• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.405-409
• /
• 2010

금속분말을 청정 에너지원으로 이용하기 위해 금속분말 소형 연소기의 구현이 필요하다. 이를 위한 선행연구로 연료 공급 시스템인 핀틀인젝터형(pintle injector type) 금속분말 공급장치의 중요 성능인 분사량을 실험적으로 측정하였다. 분사량 측정 시험에 앞서 간단한 금속분말 공급 시험으로 확인된 문제점을 장치의 변경을 통해 해결하였다. 측정 시험의 결과, 연료 공급 장치에 이송 가스 압력이 상승함에 따라 많은 질유량의 금속분말이 분사되었고 압력에 따른 정량적 분사량을 확인하였다. 이송 가스와 금속분말의 혼합 성능을 개선하여 균일한 분사를 하고자 이송 가스를 25 Hz로 가진 하여 공급하였고 가진이 없는 경우의 실험결과와 비교하였다.

• Resources Recycling
• /
• v.14 no.1
• /
• pp.39-46
• /
• 2005

A solid-state high power torch with inter-electrode insert (IEI) was developed to treat solid waste (for example, incinerated ash), and it's operation characteristics were obtained in the plasma facility test for waste treatment. According to torch test from this study, at the non-transferred mode voltage is increased by gas volume proportionally, and at the transferred mode it is not affected to voltage change. Especially arc voltage is sustained stable at the range of 10% of total Fe in slag. In addition, Electrical conductivity is 0.05~0.25${\Omega}^{-1}cm^{-1}$, torch efficiency is 75~85% and Erosion rate is 2${\times}10^{-6}~6{\times}10^{-6}$ kg/s.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.92.2-92.2
• /
• 2017

스퍼터링은 이온화된 불활성 기체가 음의 전압이 인가된 타겟에 충돌하여 운동량 전달에 의해 타겟 물질을 떼어내어 기판에 박막을 형성하는 진공증착 기술의 하나이다. 스퍼터링은 초기에 이극 또는 삼극 스퍼터링이 사용되다가 1970년대에 마그네트론 스퍼터링이 등장하면서 고속화 및 박막의 특성향상이 이루어졌으며 현재 스퍼터링 기술의 표준으로 자리를 잡았다. 마그네트론 스퍼터링은 그러나 타겟 효율이 30%내외로 낮고 여전히 다른 증착 기술에 비해 증발율이 낮다는 단점이 지적되고 있으며 이를 극복하기 위한 많은 연구가 진행되어 왔다. 증발율을 향상시키고 타겟 효율을 향상시킬 수 있는 방안의 하나로 HC-GFS(Hollow Cathode - Gas Flow Sputtering) 소스가 연구되어 왔다. GFS란 증기가 발생하는 부분과 증착이 이루어지는 부분의 진공도를 변화시켜 압력차에 의해 증기가 이송되어 증착되는 기술을 의미하며 HC-GFS는 타겟과 타겟 사이에 할로 방전을 발생시켜 이때 발생된 플라즈마로 타겟의 물질을 스퍼터링하고 스퍼터링된 입자를 압력차로 이송하여 기판에 증착하는 기술이다. HC-GSF 소스는 증발율이 향상되고 타겟 효율이 높다는 점에서 많은 관심을 가졌으나 아직까지 상용화 실적은 미미한 상황이다. 본 연구에서는 HC-GFS 소스를 제작하고 그 특성을 평가하였으며 금속을 증착하여 상용 증발원으로써의 가능성을 검토하고자 하였다.

• Journal of Animal Environmental Science
• /
• v.14 no.1
• /
• pp.47-52
• /
• 2008

Broken eggs not only cause the economic loss in the egg producing industry, but also may not be good for the consumer's health. In order to identify the causes of eggshell breakage in laying hen houses, analyses on the status of eggshell breakage in the step of egg conveyer system of the laying hen house were conducted. The survey of eggshell breakage rate was implemented by four different stages egg conveying system. In the results, the breakage rate showed 4.7% in the egg collection belt, 2.5% in the egg elevator, 1.7% in the egg grading system and 0.9% in the egg conveyor belt. In particular, to Hy-line Brown variety, as the hens' raising week old increased, the breakage rate of eggshell increased while the strength of eggshell decreased. In the regression analysis between the breakage rate of eggshell and the strength of eggshell, the coefficient of determination ($R^2$) by the test of significance was computed as 0.7, therefore the changes of the strength of eggshell affects the breakage rate of eggshell. However, between the strength of eggshell and thickness of egg shell, and between the strength of eggshell and strain of eggshell, there was no significant difference detected in the regression analysis.

• Journal of Animal Environmental Science
• /
• v.15 no.3
• /
• pp.241-250
• /
• 2009

This study was conducted to develop an prototype automatic feeder (AF) for growing-finishing pigs. The main components of AF were a feed storage hopper, a feeding motor, a feed agitator, a control box and a programmable IC, which were controlled by a personal computer. The powder type feed transfer rate of AF was average $9.83{\pm}0.4\;g\;s^{-1}$. In feeding test, growing pigs (Landrace) of about 43 kg live weight were used in the study, and was fed over a 6 weeks in pens with solid concrete floors. For feeding trials with AF, the operation time of the feeding motor was set to 2, 3, 4, 5, and 6 seconds per feeding. Pigs frequently used AF from 05:00 to 11:00 and from 11:00 to 17:00 without relationship to the operation time of the feeding motor. The AF operation time of the feeding motor to minimize feed loss was between 2 and 4 seconds. Pigs fed with AF had same or slightly higher average daily gam (0.8~0.9 kg) than that with a commercial feeder, and average daily feed intake (2.76~2.93 kg) and feed conversion ratio (3.10~3.66) of pigs fed with AF were same or lower than those with the commercial feeder except the operation time of the feeding motor set to 6 seconds. As a result, AF would help to use and improve the productivity of growing-finishing pigs.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.5 no.2
• /
• pp.63-67
• /
• 1972

Preliminary creel-holding test of live anchovies which are to be used as bait for the skipjact fishery, was conducted on the fish caught by set net and lift net. They were held in the creels constructed with bamboo frame and minnow netting, during the period of Oct. 24-Nov. 28 in 1972. If was found that the survival rate of the creel-held anchovies varied by the size of fish, the towed distance and speed of fish-carrying creel in which the fish were accomodated after catchi. 1. The survival rate of the medium size anchovies, 7.8-9.6cm in length and 4.6-4.8 g in weight, was $70-92\%$ during the holding period of 20-35 days. Whereas, only $16\%$ of juvenile anchovies, 5.3cm in length and 1.0 g in weight, were survived for 19 hours after catch. 2. During the time of transport, the farther and faster the creel containing fish were towed, the less fish were survived in the subsequent holding period. 3. Though both the set net and lift net could be fairly used to catch live anchovy, no decision between these two gears could be made in this experiment to determine the superiorness for the subsequent survival rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.7
• /
• pp.3275-3284
• /
• 2012

This study analyzed a 3D hydrodynamic advection diffusion using the EFDC model (Environmental Fluid Dynamics Code) in the agriculture lake to prevent stratification when we install a water circulator. EFDC model was predicted the range of the water circulator and various operational parameters ware derived for minimize the impact of the internal lake. Through EFDC simulation, water circulation is started overall circulation after 30days and a lake overall circulation showed that it was possible operated the water circulator after about 100days. Also, advection diffusion concentration was low in a lake when water circulator operate intermittent condition than continuous condition. And the entire circulation was stable in this condition. The S/B (Surface/Bottom) ratio can reduce the impact of lake as the surface water mixing a lot of. When the same condition (S/B ratio(3:1)), Case 8 (50days operation: 50days stop) of condition were able to minimize the impact of lake.

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.351-357
• /
• 2019

This research was performed to propose domestic standard for design and management of flexible hose by analyzing chlorine leak caused by breakage of the hose in Ulsan, 2018. The leak had multiple causes but this paper focuses on analyzing the cause of breakage of flexible hose, the direct cause. According to the analysis, flexible hose that the company of the accident used for chlorine transfer was inappropriate in several aspects including material and wall thickness. And even pressure test had been conducted below operating pressure. Upon investigation on five companies that handle chlorine in Ulsan, four companies were using inappropriate flexible hose for chlorine transfer. Since there is no domestic standard for the design of flexible hose for chlorine transfer at present, it is hard to examine its design adequacy. Design standard of flexible hose used in chlorine transfer that is applicable domestically is proposed based on this research. It will contribute to the reduction in risk of breakage of the hose if the proposed standard could be applied in design and examination of flexible hose.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.588-593
• /
• 2006

자연하천은 일반적으로 만곡수로나 사행수로 형태를 보이고 있으며, 직선수로에서와 달리 원심력에 기인한 이차류 영향을 받게 된다. 이차류에 의해서 수면에서는 만곡부 바깥쪽으로, 하상에서는 만곡부 안쪽으로의 흐름특성을 보이게 된다. 만곡부 안쪽으로 가해지는 하상 전단응력에 기인하여 하상에서의 입자가 만곡부 안쪽으로 이송되며, 결과적으로 만곡부 안쪽에는 점사주가, 바깥쪽에는 소(pool)가 생성된다. 또한 지형경사의 생성으로 입자에 가해지는 중력효과도 변화된다. 따라서 이와 같은 자연하천의 흐름과 하상변동을 수치모의 하기 위해서는 만곡부 이차류 특성을 고려한 모형이 필요하다. 본 연구에서는 수심 적분된 흐름방정식과 하상토 보존방정식 (Exner equation)을 이용한 하상변동을 위한 비연계 수치모형을 위해서 하상토 보존방정식의 유한요소 알고리즘을 개발하였다. 하상토 보존방정식은 흐름 특성에 따른 평형 유사량의 공간변화율을 이용하여 일정 기간 동안의 하상 변화량을 계산한다. 이 때 이차류에 의한 하상 전단응력의 편각 및 지형경사 변화에 따른 실제 입자의 이송방향을 보정하여 평형 유사량이 계산된다. 이러한 보정식을 적용시키기 위해서는 유속성분의 공간변화량 및 지형경사의 공간성분이 필요하다. 유한요소법은 연속성 변수를 이산화시켜 근사해를 구하는 수치기법의 일종이기 때문에, 요소망이 불규칙적으로 구성되었을 경우 임의의 절점에서 연속성을 지닌 변수의 공간변화율을 계산하는데 어려움이 있다. 따라서 본 연구에서는 평형 유사량 계산 시에 절점이 아닌 요소 내부에서 평형 유사량을 계산하는, 하상토 보존방정식의 새로운 유한요소 알고리즘을 개발하고, 새로운 알고리즘을 적용시킨 수치모형의 검증을 행하였다. 경계조건 알고리즘의 검증으로 위해서 Soni 등 (1980)이 행한 상류 유입 유사량에 따른 하상변동을 수치 모의하고 실험치와 비교하였으며, Sutmuller와 Glerum (1980)이 수행한 만곡수로에서의 하상변동을 모의하고 실험과 비교하였다. 새로운 알고리즘을 적용시킨 하상토 보존방정식의 유한요소 수치모형의 결과는 매우 안정적이며, 실험과 매우 유사한 결과를 얻을 수 있었다. 본 수치모델은 현재 균일한 입자의 하상토만을 고려하므로, 입자분급이나 하상 장갑화 현상 등은 무시한다.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.39-47
• /
• 2004

In mold machining, there are many concave machining regions where chatter and tool deflection occur since MRR(material removal rate) increases as curvature increases even though cutting speed and depth of cut are constant. Boolean operation between stock and tool model is widely used to compute MRR in NC milling simulation. In finish cutting, the side step is reduced to about 0.3mm and tool path length is sometimes over loom, so Boolean operation takes long computation time and includes much error if the resolution of stock and tool model is larger than the side step. In this paper, curvature of CL (cutter location) surface and side step of tool path is used to compute the feedrate for constant MRR machining. The data structure of CL surface is Z-map generated from NC tool path. The algorithm to get local curvature from discrete data was developed and applied to compute local curvature of CL surface. The side step of tool path was computed by point density map which includes cutter location point density at each grid element. The feedrate computed from curvature and side step is inserted to new tool path to regulate MRR. The resultants were applied to feedrate optimization system which generates new tool path with feedrate from NC codes for finish cutting. The system was applied to the machining of speaker and cellular phone mold. The finishing time was reduced to 12.6%, tool wear was reduced from 2mm to 1.1mm and chatter marks and over cut on corner were reduced, compared to the machining by constant feedrate. The machining time was shorter to 17% and surface quality and tool was also better than the conventional federate regulation using curvature of the tool path.