• Korean Journal of Materials Research
• /
• v.1 no.1
• /
• pp.54-61
• /
• 1991

YBCO films deposited on MgO(100) and Si(100) by rf-magnetron sputtering using stoichiometric single target were annealed under oxygen atmosphere at $880^{\circ}C$ for 1 hr. The microstructure and superconducting properties of YBCO thin films depended on the composition of pre-annealed thin films. Basal planesuperconducting particles grown on MgO(100) substrate had small and rod-like shade due to preferred orientation, while superconducting film grown on the basal plane-superconducting particles showed round-shape particles. If pre-annealed thin film had nonstoichiometric composition, liquid phase was formed during the heat treatment, which made it easy for particles to grow in the preferred orientation and thus to form textured structure. But the thin films with the textured structure did not show good superconducting properties, especially $T_c$, since the liquid phase transformed into second phase in the grain boundary during the cooling. The effect of the second phase on $T_{c, \;zero}$ was greater than that on $T_{c, \;on}$.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.639-644
• /
• 1996

The $YBa_2Cu_{3-y}Ag_yO_{7-x}$ high-temperature superconductors were prepared by pyrophoric synthetic method from $Y_2O_3$, $BaCO_3$, CuO, and $AgNO_3$ powders. When we were partially substituted Ag for Cu in $YBa_3Cu_3O_{7-x}$, the superconducting properties of $YBa_2Cu_{3-y}Ag_yO_{7-x}$ were investigated with X-ray diffractometer, resisitivity measuring equipment, SEM, and Vickers Hardness. The Tc,zero of $YBa_2Cu_3O_{7-x}$ was 91K, the density was $5.2g/cm^3$, and the hardness was $590kg/mm^2$. When Ag was substituted below y=0.15, electrical property of $YBa_2Cu_{3-y}Ag_yO_{7-x}$ did not change but microstructure, density, and hardness were enhanced.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1083-1091
• /
• 1997

As one of the chemical powder fabrication methods, the powder preparation method by using oxalate has the following advantages; (1) easy to control the chemical stoichiometry, (2) easy to fabricate homogeneous and fine particles, and (3) easy to be thermaly decomposed at low temperature. In the present study, the initial morphology and size distribution of the powder were controlled and the homogeniaty was improved. By carefully controlling the pH with NH4OH, the Bi(Pb)-Sr-Ca-Cu-O superconducting powders were prepared and investigated for their properties. The microstructures and the superconducting properties of the pelletized samples were investigated. Also, the microstructures and electrical properties of the samples prepared by tape casting method were investigated. The fabricated powders were spherical with less than 400 nm, but most of them were agglomerated to be 1~3 ${\mu}{\textrm}{m}$ in size. The critical temperature of the pelletized sample annealed at 84$0^{\circ}C$ for 72 hours in air was 110K. And the critical currents of annealed samples in air prepared by tape casting process for 24 hours and 72 hours were 0.6 A (Jc=600A/$\textrm{cm}^2$) and 1.9A (Jc=1, 900A/$\textrm{cm}^2$) respectively.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.3
• /
• pp.67-72
• /
• 2006

Several propellants were investigated experimentally for ignition characteristics in subatmospheric pressure. The threshold ignition pressure was 4 psia for HTPB/AP composite propellant. The partial replacement of AP in HTPB/AP propellant by $5{\sim}l5%$ of HMX, HNIW showed that the improvements in ignition delay was over 50% and the threshold pressure was below 0.4 psia. This appears to be due to the characteristics of HMX and HNIW exothermic dissociated at the temperature(${\sim}220^{\circ}C$) love. than that of AP. The ignition substance $B/KNO_3$ was coated thinly on the propellant surface for better ignition performance. As a result, ignition delay time of 15% was improved. NC is applied to $B/KNO_3$ ignition substance as a secondary binder and $NC-B/KNO_3$ suspension solution is coated to the propellant surface.

• Elastomers and Composites
• /
• v.35 no.2
• /
• pp.149-156
• /
• 2000

trans-octylene rubber(TOR) was melt-blended with an incompatible NBR/EPDM (70/30) blend. Mixing torque and temperature were reduced as TOR was added to the NBR/EPDM blend. Rheometer results indicated that TOR participated in vulcanization and became a part of network. A scanning electron micrograph demonstrated that EPDM was dispersed in NBR matrix in the blend and the addition of TOR led to a finer dispersion of EPDM particles. On the addition of TOR, the tensile strength, the tensile strain as well as the modulus of the blend vulcanizates increased. The ozone resistance of the blends determined in terms of critical stress-strain parameter was significantly enhanced in the blend as TOR was added. Improvements in the properties were believed to be associated with fine morphology and the increase in crosslink density due to the chain entanglement of the ternary blends.

• Fire Science and Engineering
• /
• v.30 no.5
• /
• pp.116-123
• /
• 2016

The quantitative risk assessment methods for thermal failure in targets were studied using fire modeling. To this end, Fire Dynamics Simulator (FDS), as a representative fire model, was used and the probabilities related to thermal damage to an electrical cable were evaluated according to the change in fire area inside a specific compartment. 'The maximum probability of exceeding the damage thresholds' adopted in a conservative point of view and 'the probability of failure' including the time to damage were compared. The probability of failure suggested in the present study could evaluate the quantitative fire risk more realistically, compared to the maximum probability of exceeding the damage thresholds with the assumption that thermal damage occurred the instant the target reached its minimum failure criteria in terms of the surface temperature and heat flux.

• Membrane Journal
• /
• v.20 no.4
• /
• pp.297-303
• /
• 2010

Composite membranes were prepared for membrane/cold condensation process for recovery of unreacted olefin monomer from the polyolefin polymerization process by solution coating and plasma polymerization processes. Poly(dimethylsiloxane) (PDMS) solution was coated on polysulfone (PSF) support and increase of prepolymer content in solution made more dense membrane structure to result in the increase of separation factor while absolute flux decreased. Permeation of organic materials through the composite membranes follows the sorption and diffusion mechanism, which brought about the results that separation factor increased with critical temperature of the organic materials, and that flux increased with the increase of the molar volume. Crosslinking period affected the permeation characteristics. Other types of composite membranes were fabricated by plasma polymerization of siloxane materials on polypropylene (PP) and PSF supports. PP was tested as a support for composite membranes, which had not been used so far in solution coating process, and plasma polymerization made the composite membranes equivalent performances to those of membranes prepared by solution coating process.

• Journal of the Korean Chemical Society
• /
• v.36 no.6
• /
• pp.818-823
• /
• 1992

2-Ethylhexanoate compounds which contained Y, Er, Yb, Ba, and Cu were prepared separately. These metallo-organic compounds were dissolved together in the common solvent and the solution was homogeneous. From these solution, high $T_c$ superconductors $YBa_2Cu_3O_{7-\delta}(Y_{123})$, $ErBa_2Cu_3O_{7-\delta}(Er_{123})$, and $YbBa_2Cu_3O_{7-\delta}(Yb_{123})$ were prepared. XRD analysis showed that these superconductors were not single phase and contained some impurity phases including $YBa_2Cu_4O_8(Y_{124})$. This was also confirmed from the magnetic susceptibility measurement. Generally, critical temperatures were higher than that of the superconductors prepared by ceramic method. Volume diamagnetic susceptibility showed little variation compared to the specimen made by ceramic method.

• Nuclear Engineering and Technology
• /
• v.13 no.3
• /
• pp.121-129
• /
• 1981

Three most outstanding maximum flow rate formulas are identified from many existing models. Outlines of the three limiting mass flow rate models are given along with computational procedures to estimate approximate amount of fission products released from a containment to environment for a given characteristic hole size for containment-isolation failure and containment pressure and temperature under a loss of coolant accident. Sample calculations are performed using the critical ideal gas flow rate model and the Moody's graphs for the maximum two-phase flow rates, and the results are compared with the values obtained from the mass leakage rate formula of CONTEMPT-LT code for converging nozzle and sonic flow. It is shown that the critical ideal gas flow rate formula gives almost comparable results as one can obtain from the Moody's model. It is also found that a more conservative approach to estimate leakage rate from a containment under a LOCA is to use the maximum ideal gas flow rate equation rather than tile mass leakage rate formula of CONTEMPT-LT.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.2
• /
• pp.61-70
• /
• 2023

This paper examines the way of thinking and limitations of physicists regarding the phenomenon of superconductivity and outlines how room-temperature and ambient-pressure superconductors can be developed through the statistical thermodynamic background of the liquid state theory. In hypothesis, the number of electron states should be limited by confining them to a state close to one-Dimension. Simultaneously, the electron-electron interactions should be frequent enough for the electrons to have liquid-like properties. As an example of implementing the hypothesis, our team reports the development of room-temperature and ambient-pressure superconductivity of a material named LK-99 (superconducting compound name developed in the research), whose structure was revealed through numerous experiments with a clue found by chance. Moreover, we summarize the theoretical and experimental basis for the characteristics and discovery of the world's first superconducting material surpassing the critical temperature of 97℃ at atmospheric pressure.