• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.1-8
• /
• 2008

Seoul metropolitan government has introduced Bus Rapid Transit (BRT) systems in some major urban corridors on July 1st, 2004, and has reported that it was successful on the ground that bus speed has been increased in the corridors with BRT system and that it has also resulted in the increase of bus patrons. However, there comes a negative claim that BRT has increased the number of fatalities in the same corridors. This study first aims at developing safety evaluation indicators of pedestrian crossings, then compares values of those indicators from pedestrian crossings with and without BRT systems. The safety evaluation indicators of pedestrian crossing are developed as: the number (or ratio) of conflicts between pedestrians and vehicles, the number (or ratio) of vehicles violating pedestrian signals, the number (or ratio) of pedestrians remaining crossings at red signals, and the number (ratio) of pedestrians walking beyond crossing areas. When we compare values of these indicators for both pedestrian crossings with and without BRT system, it has turned out that crossings with BRT systems has more number of conflicts than the crossings without BRT systems, but it cannot be said that the ratio of conflicts will be different between two crossing types. It means that the number of conflict will increase as the number of pedestrians and vehicles in the crossings. When we note that BRT system intrinsically attract more number of pedestrians who get-in or get-off bus stops, we cannot said that BRT system will be safer for pedestrians.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.85-85
• /
• 2011

기존 과속단속카메라의 한계와 더불어 차량의 속도 거동이 더욱 순화될 필요가 제기됨에 따라 국내에서는 2007년 12월 16일 영동고속도로 둔내터널에서 처음 구간과속단속시스템을 도입하였다. 현재 고속국도 6개소를 포함하여 총 8개소에서 구간과속단속시스템을 운영하고 있다. 하지만 해당 시스템의 도입효과가 명확하지 않아 시스템의 효과에 대한 의문도 꾸준히 제기되고 있다. 본 연구에서는 미국 Los Alamos연구에서 개발된 TRANSIMS(TRansportation Analysis and SIMulation System)의 시뮬레이션 결과를 이용해 시스템 적용 전 후의 거시적 교통류 특성을 수집하여 효과에 대하여 분석하였다. 본 연구에서는 구간과속단속시스템의 효과를 분석하기 임의의 네트워크를 제작하여 모의실험을 해 보았다. 네트워크는 총 연장 12km의 직선형 구간으로 제작하였다. 모의실험에 사용되는 링크의 Cell크기는 3m로 설정하여 TRANSIMS의 내정값인 7.5m보다 더욱 상세한 결과가 나오도록 설정하였다. 링크는 편도 3차로로 설정하여 모의실험을 실시하였으며, 구간단속이 미치는 영향을 실제와 유사하게 적용하기위해 모의실험을 하는 링크의 제한속도를 구간단속 실시 전에는 160km/h, 실시 후에는 100km/h로 설정하였다. 구간단속 실시 전 링크의 제한속도를 160km/h로 높게 설정한 것은 실제 통행이 발생하는 속도를 구현하기위해서이며, 차종별 최대 속도를 제한하여 속도분포를 나타내었다. TRANSIMS를 통한 구간과속단속시스템의 효과를 분석하는 모의실험 결과 그림 1의 그래프에서 나타나는 것과 같이 구간단속 전 후에서 속도저감효과가 나타나는 것을 확인 할 수 있었다. 특히, 교통류율이 낮을 때 속도가 높게 나타나던 부분이 구간단속 실시 후 속도가 낮아지는 것을 보아 실제로 교통류율이 낮은 고속국도에서는 높은 효과를 기대할 수 있다고 판단된다. 표 1에서 구간단속 전 후의 주행차량의 속도변화를 살펴보면 과속운행의 비율이 상당히 주는 것을 확인할 수 있다. 이러한 특성 때문에 교통량이 비교적 적은 고속국도에서는 뛰어난 효과를 발휘할 것이라고 예상된다.

• Journal of Korean Society for Geospatial Information Science
• /
• v.5 no.2 s.10
• /
• pp.131-144
• /
• 1997

Traffic jam densified day by day is phenomenon to occur lack of the road capacity in comparison with traffic density, but lack of the road cannot be concluded by main cause of traffic ism. Because the central function of a city would be concentrated upon the downtown and traffic demand would not be evenly distributed by the classification of an hour. Therefore, this study based on the fact that each driver will select the route generating traffic delay very low when path choice from origin to destination in travel plan estimating the quality of passage could be maintained the speed he want will approach to a characteristic grasp of a road, traffic, driver changing every moment by traffic-demand of road increased as a geometrical series with analysis a classification of a street, a intersection along the path on traffic density and highway capacity analysis the path using GIS techniques about complex street network, also will get the path of actual optimum for traffic delay trend creating under various condition the classification per a hour, a day of week and an incident through network such as analysis for traffic generation zone adjacent about street, intersection, afterward will expect the result increasing efficiency of the road-use through a good distribution of traffic by optimum-path choice, accordingly will prepare the scientific, objective, appropriate basis to decide the reasonable time of a road-widen and expansion through section analysis along a rate of traffic volume vs. road capacity.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.1-9
• /
• 2007

To decide the number of road lane is very important and related to the 30th design hourly factor in the design of transportation facilities. But, as the quantitative division of road types is difficult, most planner and designer for deciding the 30th design hourly factors have used the fixed values in our country. In this study, we have analyzed the time series property of the design hourly factors in national highways and developed the model capable of estimating the 30th design hourly factors using real data. The presented model is a simple regression model(DHV = K*AADT), which is applied to the division of road lanes(2 or 4 lanes) and the level of AADT(3 levels). As a results, the simple regression model have better performance than the existing method with respect to MAPE and $R^2$. Also, the variations of the 30th design hourly factors are small. The more traffic volume increase, the more the factors decrease. But, the limitation of this study is to use the exiting method estimating the values of the factors, it is subject to study hereafter.

• International Journal of Highway Engineering
• /
• v.6 no.3 s.21
• /
• pp.1-7
• /
• 2004

Roads, like bikeways, parkways and walks, are to be just capable of supporting light traffic and traveling public, but they are required to be human friendly and environmental-oriented. Lately soil-solidifier mixture, a kind of soil-cement, has developed and has been applied to the recycling and environment-oriented pavement as the surfacing material. Soil-solidifier pavement structure has been designed by only experience. To design this pavement mechanically, it is necessary to find out basic engineering properties of soil-solidifier mixture. This study focuses on finding out mechanical characteristics of the mixture according to mixture proportions and aging. Test molds with various mixture proportions are made, and then unconfined strength tests are performed for test molds with aging of the mixture. As the result of this study, it is found that the strength of the mixture increases with amount of cement and that maximum strength is achieved at 6%$\sim$8% of the ratio of solidifier and water. The strength increase rapidly until 14 days, after then slowly. After 28 days the strength of the mixture approaches to the constant value. The heat of hydration during curing of the mixture is measured no significantly. It also shows that temperature characteristics of the mixture is similar to that of soil. Since this mixture is mixed with soil and is able to improve engineering problems in pavement due to temperature, this mixture is expected to use effectively in the environment-oriented pavement for light traffic.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• autumn
• /
• pp.180-185
• /
• 2003

The increase of traffic over a bridge has been emerged as one of the most severe problems in view of bridge maintenance, since the load effect caused by the vehicle passage over the bridge has brought out a long-term damage to bridge structure, and it is nearly impossible to maintain operational serviceability of bridge to user's satisfactory level without any concern on bridge maintenance at the phase of completion. Moreover, bridge maintenance operation should be performed by regular inspection over the bridge to prevent structural malfunction or unexpected accidents front breaking out by monitoring on cracks or deformations during service. Therefore, technical breakthrough related to this uninterested field of bridge maintenance leading the public to the turning point of recognition is desperately needed. This study has the aim of development on automated inspection system to lower surface of bridge superstructures to replace the conventional system of bridge inspection with the naked eye, where the monitoring staff is directly on board to refractive or other type of maintenance .vehicles, with which it is expected that we can solve the problems essentially where the results of inspection are varied to change with subjective manlier from monitoring staff, increase stabilities in safety during the inspection, and make contribution to construct data base by providing objective and quantitative data and materials through image processing method over data captured by cameras. By this system it is also expected that objective estimation over the right time of maintenance and reinforcement work will lead enormous decrease in maintenance cost.

• Clean Technology
• /
• v.25 no.1
• /
• pp.19-32
• /
• 2019

As regional air pollution gets worse by the sulfur oxides emitted from various types of vessels passing through the many countries, the International Maritime Organization establishes the emission control areas and regulates sulfur dioxide in those areas. In order to satisfy these regional regulations, the fuel selection method and the exhaust gas post-treatment device are applied to the ships. Due to the economic reasons, the post-treatment method of exhaust gas for reducing the amount of sulfur oxides discharged is mainly preferred. The scrubber which is dominantly used in the ships are the spray type system where the sprayed liquid drops used for capturing the soluble sulfur dioxides in the exhaust gas. The performance of the spray type system depends on the size distribution of the sprayed droplets. In order to evaluate this performance, we designed counterflow type scrubber and cyclone scrubber and evaluated the desulfurization efficiency and the amount of droplet evaporation according to the size of each droplet by using computational fluid dynamics. The Eulerian-Eulerian analysis method was used because the scrubber had a gas-liquid two-phase flow inside the scrubber. When the diameter of the droplet was $100{\mu}m$, $300{\mu}m$, $500{\mu}m$ and $700{\mu}m$. As a result, both of scrubbers showed high desulfurization efficiency and low evaporation amount at $500{\mu}m$ and $700{\mu}m$.

• Journal of Korean Society of Transportation
• /
• v.34 no.2
• /
• pp.123-134
• /
• 2016

Traffic accident at intersections takes 44.3% of total number of accidents on entire road network of Korea in 2014. Although several studies addressed contributory factors of accidents at signalized intersection, very few is known about the factors at rural unsignalized intersections. The objective of this study is therefore to investigate specific characteristics of crashes at rural unsignalized intersection and to identify contributory factors in causing crashes by statistical approach using the Ordered Logistic Regression Model. The results show that main type of car crashes at unsignalized intersection during the daytime is T-bone crashes and the number of crashes at 4-legged intersections are 1.53 times more than that at 3-legged intersections. Most collisions are caused by negligence of drivers and violation of Right of Way. Based upon the analysis, accident severity is modeled as classified by two types such as 3-legged intersection and 4-legged intersection. It shows that contributory factors in causing crashes at rural unsignalized intersections are poor sight distance problem, average daily traffic, time of day(night, or day), angle of intersection, ratio of heavy vehicles, number of traffic violations at intersection, and number of lanes on minor street.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.282-288
• /
• 2023

In this study, we analyzed the amount of roadside fine dust generated from newly constructed specially modified asphalt pavement and general asphalt pavement from existing roads. We collected the 1,000 g (100 g/day) of dust samples from the roadside of the express bus terminal and commercial facility area in Chungcheongnam-do's C site at three-day intervals during the summer of 2022 and 2023. The collected samples were separated from fine dust according to size in the 75-150 ㎛ range and, were separated only from Tire and Road Wear Particles through density separation. No.1-3 are general asphalt pavement section as an existing road. Fine dust and Tire and Road Wear Particles in No.1-3 were 24.27 g, 24.36 g, 0.53 g, and 0.53 g, respectively, and the quantitative results for 2022 and 2023 were similar. On the other hand, No.4-6 are newly constructed specially modified asphalt pavement section. Fine dust decreased by 14.8 % and tire and road wear particles decreased by 29.6 % in 2023 compared to 2022 in No.4-6. In addition, according to the results of thermogravimetric analysis, Tire and road wear particles in No.1-3 are tire and road components at 30 % and 70 %, respectively. And Tire and road wear particles in No.4-6 are tire and road components at 35 % and 65 % in 2023, respectively. From these results, it was confirmed that the newly constructed specially modified asphalt pavement can be effective in reducing roadside fine dust and Tire and Road Wear Particles. However, there may be some shortcomings in conclusive research results due to limited space and sample collection period. In the future, we plan to conduct various case studies.

• Korean Journal of Agricultural Science
• /
• v.6 no.2
• /
• pp.166-184
• /
• 1979

In order to prevent the water loss in the irrigation canal constructed on the sandy gravel layer or on the other highly permeable ground layer, lining has been practiced. Many studies have been done so far on the lining method to prevent the water loss in the irrigation canal and recently studies on the lining with plastic film or polyethylene film were also reported. However, the plastic film or polyethylene film has low strength and is liable to break, and water loss from pin hole caused by contacting with sand or gravel is highly predicted. This study was then conducted to find proper lining and buring method in canal construction of polypropylene mat after coated with vinyl, as one way to overcome the shortcoming frequently observed when plastic or usual polyehtylene film were used. Eventhough rather longer periods of experiments are needed to attain reliable and accurate results on the variation of durability, the durability of asphalt coated area, or on the damage due to freeze after burial or exposure of polypropylene mat, the experiemental results obtained during one year of period are summarized as follows: 1. The curvature at the area between canal bottom and side slope had increased stability and saved consruction cost. The relationship among the variation of curvature, the reduction of polypropylene mat and the reduced amount of soil cutting at each side slope was presented in Fig. 7 through 9. 2. The depth of covering material to protect polypropylene mat was desired to be over 30cm, considering the water depth, side slope, canal cleaning practices, traffic, or back pressure of irrigation period. 3. In order to increase the canal stability and to prevent slope erosion, sandy soil was required, to be placed under ground, and coarse gravel should cover the surface area of canal. 4. The studies on the stability of side slope in the canal should consider the passive area on the bottom and the slope should be about 1 to 2, considering the slope stability, allowable velocity and tractive force. 5. When compared with earth lining, the lining with polypropylene mat coated with vinyl was responsible to save 28% and 37% of canal lining cost, when the soil carrying distances were 500 and 700m. respectively. 6. The water interception was almost completely attained when the polypropylene mat coated with vinyl was used for lining. But further studies were assumed to be necessary for the use of asphalt since the strength of polypropylene mat connected with asphalt will vary with duration.