• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.48-53
• /
• 1995

The structure, magnetic properties and magnetoresistance phenorrena of Ag-Co nano-granular alloy films prepared by a thermal co-evaporation were studied. Supersaturated fee Ag-Co solid solution and fee Co clusters coexisted in the as-deposited state. As Co content increases from 20 to 55 at.% Co, the grain size of the Ag matrix decreases from 147 to $67{\AA}$, and the Co solubility in the Ag matrix increases from 2.5 to 6.7%. Ag-Co alloy films having composition below 25 at.% Co showed mainly superparamagnetic behavior and above that composition, they showed both paramagnetic and ferromagnetic l::ehavior in the as-deposited state. The maximum magnetoresistance of 19% at R. T. and 10 kOe was obtained in the as-deposited 30 at.% Co alloy film. Heat treatment did not improve the MR ratio tecause most of the Co was already precipitated in the as-deposited state.

• Corrosion Science and Technology
• /
• v.19 no.3
• /
• pp.122-130
• /
• 2020

In this study, a corrosion failure analysis of a heat transport pipe was conducted, as the result of a pinhole leak. Interestingly, the corrosion damage occurred externally in the pipeline, resulting in severe thickness reduction near the seam line. Also, while a stable magnetite protective film formed on the inner surface, the manganese oxide formation occurred only on the outer surface. The interior and exterior of the pipe were composed of ferrite and pearlite. The large manganese sulfide and alumina inclusions were found near the seam line. In addition, the manganese sulfide inclusions resulted in grooving corrosion, which progressed in the seam line leading to the reduction in the thickness, followed by the exposure of the alumina in the matrix to the outer surface. To note, the corrosion was accelerated by pits generated from the boundaries separating the inclusions from the matrix, which resulted in pinhole leaks and water loss.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.12
• /
• pp.1159-1169
• /
• 2013

EQM Model Digital transponder applying the Korean's own designing and manufacturing technology has gone through a series of trials and errors during the development. In particular, lack of thermal designs expedience for the vacuum causes variety of errors in designing, assembling transponder and setting up the test at the first thermal vacuum test (TVAC). Since the first TVAC test could not accomplished its aims successfully, so the second TVAC should be performed as make up test with revised Digital transponder. In this paper, the defects that identified in the first TVAC are analyzed and applied solutions and its results at the second TVAC are presented. Using the lessons from the first and second TVAC, we will be able to make more reliable digital transponders in the next phase of project. In addition it also be useful as a reference when we design another satellite payloads.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.8
• /
• pp.857-864
• /
• 2012

A linear stability analysis of a diffusion flame with radiation heat loss is performed to identify linearly unstable conditions for the Damk$\ddot{o}$hler number and radiation intensity. We adopt a counterflow diffusion flame with unity Lewis number as a model. Near the kinetic limit extinction regime, the growth rates of disturbances always have real eigenvalues, and a neutral stability condition perfectly falls into the quasi-steady extinction. However, near the radiative limit extinction regime, the eigenvalues are complex, which implies pulsating instability. A stable limit cycle occurs when the temperatures of the pulsating flame exceed the maximum temperature of the steady-state flame with real positive eigenvalues. If the instantaneous temperature of the pulsating flame is below the maximum temperature, the flame cannot recover and goes to extinction. The neutral stability curve of the radiation-induced instability is plotted over a broad range of radiation intensities.

• Fire Science and Engineering
• /
• v.19 no.3 s.59
• /
• pp.70-75
• /
• 2005

The heat of combustion of polymer materials is an important fire characteristics, which can be used with other fire parameter to predict the potential fire hazard in the polymer handling process. The aim of this study is to predict the heat of combustion for polymers which used in the building interior materials. By using the literature data and multiple regression, the new equation for predicting the heat of combustion of polymers is proposed. The A.A.p.E.(average absolute percent error) and the A.A.D.(average absolute deviation) of the reported and the calculated heat of combustion by means of the oxygen consumption calorimeter and the stoichiometric coefficient were 4.46 and 1.09, and the correlation coefficient was 0.972. The values calculated by the proposed equations were in good agreement with the literature data. Therefore, it is expected that this proposed equations will support the use of the research for other polymer materials.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.3
• /
• pp.107-113
• /
• 2005

A calorimeter of 2-ton thrust level rocket engine chamber has been developed to measure the wall heat flux. The liner of the chamber is made of copper-chromium alloy to maximize the heat transfer performance and structural strength. 1-D design code based on empirical correlations has been used for the prediction of the global thermal characteristics while 3-D CFD has been applied for the verification of local cooling performance. The predicted average wall heat flux at the throat is 43 $MW/m^{2}$ for the combustion chamber pressure of 53 bar. The chamber structure is confirmed to be safe at the pressure of 150 bar through 2-D stress analysis and measurement of the strain of the test species. Finally, the test of pressurizing the calorimeter chamber has been performed with water at the pressure of 150 bar in room temperature environment. No thermal damage has been detected after the hot-fire test in the test nozzle of same cooling performance with the developed calorimeter though the measured throat heat flux is higher than the design value by 10%.

• Korean Journal of Remote Sensing
• /
• v.39 no.5_4
• /
• pp.1085-1095
• /
• 2023

Time-series data generated from satellite data are crucial resources for change detection and monitoring across various fields. Existing research in time-series data generation primarily relies on single-image analysis to maintain data uniformity, with ongoing efforts to enhance spatial and temporal resolutions by utilizing diverse image sources. Despite the emphasized significance of time-series data, there is a notable absence of automated data collection and preprocessing for research purposes. In this paper, to address this limitation, we propose a system that automates the collection of satellite information in user-specified areas to generate time-series data. This research aims to collect data from various satellite sources in a specific region and convert them into time-series data, developing an automatic satellite image collection system for this purpose. By utilizing this system, users can collect and extract data for their specific regions of interest, making the data immediately usable. Experimental results have shown the feasibility of automatically acquiring freely available Landsat and Sentinel images from the web and incorporating manually inputted high-resolution satellite images. Comparisons between automatically collected and edited images based on high-resolution satellite data demonstrated minimal discrepancies, with no significant errors in the generated output.

• Journal of Biomedical Engineering Research
• /
• v.33 no.1
• /
• pp.32-38
• /
• 2012

Recently, several ultrasound imaging techniques for tissue characterization have been developed. Among them, ultrasound elastography is regarded as the most promising modality and has been rapidly developed. One of ultrasound elastography techniques is shear modulus imaging. Normal and cancerous tissues show big difference of shear moduli and they have good image contrast. However shear wave elastography requires more complicated hardware and more computations for image reconstruction algorithm. Therefore new efficient techniques are being developed. In this paper, we have developed a very flexible ultrasound system for elastography experiments. The developed system has capabilities to acquire ultrasound RF data of all channels and generate arbitrary ultrasound pulse sequences. It has a huge amount of memories for RF data acquisition and a simple and flexible pulse generator. We have verified the performance of the system showing conventional B-mode images and preliminary results of elastography. The developed system will be used to verify our own reconstruction algorithm and to develop more efficient elastography techniques.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.3
• /
• pp.181-188
• /
• 2003

In this paper, we introduce a magnetic noise shielding method to reduce the noise effects in permanent magnet based MRI systems. Through FEM electromagnetic analyses, we have shown that the magnetic noise component parallel to the main magnetic field is the major component that makes various artifacts in the images obtained with a permanent magnet based MRI. Based on the FEM analyses, we have developed an active magnetic noise shielding system composed of a magnetic field sensor, compensation coils, and a coil driving system. The shielding system has shown a noise rejection ratio of about 30dB at the frequency below several Hz. We have experimentally verified that the shielding system greatly improves the image quality in a 0.3 Tesla MRI system.

• Progress in Medical Physics
• /
• v.5 no.1
• /
• pp.13-24
• /
• 1994

In the conventional thermograph systems, expensive infrared lens systems are usually used for accomodating infrared beams to high speed optical scanners. In this study, a cheap focussing mirror with a two dimensional scanner are used for the development of medical infrared thermograph system in which high speed imaging is not critically required. The infrared thermograph system can be used for two dimensional imaging of human skin temperature by measuring the amount of infrared lights radiating from it. It has been experimentally proven that the accuracy of temperature measurements using the developed system is under 0.1$^{\circ}C$ with image matrix size of 256${\times}$240, and imaging time of 4 seconds.