• Journal of the Korean Society for Railway
• /
• v.19 no.1
• /
• pp.77-86
• /
• 2016

Before urban railway vehicles reach their design life-span, operating agencies should determine when to buy new vehicles. Previous LCC (Life Cycle Cost) studies were limited because they independently focused on existing vehicles based on costs that directly impacted only the operating agency without considering effects such as social costs and the reduction of maintenance costs. Thus, it is difficult to systematically determine when to buy new vehicles. This study investigated the operating and maintenance related costs, especially from additional expenses and social costs due to unexpected vehicle failures and safety accidents, and did an economic analysis of scenarios with different discount rates. Considering that the public is very concerned about safety after the Sewol ferry accident, additional costs, which include social costs, should be included in the analysis. This study shows that the economic priority of scenarios may change depending on whether those costs are included and on the discount rate. The results of this study can help in the decision-making process for the planning and buying of new trains.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.233-240
• /
• 2005

In this paper, AC electric vehicle propulsion system(Converter/Inverter) using high power semiconductor, IPM is proposed. 2-Parallel operation of two PWM converter is adopted for increasing capacity of system and the harmonic content is eliminated by the phase shaft between two PWM converters switching phase. VVVF inverter control is used a mixed control algorithm, where the vector control strategy at low speed region and slip-frequency control strategy at high speed region. The proposed propulsion system is verified by experimental results with a 1,350kW converter and 1,100kVA inverter with four 210kW traction motors.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.650-654
• /
• 2007

Induction motors are widely used as a source of driving force in electric vehicles and pulse width modulation (PWM) inverters are applied to their operation. The issue is that insulation of inverter-fed induction motors (IFMs) are more stressed than in line-powered motors by transient voltages. This paper dealt with experimental results on transient voltage produced by the PWM operation of an induction motor. The peak and the dv/dt of transient voltage depending on the length of power feeding cable and operating frequency were investigated. In the experiment, transient voltages up to 3.3PU of the rated-inverter voltage were recorded for the cable length of 50m. As the cable length is increased, the peak voltage appeared at the motor terminals increases. This phenomenon can be explained by the reflection and the transmission of travelling wave. Consequently, special care for the cable length between the motor and the inverter should be taken in the use of IFM to ensure the full life of insulation system.

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.136-138
• /
• 2007

본 논문에서는 전압강하 보상 기능을 갖는 직류 지하철 회생 인버터 시스템을 제안하였다. 직류 지하철 시스템의 정류기 사고 및 급전선의 단선사고로 인해 계통으로부터 원활한 전력을 공급받지 못하는 경우 전동차가 운행할 수 없다. 이러한 문제점을 해결하기 위해 직류 지하철 시스템과 병렬로 연결되어진 회생인버터에 전압강하 보상 기능을 추가 하였다. 본 논문에서 제안하는 전력변환기는 양방향으로 전력 제어가 가능하여 하나의 전력변환기기로 3가지의 기능을 수행한다. 시뮬레이션과 실험을 통해서 제안된 시스템의 타당성을 확인한다.

• Journal of the Korean Society for Railway
• /
• v.11 no.4
• /
• pp.398-403
• /
• 2008

The propulsion for locomotive application has changed from the DC motor system to the induction motor system. Although the induction motor system has almost reached the stage of maturity, this system also needs to be changed to the PM motor system for the direct drive without using reduction gear. Thus, the IPMSM (Interior buried Permanent Magnet Synchronous Motor) has been adopted to meet the locomotive driving specification. Where the wheel is directly dirven by the traction motor. In this paper, the investigation on IPMSM satisfying driving specifications for the direct drive has been performed using the advanced FEM.