• Journal of the Korean Ceramic Society
• /
• v.30 no.9
• /
• pp.717-722
• /
• 1993

Effects of microstructures on the electrical properties of ZrO2 based ceramics were analyzed by modeling layer arrangements and mixed phase structures. Single layers and alternating multilayers were made from 3mol% and 8mol% Y2O3 doped ZrO2 powders, while mixed specimen was made by blending and compacting these raw powders. After sintering at 150$0^{\circ}C$ for 2hr in air, AC impedance characteristics were measured. Contributiion of bulk comonent to total resistivity and its temperature-dependence were larger in 8Y-ZrO2 single layer than in 3Y-ZrO2 single layer. The multilayered specimen connected in serial to electrodes showed partial characteristics of both 3Y-ZrO2 and 8Y-ZrO2 single layers. The multilayered specimen connected in parallel to electrodes and the mixed specimen exhibited characteristics mainly of 8Y-ZrO2 single layer. The multilayered specimen connected in parallel to electrodes revealed the highest electrical conductivity near the operating temperature of solid oxide fuel cell. However, it is expected that the mixed specimen is appropriate for the applications because of its relatively high electrical conductivity with high strength expected.

• Journal of the Korean Ceramic Society
• /
• v.35 no.12
• /
• pp.1294-1300
• /
• 1998

Yttria-stabilized zirconia ceramics with irregular grain shapes and curved grain boundaries was prepared by ceria doping. The amount of ceria doped into zirconia compacts by a dipping method were at range of 2 to 20 mol% Irregular grain shapes and curved grain boundaries were formed only inspecimens doped with more than 8mol% cerial. Ceria-doped specimens showed large grain size and low sintered density compared with pure yttria-stabilized zirconia which was due to the increase in the contents of stabilizer and cubic phase. The amount of doped ceria was larger on the surface than the inside regions and therefore mi-crostructure and phase on the surface were different from those in the inside regions. Transgranular frac-ture mode was observed ion ceria doped specimens due to irregular large grain sizes.

• Korean Journal of Materials Research
• /
• v.28 no.2
• /
• pp.82-88
• /
• 2018

Stable slurries of YSZ in aqueous suspension with added polymer dispersants, namely, poly-methacrylic acid ammonium salt (PMMA), poly-acrylic acid (PAA) and poly-acrylic-co-maleic acid (PAMA), were mixed with the monomolecular dispersants citric acid and oxalic acid. The dispersion properties of the suspension were investigated using PSA, viscosity, sedimentation, and FT-IR. The polymer dispersants and monomolecular dispersants were attached to the YSZ surface by the carboxylic group, as shown by the FTIR results. A stabilized aqueous suspension was obtained when the polymer dispersant and citric acid were mixed and compared to the use of citric acid alone as a dispersant agent. When the polymer dispersant and citric acid were mixed and milled through attrition milling, there was a smaller particle size compared to when the polymer dispersant alone was used as a dispersant agent. This study determined that the particle size of the mixed dispersant was affected by the properties of the monomolecular dispersant and that the stability of the suspension was affected by the polymer dispersant. However, when slurries of YSZ were mixed with oxalic acid, the particle bridging behavior was the result of the high degree of viscosity and the small sedimentation height.

• Journal of Power System Engineering
• /
• v.4 no.4
• /
• pp.48-53
• /
• 2000

This study was aimed at observing the influence of laser irradiation on a $ZrO_2-8%Y_2O_3$ ceramic coating layer fabricated by plasma spraying. The $ZrO_2-8%Y_2O_3$ ceramic powder was plasma sprayed onto SS400 carbon steel substrate and laser irradiated on the coating layer under various conditions of laser power and beam diameters. As to the as-sprayed specimen and laser-treated specimen, a hardness test and a microstructure analysis were performed. Hardness was measured by a microhardness tester; microstructure was observed by an optical microscope and a scanning electron microscope. The result was that the microstructure of the laser-irradiated coating layer was dense; porosities almost disappeared and hardness increased. It was also observed that microcracks occured in the laser-irradiated coating layer.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.2
• /
• pp.141-148
• /
• 2006

This study was carried out to analyze the microstructure characteristics of electrolyte membrane through XRD, SEM and AC impedance measurement for using in high temperature steam electrolysis(HTE). It was investigated that thermal stability and electric characteristics by sintering condition using dry and wet process, and confirmed growth of particle and density change by sintering temperature. The sintering temperature and behavior had an effect on the relative density of the ceramic and the average grain size. The more amount of dispersant in organic compound increase, the more the density increased. But the binder was shown opposite phenomenon. It was analyzed that electrolyte resistance and electrical characteristics using AC impedance. The electrical properties of YSZ grain boundary changed with the sintering temperature.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.1
• /
• pp.1-8
• /
• 2024

Phase stability of tetragonal crystals in yttria-stabilized zirconia ceramics is dependent on the content of yttria and the heat-treatment condition, related with mechanical properties. In this study, we fabricated the 1.5 mol% yttria-stabilized zirconia (1.5Y-YSZ) ceramics by cold isostatic pressing (CIP) and post-sintering at temperature range of 1200 to 1350℃ for 2 hours and investigated the sintered properties and microstructural evolution. Sintered and microstructural parameters, i.e, apparent density, grain size and phase composition of 1.5Y-YSZ ceramics were mainly dependent on the sintering temperature. Maximum sintered density of 99.4 % and average grain size of 200-300 nm could be obtained from the heat-treatment condition above sintering temperature at 1300℃ for 2 hours, possessing the superior mechanical hardness with 1200 Hv. However, phase stability of tetragonal grains in 1.5 YSZ ceramics is very low, inducing the phase transformation to monoclinic crystals on specimen surface during cooling after heat-treatment.

• Journal of the Korean Ceramic Society
• /
• v.36 no.8
• /
• pp.791-798
• /
• 1999

The preparation method of yttria-stabilized zirconia(YSZ) thin film for an anode support type solid oxide fuel cell(SOFC) by electrophoretic deposition(EPD) and dip-coating was studied. And the difference in both preparation method was investigated through basic understanding of processing parameters which may significantly affect weight microstruxcture and defect of film. In dip-coating the thickness of film increased with time until 30 s and then the weight of film decreased with time due to particle falling off from the coagulated film. In EPD although the weight of film increased with time and applied constant-current sagging of the film was observed when the applied current was less that 0.035 mA/$cm^2$ and more than 120 s. Since YSZ thin film by EPD on porous substrate was dense smooth and homogeneous it was expected to be suitable for the electrolyte of an anode support type SOFC.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.93-100
• /
• 1992

Sinterability, mechanical and electrical properties of yttria-stabilized zirconia(92 mole% $ZrO_{2}$+8 mole% $Y_{2}O_{3}$) doped with 0.5 mole% $SiO_{2}$ and $0{\sim}2.0 mole%{\;}Al_{2}O_{3}$ were studied as a function of $Al_{2}O_{3}$ addition. Sintered density increased with increasing $Al_{2}O_{3}$ addition up to 0.5 mole % but leveled off with further addition. Victors hardness is proportional to sintered density. The specimen with 0.5 mole% $Al_{2}O_{3}$ and 0.5 mole% $SiO_{2}$ exhibited the maximum electrical conductivity and revealed a maximum electromotive force for a given oxygen partial pressure. Experimental voltage curve of this oxygen sensor take on a sharper, more steplike transition at the stoichiometric A/F ratio than those of other commercial oxygen sensors.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.5
• /
• pp.592-598
• /
• 2011

Electrode of solid oxide fuel cell must have sufficient porosity to allow gas transport to the interface with electrolyte effectively but high porosity has a negative impact on structural stability in electrode support. Thus, the upper limit of porosity is based on consideration of mechanical strength of electrode. In this study, the effect of microstructure of Ni-YSZ anode supported SOFC on the mechanical and electrical property was investigated. LSCF composite cathode and 8YSZ electrolyte were used. The porosity of the anode was modified by the amount of graphite powder and added graphite contents were 24, 18, 12 vol%, respectively. The higher the porosity, the better the electrical performance, $P_{max}$. While the flexural strength decreased with increasing the amount of graphite. But the rate of increase in electrical performance and the rate of decrease in mechanical strength were not directly proportional to amount of graphite. The optimum graphite content incorporating both electrical and mechanical performance was 18 vol%.

• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.320-329
• /
• 1992

In 2Y-TZP powders calcined at temperature range of 80$0^{\circ}C$0 to 150$0^{\circ}C$, the effect of stabilization and the transformability of tetragonal phase on the tetragonal to monoclinic transformation have been investigated. The transformability of tetragonal phase in calcined powders shows maximum at the calcination temperature of 130$0^{\circ}C$. This result is explained by a combined effect of the increase of particle size and of constrained force among the particles with increasing the calcination temperature. The amount of transformed monoclinic phase with calcination temperature after quenching in liquid nitrogen, stress induction and isothermal aging at 25$0^{\circ}C$is also explained by the transformability of tetragonal phase determined by the sum of particle size effect and constraint effect.