ $dipterum$ (Ephemeroptera: Baetidae) in an experimental tub under field conditions from August 7 to October 10 in 2011. After 4 days in a tub setting, a dead female adult was found on the water surface at which oviposition had presumably occurred. Adults emerged from 39 days to 61 days after the oviposition date. The total number of emerged adults was 229, and the sex ratio (number of females : total population) was 0.45, although not statistically significant ($p$ >0.05). The males generally emerged earlier than females. Assuming that the basal temperature ($T_b$) value is $0^{\circ}C$, we estimated the number of accumulated degree days required for the development of $C.$ $dipterum$ to be $1,221.8{\pm}116.0$ DD (mean${\pm}$SD). Since the annual number of accumulated degree days in the reference wetland was measured to be 5,650.0 DD, we estimated that $C.$ $dipterum$ is multivoltine, with a maximum of 4 cohorts in 1 year in natural habitats.

• Fire Science and Engineering
• /
• v.22 no.1
• /
• pp.99-104
• /
• 2008

It is important to understand thermal characteristic as a method to estimate the new materials, because spontaneous ignition characterized by causing combustion in the low temperature without ignition source. If can not find out the thermal characteristics of materials, it is frequent that causes of fires could not be found. The danger level of spontaneous ignition material should be estimated and by closely studying its thermal characteristic. However, RPF(Refuse Paper & Plastic Fuel) is a solid matter and getting increasesa year by year because it is an economy profit as alternative energy for limited fossil fuels. Some time RPF occur a fire in the cases of its production process and conservation. Therefore study for thermal stability and critical ignition temperature of RPF was so imperative that the experiment by means of Bombe Calorimeter, TG-DTA, MS80, SIT-II, and Wire Basket Test was implemented. As a result, RPF had a caloric value 26.4-28.3 MJ/kg, and its initial pyrolysis temperature was $192^{\circ}C$ at heating rate 2 K/min. With the result of analysis by MS 80 which is an instrument measuring microscopic calory, pure RPF not containing water has higher caloric value than RPF containing 20% water. Also, SIT-II which is an instrument of insulated auto-ignition was ignited by $118.5^{\circ}C$. This temperature is lower than that of Wire Basket Test. The critical ignition temperature was calculated by Frank-Kamenetskii equation can cause ignition at $80^{\circ}C$ when conserved in the height of 10 m by the standard of infinity slab.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.98-104
• /
• 2007

The expansion behavior of polystyrene (PS) chains with various molecular weights has been investigated above Flory $\Theta$temperature by viscometry after dissolving in the three different mixed solvents systems such as benzene/n-heptane, 1,4-dioxane/isopropanol, and 1,4-dioxane/n-heptane. Two different regimes are observed as increasing temperature: one regime is for the expansion of chain and the other is for the contraction. For the higher molecular weight sample of PS, the higher peak temperature showing its maximum expansion is obtained. Within a certain system of Ps/mixed solvents, the $\tau/\tau_c$ parameter shows universality for the variation of molecular weight. But while each system of Ps/mixed solvents has shown its own different slope, the universality breaks down in the overall system of mixed solvents. However after introducing a new empirical $b^{2/3}\tau/\tau_c$ parameter, all data points of three different systems have dropt on one master curve and the universality of chain expansion has recovered again. Here $\tau$ and $\tau_c$ are defined as $(T-\Theta)/\Theta$ and $(\Theta-T_c)/T_c$, respectively and $T_c$ is the critical solution temperature, and b of Schultz-Flory equation is corresponding to the effective slope in the plot of $1/T_c$ against $1/M_w^{1/2}$.

• Journal of agriculture & life science
• /
• v.53 no.2
• /
• pp.121-129
• /
• 2019

This study carried out to determine control factors for the improvement of productivity of laying hens suffering heat stress during hot weather. A total of 48,451 ISA Brown layers were housed in a farm located in Gyeongsangnam-do, Republic of Korea. Five thermo-hydrometer loggers were installed inside the house to collect data of dry-bulb temperature and relative humidity. The experiment continued for 81 days when the summer season begins from 19th June to 7th September, 2018. This study analyzed the correlations among layers' production index and daily average, highest, and lowest temperature; daily average, highest, and lowest relative humidity; and daily average, minimum, and maximum THI. The result indicated that feed consumption, hen-day egg production, egg weight, and FCR decreased as the daily average, highest and lowest dry-bulb temperature and THI rise (p<0.01). On the other hand, water intake increased as the daily average, highest and lowest dry-bulb temperature and THI rise (p<0.001). The relative humidity was not considered to have direct correlations to the layers' production index (p>0.05). However, it was noticeable that the mortality did not have significant relations with daily average and highest temperature; THI; or daily average, highest and lowest relative humidity while it was relevant to the daily lowest temperature and THI (p<0.05). In conclusion, to enhance the productivity of laying hens in a hot climate, it is recommended that daily average, highest, and lowest dry-bulb temperature and THI are maintained as low as possible. Especially, the daily lowest temperature is needed to lower to 20℃, which is the lowest critical temperature for layers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.808-816
• /
• 2012

This paper is the study for the directional solidification of the ingot through the thermal analysis simulation and structural change of casting furnace. With the results of thermal analysis simulation, the silicon as a whole has reached the melting temperature as the retention time 80 min. The best cooling conditions showed at the upper cooling temperature $1,400^{\circ}C$ and cooling time 60min. The fabricated wafers showed the superior etching result at the grain boundary than that of existing commercial wafers. The FTIR measurements of oxygen and carbon impurities were not in the critical value for solar conversion efficiency. The NAA analysis of metal impurities were also detected the total number of 18 different metals, but the concentration distribution showed no significant positional deviations in the same position from the top to the bottom.

• Applied Chemistry for Engineering
• /
• v.4 no.3
• /
• pp.601-615
• /
• 1993

A series of polycarbonate(PC)/polyamide 6(PA6) blends were prepared by three different blending methods to investigate their compatibility. From the DSC results, all of these blends have two Tg's in their own Tg regions, and there was no significant depression of the melting point and the crystallization temperature of PA6. With respect to the microstructure of the blends by SEM, the phase separation occurred at very low blend compositions, PC/PA6=95/5 and 5/95, already. In addition, a method is proposed to determine the Flory-Huggins polymer-polymer interaction parameter(${\chi}_{12}$) in polymer blend systems by using the experimentally determined Tg's. The values of ${\chi}_{12}$ obtained were 0.0381, 0.0411, 0.0418, for solution casting, solution precipitation, and extrusion blending methods, respectively. These values were higher than the critical value of ${\chi}_{12}$,($({\chi}_{12})_c$, 0.0271). Therefore it was concluded that the PC/PA6 blend system have little compatibility.