• Journal of Convergence for Information Technology
• /
• v.9 no.12
• /
• pp.147-156
• /
• 2019

Numerical study was performed to investigate the convective heat transfer of Al₂O₃/water nanofluid flowing through the concentric double pipe counterflow heat exchangers. Hot fluid flowing through the inner pipe transfers its heat to cooling fluid flowing in the outer pipe. Effects of important parameters such as hot and cold volume flow rates, fluid type in the outer and inner pipes, and nanoparticles concentration on the heat transfer and flow characteristics are investigated. The results indicated that the heat transfer performance increases with increasing the hot and cold volume flow rates, as well as the particle concentrations. When both outer and inner pipes are nanofluids with 8% nanoparticle volume concentration, nanofluids showed up to 17% better heat transfer rate than basic fluids. Also, the average heat transfer coefficient of the base fluid for annulus-side improved by 31%. Approximately 20% enhancement in the heat exchanger effectiveness can be achieved with the addition of 8% alumina particles in base fluid. But, addition of nanoparticles to the base fluid enhanced friction factor by about 196%.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.642-647
• /
• 2001

This study represents numerical analysis on the thermal and fluid flow of the air layer in a solar collector. The boundary conditions was assumed that the top and bottom wall of the air layer have a heating and cooling surface. respectively. and this calculation model have a solid body with a cooling temperature of $20^{\circ}C$. As the results of simulations. the magnitudes of the velocity vectors and isotherms are increased proportionally to the tilt angles. As the tilt angle is increased. the mean Nusselt numbers are increased and the maximum value of the mean Nusselt number was appeared at tilt angle ${\theta}=75^{\circ}$.

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1062-1068
• /
• 1999

The flexural strength distribution of alumina ceramics was observed using ball-on-3 ball test after thermal shock into the distilled water of 25$^{\circ}C$ Crack distribution was also observed by dye-penetration after thermal shock test. Fracture probability of alumina ceramics by ball-on-3 ball test was studied and compared with that by 3-point bending test. The crack distance from the center of thespecimen showed the stronger effect on the flexural strength by ball-on-3 ball test than the crack density.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.67-72
• /
• 1996

수격현상(Waterhammer)으로 인한 과도압력하중은 월성원자력발전소 비상노심냉각계통 (Emergency Core Cooling System : ECCS) 설계의 주요 고려사항이다. 비상노심냉각계통은 특수안전계통으로서 냉각재상실사고(Loss of Coolant Accident : LOCA)후 일차열수송계통을 다시 채워주고 핵연료 손상을 막기위해 노심으로부터 잔열 및 붕괴열을 제거한다. 일차열수송계통으로의 비상냉각수 주입은 고압주입, 중압주입, 저압주입 3 단계로 주입된다. 과도압력이 발생될 것으로 예상되는 고압주입과 중압주입에 대한 6가지 사례들이 ECCS의 배관과 지지대 설계를 위해 고려되었다. 모든 사례에 대한 비상노심냉각계통의 과도압력 현상은 PTRAN 코드에 의해 해석 되었고 해석된 최고과도압력은 설계압력보다 작음을 알게 되었다. 모든 사례의 최고압력과 최고차압은 비상노심냉각계통 배관 및 지지대 설계를 위한 응력해석 자료로서 사용될 것이다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.362-367
• /
• 1996

CANDU-6형 원자력발전소인 월성 2,3,4호기 비상급수계통의 성능을 평가하기 위하여 설계기능 수행과 관련된 변수로서 격납건물내 집수조(sump) 온도와 열수송계통으로 주입되는 냉각재온도를 사용한 분석을 수행하였다. 이 온도들은 NTU(Number of Transfer Unit)방법을 이용한 비상노심 냉각계통 열교환기의 열전달속도와 열전달계수의 해석을 열평형관계식과 함께 조합한 프로그램을 사용하여 계산하였다. 또한 증기발생기 급수량과 추후 수조에 공급되는 보충수에 대한 설계요건을 검토하였다. 이러한 변수와 설계요건은 비상급수계통이 발전소 정상 열제거기능 상실후 노심의 붕괴열제거에 유효한 열침원으로서의 기능을 수행함을 보여 주었다. 또 격납건물의 건전성 유지와 관련된 집수조내 최고온도가 허용치 이하로 유지되었다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.166-173
• /
• 2012

This study is about comparison of thermal and flow characteristics on the wind & radiant heat shield with STS mesh type screen for offshore. Numerical analysis was conducted to find transmission coefficient in the mesh and then analyse the flow characteristics about wind & radiant heat shield. The experiment method of solar radiation has been used as thermal radiation source to get the performance of radiant heat shield measurement. The sensor radiation device has been used to measure the reduction of solar radiation with various size of cells and at a distance of 0.5m and 1m from the cold face of the wind & radiant heat shield.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.391-396
• /
• 1996

내부부수로, 벽면부수로, 모서리부수로를 포함하는 가압경수로형 원자로의 핵연료집합체를 모의하는 3$\times$3 봉다발을 모델로 수치해석을 통해 봉다발 주변의 유동특성을 알아보고 각 봉에서의 원주방향 위치에 따른 국소열전달 특성에 관해 고찰하였다. 봉다발에서 열전달계수의 분포는 벽면영향으로 인한 각 부수로에서의 유속분포와 밀접한 관계가 있으며 내부부수로에 인접한 봉에서 가장 높았고, 그 다음이 벽면부수로, 모서리부수로에 인접한 봉에서는 가장 작게 나타났다. 현재 핵연료의 열수력 설계시에 적용하고 있는 부수고 내의 모든 열수력학적 변수가 일정하다고 가정하는 부수로 해석방법은 봉다발내의 실제 열전달 현상과는 상당한 차이가 있음을 보여주었다.

• Journal of the KSME
• /
• v.31 no.9
• /
• pp.812-819
• /
• 1991

고분자 폐기물을 처리하는 방법은 크게 재이용, 소각, 매립 등으로 나눌 수 있으나 재이용이나 매립 방법은 폐기물의 급속한 증가를 감당하기에 한계가 있다. 소각은 폐기물의 감량화와 폐열 회수의 이중 효과를 얻을 수 있는 가장 일반적이고 손쉬운 방법이긴 하지만 폐고무나 폐합성 수지와 같은 고분자폐기물을 직접 소각할 때에는 많은 유해가스, 분진과 매연이 발생하는 어려 움이 따른다. 건류소각 방식은 이러한 직접 소각의 단점을 보완해 주는 것으로 최근 각광을 받고 있으나 안전성, 유지관리 및 시설비 등의 면에서 뿐만 아니라 기술적인 면에서도 아직 많은 연 구가 요구되고 있다. 열분해 또는 건류 가스화에 관한 연구는 석탄에 대하여 활발하게 이루어져 왔으며 1960년대에는 심각한 환경오염을 겪으면서 폐기물 처리에 대한 응용이 시작되었다. 1970년대부터 미국에서는 EPA(environmental protection agency)의 주도로 도시쓰레기에서 가스, 기름 등을 회수하는 기술개발을 강력히 추진하였으며 일본에서도 통상산업성 산하 공업기술원의 도시쓰레기 열분해 처리 기술 개발을 시작으로 2차공해 감소를 선결 과제로 한 여러 가지 프로 세스를 개발해 왔다. 국내에서는 최근에들어 연구가 비교적 활발하게 이루어 지고 있다. 특히 동력자원부 주관의 대체에너지 사업의 일환으로 추진중인 폐기물의 에너지화 이용에 관한 연구 중에서도 열분해나 건류 가스화에 관련된 연구가 많은 비중을 차지하고 있다.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.12
• /
• pp.1371-1380
• /
• 2007

Study on the instability of waste plastic's thermal pyrolysis oil was carried out for the purpose of improving its quality. The reaction of pyrolysis oil with ozone changed double bonds into aldehydes and ketone, estimated that HDPE pyrolysis oil contained $\sim45$ wt% 1-alkene type olefins, and PP pyrolysis oil did $\sim73$ wt% olefins, which consisted of $\sim47$ wt% secondary and $\sim20$ wt% primary alkenes. The dark brown color and odor of pyrolysis oil were improved by eliminating double bonds, indicated that they were directly related to unsaturated hydrocarbons. Container test showed that metal can affected oil quality worse than the brown glass bottle. Antioxidant added into pyrolysis oil was consumed up to 90% within $2\sim3$ days and the wt. composition of unsaturated hydrocarbons in pyrolysis oil was not changed within 50 days, inferring that instability of pyrolysis oil due to unsaturated bonds can be stabilized by antioxidants. Adsorption test on silica gel, activated carbon and alumina to remove precipitates in oil produced a good result, but not enough to remove moisture. However, cheap anhydrous sodium carbonate showed the best removal efficiency of moisture as well as precipitates in oil. Therefore the pyrolysis oil quality improvement was accomplished by applying anhydrous $Na_2CO_3$ into the production plant.

• Analytical Science and Technology
• /
• v.31 no.2
• /
• pp.78-87
• /
• 2018

Asian lacquer has been used as an adhesive and coating material in Asian countries, such as China, Japan, and Korea, and other southeast Asian countries. In this study, the changes in the chemical structure of lacquer with drying was analyzed using pyrolysis/GC/MS (which is useful in analyzing polymeric material) to understand its drying procedures. Upon increasing temperature, the dried lacquer was fully pyrolyzed above the pyrolysis temperature of $500^{\circ}C$. The repeatability was good at the pyrolysis temperature of $500^{\circ}C$ (rsd = 2.6-22.3 %); however, there were differences in the pyrogram patterns when the difference in sample quantity was large. The characteristic peaks of Asian lacquer components, such as those corresponding to 1,2-benzenediol and 3-methyl-1,2-benzenediol, were detected and the compound of each peak was assigned according to the mass library. As the lacquer dried, the composition of pyrolysis products with urushiol derivatives bearing 3 C=C bonds was severely reduced compared with the ones with no C=C bonds, indicating that the polymerization is related to C=C bonds. These results can be applied to confirm the presence of lacquer in excavated relics and to monitor the changes in the composition of raw lacquer with drying.