• Title/Summary/Keyword: 일방향 기구

Search Result 7, Processing Time 0.021 seconds

Fundamental Study for Ocean Wave Energy Converter Using a Rack-Pinion Gear Based One-way Mechanism (일방향 기구 기반 랙-피니언 기어를 이용한 병진형 파력발전장치에 대한 기초연구)

  • Lee, Junkyoung;Cho, Sungil;Lee, Sehan;Lee, Sangchun;No, Hyunchul
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2011.05a
    • /
    • pp.167.1-167.1
    • /
    • 2011
  • Sustainable energy generation is becoming extremely imperative due to the expected limitations in current energy resources and to reduce pollution. Especially, because of its considerable energy potential, ocean wave energy has been investigated with regard to power generation. To develop large high power wave generator system, it is important to make a small scale proto type and to test that. Thus the objective of this research is to examine the characteristics of a mechanically excited generator system having small power capacity experimentally. The water reservoir (4 m length, 1.5 m width and 1.8 m depth) having a wave maker to make arbitrary height and period of the water wave was made. The proto type consists of three main parts; a buoy, rack-pinion base one-way mechanism, and a wave generator(Fig.1). The water wave is going up and down and the hexahedron buoy is following the wave. The rack gear attached to the buoy is also going up and down to roll the pinion connected to an electric generator then it produces electricity. The experiments were performed with several conditions of water waves, and the power outputs over 30 W could be measured for some conditions. In future works, to achieve higher performance for the proto type, the effects of primary parameters (buoy shape and mass, etc.) on the system efficiency will be identified.

  • PDF

Prediction of Residual Strength of CFRP Subjected to High Velocity Impact (고속충격을 받는 CFRP 복합재료의 잔류강도 예측)

  • 박근철;김문생
    • Transactions of the Korean Society of Mechanical Engineers
    • /
    • v.18 no.3
    • /
    • pp.600-611
    • /
    • 1994
  • The purpose of this research is to propose a model for the prediction of residual strength. For this purpose, two-paremeter model based on Caprino's is developed and formulated by the ratio of indentation due to impact and normalized residual strength. The damage zone is considered only as an indentation. Impact tests are carried out on laminated composites by steel balls. Test material is carbon/epoxy laminate. The specimens are composed of $[{\pm}45^{\circ}/0^{\circ}/90^{\circ}]_2$ and $[\pm}45^{\circ}]_4$ stacking sequence and have $0.75^T{\times}0.26^W{\times}100^L(mm) dimension. A proposed model shows a good correlation with the experimental results And failure mechanism due to high impact velocity is discussed on CFRP laminates to examine the initiation and development of damage by fractography and ultrasonic image ststem. The effect of the unidirectional ply position on the residual strength is considered here.

A Numerical Analysis for Optimal Design of Road Generator System (도로용 발전장치 최적화 설계를 위한 수치해석)

  • Lee, Suk Young
    • Journal of Energy Engineering
    • /
    • v.23 no.3
    • /
    • pp.163-173
    • /
    • 2014
  • In this study, a modeling method is based on representing a road generation system with several rigid bodies, i.e, pad, shaft, torsional damper, oneway-clutch, gear system, and electricity generator. The simulation software is developed to evaluate the performance of a road generation system. It is used to determine parametric dimension for optimal design with the theoretically calculated results from the simulation software. The parametric dimensions are included as capacity, length, and angle of equipment. The transient responses at the conditions of low and high vehicle speed are compared with the calculated results as torque, power, out energy etc. Consequently, before manufacturing system, the analysis of simulation results shows that the proposed concept and system has efficiency and confidence.

Fabrication of unidirectional commingled-yarn-based carbon fiber/polyamide 6 composite plates and their bend fracture performances (일방향 혼합방사형 탄소섬유/폴리아미드 6 복합재료판의 제작조건과 굽힘파괴거동)

  • Choi, Nak-Sam
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.22 no.2
    • /
    • pp.416-427
    • /
    • 1998
  • Unidirectional commingled-yarn-based carbon fiber(CF)/polyamide(PA) 6 composite was fabricated under molding pressures of 0.4, 0.6 and 1.0 MPa to study its flexural deformation and fracture behavior. Fiber/matrix interfacial bonding area became larger with an increase of molding pressure from 0.4 to 0.6 MPa. For molding pressures .geq. 0.6 MPa, good flexural performance of similar magnitudes was attained. For the fracture test, four kinds of notch direction were adopted : edgewise notches parallel (L) and transverse (T) to the major direction of fiber bundles, and flatwise notches parallel(ZL) and perpendicular(ZT) to this direction. Nominal bend strength for L and ZL specimens exhibited high sensitivity to notching. ZL specimens revealed the lowest values of the critical stress intensity factor $K_c$ which was slightly superior to those of unfilled PA6 matrix. Enlargement of the compression area for T specimens was analyzed by means of the rigidity reduction resulting from the fracture occurrence.

Temperature Dependent Creep Properties of Directionally Solidified Ni-based Superlloy CM247LC (일방향 응고 니켈기 초내열 합금 CM247LC의 온도에 따른 크리프 특성)

  • Choi, Baig-Gyu;Do, Jeonghyeon;Jung, Joong Eun;Seok, Woo-Young;Lee, Yu-Hwa;Kim, In Soo
    • Journal of Korea Foundry Society
    • /
    • v.41 no.6
    • /
    • pp.505-515
    • /
    • 2021
  • Creep properties of directionally solidified Ni-based superalloy CM247LC under various temperature and stress conditions have been investigated. In the heat-treated specimen, some portion of eutectic γ-γ' remained, and uniform cubic γ' was observed in the dendrites. At low temperature (750℃) and high stress condition, a large amount of deformation occurred during the primary creep, while the tertiary creep region accounted for most of the creep deformation under high temperature and low stress condition. γ' particles are sheared by dislocation dissociated into super lattice partial dislocations separated by stacking faults at 750℃. No stacking faults in γ' were found at and above 850℃ due to the temperature dependence of the stacking fault energy. Raft structure of γ' was found after creep test at high temperature of 950℃ and 1000℃. At 850℃, the deformation mechanism was shown to be dependent on the stress condition, and so rafting was observed only under low stress condition.

Problems of Metallic Dental Instruments for Dental Use (치과에서 사용되는 금속치과기구의 임상적용시 문제)

  • 최한철
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2003.10a
    • /
    • pp.15-15
    • /
    • 2003
  • 치과재료에 사용되는 금속재료는 주로 스테인리스강, 타이타늄, Ni-Ti, Co-Cr등과 같은 특수합금이 주로 사용되고 있다. 이들 재료는 치과 보철물과 교정재료 및 충전재료로 주로 사용되고 있으며 그 외 치과에서 사용되는 기기나 기구에도 많이 활용되고 있다. 특히 치과 보철물을 사용하여 치료를 원하는 환자가 최근에 급격히 증가하면서 임플란트 고정체와 나사 등을 이용한 치료법의 연구와 개발이 필요하게 되어 세계적으로 연구와 투자가 활발히 진행되고 있다. 그러나 재료의 설계나 합금의 설계 및 제품의 설계상의 문제로 인하여 생체조직과 결합하는데 많은 문제점이 임상적으로 발생되고 있다. 즉 임플란트 표면의 생체적합성부여, 고정체와의 결합시 파절이나 풀림현상, 골에 고정체로 사용하는 나사의 강도와 내마모성문제 등이 개선되어야 할 문제점으로 남아있다. 또한 총의치에 사용되는 자석 어태치먼트의erosion-corrosion문제, 교정선의 탄성 과 마모저항문제 등은 앞으로 계속적인 연구를 행하여야할 과제로 남아있다. 또한 국소의치에서 사용되는 frame은 정밀주조법을 통하여 제조하며 주조상의 결함 등으로 인한 클라스프의 파절 문제점이 발생되고 있다. 따라서 본 연구에서는 치과재료로 사용되는 임플란트 고정체, 나사, 교정용 선등의 문제점을 고찰하고, 지금까지 이루어진 연구를 중심으로 최적의 개선 조건을 찾고자하였다. 최근첨단소재 및 금속재료를 사용하여 치과재료 합금을 설계할 수 있는 연구가 활발히 진행된다면 수입에 의존하고 있는 고가의 치과재료를 값이 싼 고성능의 제품으로 대체할 수 있는 효과가 클 것으로 생각된다.>$\rho$$\sub$0/=1.8 %. As t$\sub$Co/ increases, a transition from the regime of co-existence of superparamagnetic and ferromagnetic behaviors to ferromagnetic behavior was observed. Tunneling barrier called "decay length for tunneling" for the films having the thickness of Co layer from 1.4 to 1.6 nm was measured to be ranged from 0.004 to 0.021 ${\AA}$$\^$-1/.문에 기업간 관계를 연구하는 측면에서는 탐험적 연구성격이 강하다. 더 나아가 본 산업의 주된 연구가 질적이고 기업내부만을 연구했던 것에 비교하면 시초적이라고 할 수 있다. 또한 관계마케팅, CRM 등의 이론적 배경이 되고 있는 신뢰와 결속의 중요성이 재확인하는 결과도 의의라고 할 수 있다. 그리고 신뢰는 양사 간의 상호관계에서 조성될 수 있는 특성을 가진 반면, 결속은 계약관계 초기단계에서 성문화하고 규정화 할 수 있는 변수의 성격이 강하다고 할 수가 있다. 본 연구는 복잡한 기업간 관계를 지나치게 협력적 측면에서만 규명했기 때문에 많은 측면을 간과할 가능성이 있다. 또한 방법론적으로 일방향의 시각만을 고려했고, 횡단적 조사를 통하고 국내의 한 서비스제공업체와 관련이 있는 컨텐츠 공급파트너

  • PDF

Water Governance and Basic Water Law (물거버넌스와 물관리기본법)

  • Lee, Seung-Ho;Kim, Sung
    • Proceedings of the Korea Water Resources Association Conference
    • /
    • 2009.05a
    • /
    • pp.385-389
    • /
    • 2009
  • 본 연구의 목적은 물거버넌스 개념과 1997년, 2006년 물관리기본법안 분석을 통해 한국의 새로운 물관리 체제를 모색하는 것이다. 물거버넌스는 물관리정책과 계획의 수립, 시행, 평가에 있어 정부뿐만 아니라 일반 기업, 시민, 환경단체, 전문가 등 여러 이해당사자를 참여시키는 것을 핵심으로 한다. 거버넌스란 기존의 정부 주도의 정책 계획, 수립, 시행이 아닌 비정부 조직과의 타협, 협의, 논의를 통한 양방향 정책결정 과정을 뜻한다. 따라서 물거버넌스의 가장 중요한 원칙은 다양한 이해당사자 참여를 통한 정책결정의 복수화 과정이다. 한국의 물거버넌스를 시행하기 위해 가장 필요한 요건은 이해당사자 참여를 우선 중앙, 지방정부에서 그 필요성을 인식하고 법, 제도 등을 통해 제도화하는 것이다. 환경부 주도로 입안된 1997년 물관리기본법안은 물관리일원화, 적정사용, 유역관리, 비용부담, 균형배분의 5원칙을, 2006년 물관리기본법안은 물관리일원화 대신 통합물관리, 적정사용 대신 수요관리를 삽입하여 5원칙을 제시하였지만 이해당사자 참여는 원칙에 포함시키지 않았다. 이해당사자 참여 원칙의 제도화가 없이는 위의 두 법안이 제시한 원칙의 적용과 시행이 어려움에 봉착할 가능성이 높다. 왜냐하면 다른 원칙은 다양한 이해당사자 참여를 통한 사회적 합의 없이는 시행이 쉽지 않은 정치적으로 민감한 사항들이기 때문이다. 예를 들어 물의 균형배분 원칙 관련, 만약 상류와 하류 주민 간의 합의가 없이 어느 한 이해당사자의 일방적 행위가 있을 경우 큰 갈등을 유발할 수 있다. 물거버넌스을 실행하기 위해 중앙에 필요한 조직은 물이용 관련 물분쟁 발생 시 이를 조정하고 국가물관리계획을 수립하며 물관리 문제 전반을 총괄하는 조직이다. 1997년, 2006년 기본법안은 국가물관리위원회 설치를 제시하였고 2006년 기본법안에서 보다 구체적으로 위상, 운영, 역할 등에 대해 언급하였다. 하지만 국가물관리위원회는 물관련 중앙부처의 장, 지방행정조직의 장만을 포함하여 유역관리를 책임질 유역관리조직의 장에 대한 언급이 없다. 물거버넌스 실현을 위한 유역관리 시행이 바람직하기에 유역관리조직의 장도 국가물관리위원회에 참여하는 것이 바람직하다. 또한 두 기본법안 모두 국무총리실 산하에 위원회를 속하게 하였는데 이를 수정하여 대통령 직속기구로 규정하는 것이 국가물관리위원회가 정치, 행정, 재정적 압력에서 벗어나 일관성 있는 정책을 펼 수 있는 지름길이 될 것이다. 또한 지방의 물문제를 물관리계획에 적절히 반영하고 대응방안을 수립, 시행하기 위해서는 정부 관료뿐만 아니라 지방의회 의원, 환경단체, 기업, 시민, 전문가 등의 다양한 이해당사자가 참여하는 유역위원회가 필수적이다. 또한 유역 관련 물관리계획을 수립하고 사업을 추진하는 유역관리청도 필요하다. 유역위원회와 유역관리청은 유역 내 여러 이해당사자들이 물관리에 대해 다양한 의견을 개진하고 토론하며 합의점에 이르는 거버넌스를 수립할 수 있는 중요한 조직이다. 두 기본법안은 유역관리 원칙을 제시하긴 하였지만 유역관리 시행 관련 조직, 역할, 운영 등에 대해서는 언급이 없었다. 한국의 물관리는 소득, 문화 수준 향상으로 인한 양질의 물공급에 대한 요구, 시민사회의 발전, 지방분권화 등 정치, 경제, 사회의 변화를 수용하고 발전해 나가기 위해서는 여러 이해당사자의 참여와 합의에 바탕을 둔 물거버넌스 수립이 무엇보다 중요하다. 또한 이를 시행하기 위해서는 물관리기본법을 하루 속히 제정하여 제도적 기반을 갖춰 보다 효율적인 물관리시스템을 수립해야 한다.

  • PDF