Journal of the Korea Academia-Industrial cooperation Society
/
v.16
no.10
/
pp.6977-6984
/
2015
It is faced with the necessity of multi roll forming process of the ball slide rail which is made by adding the separate manufacturing processes, piercing, bending, trimming, to the roll forming process of a continuous plastic deformation, to improve the quality. However, the vibration and noise of the press machine in this process leads to the quality degradation of slide rail manufactured in this process. In this study, the roll was designed considering the optimal strain rates by the roll forming program with finite element method. And to estimate the static stability of the multi process the Von-Mises stress and deformation on the press was calculated with a structural analysis program. Also, to avoid driving systems in the resonance region their natural frequencies in the 1st and 2nd mode were calculated through the modal analysis. To verify its dynamic stability improvement the magnitudes of noise and vibration in the existing and studied system were compared using a microphone and accelerometers. And the widths and surface roughnesses of the rails which had been produced in the existing and studied process were measured. Therefore, it is known that multi roll forming process is stable in the analytical and experimental study.
Park, Gi-Joon;Park, Jung-Jun;Kim, Sung-Wook;Lee, Jang-Hwa
Journal of the Korea Academia-Industrial cooperation Society
/
v.18
no.12
/
pp.697-704
/
2017
High-Performance Fiber-Reinforced Cement Composites (HPFRCC) has outstanding durability, and has attracted interest because of its ductility and development of strength, which allows a reduction of the self-weight of a structural member by substantially decreasing the cross section. Therefore, the present study aimed to improve the economic efficiency of HPFRCC by examining experimentally the flexural performance considering various characteristics of the steel fiber. To find an efficient fiber reinforcement method, the flexural performance was evaluated for different shapes, aspect ratios, and volume ratios of the steel fiber. Straight, hooked, and twisted fiber configurations were considered by adopting a fiber length longer than the usual 13 mm. The test results showed that HPFRCC reinforced by 19.5 nun-long straight fibers with a volume fraction of 1.5% shows better flexural performance than that reinforced by 13 mm-long straight fibers with a volume fraction of 2.0%. Consequently, HPFRCC with enhanced economic efficiency can be produced by adopting a reduced amount of steel fiber.
뇌성마비는 뇌 발달시기중 초기의 장애로 인하여 운동기능과 자세의 이상 등을 초래하는 질환으로 임상적으로 여러 유형으로 나누어진다. 뇌성마비 환자중에서 MRI 상 롤란도야의 이상소견을 보이는 경우 특이한 임상적 특징을 나타낸다고 보고되어있다. 본 논문에서는 이들을 대상으로 하여 뇌 단일광자컴퓨터촬영에서 나타나는 뇌혈류 이상 소견과 MRI 소견, 그리고 임상양상들을 비교해보고자 하였다. 임상적으로 뇌성마비로 진단된 80여명의 환자중 MRI상 롤란도야에 저산소성 뇌질환의 소견을 보인 7명을 대상으로 하였다. 이들에게 5-10mCi의 Tc-99m-ECD를 정맥주사후 뇌 단일광자컴퓨터촬영을 하였다. 뇌 단일광자컴퓨터촬영상에서는 특히 뇌피질, 선조체, 시상, 뇌간 및 소뇌의 혈류이상 소견을 분석하였고, 이를 MRI 소견 및 임상증상과 비교하였다. 모든 환자들은 만삭 또는 만삭에 가깝게 태어났고, 주산기 아사가 여섯명의 환자에서 있었다. 임상적으로는 긴장성 사지마비로 나타났다. Tc-99m ECD를 이용한 뇌 단일광자 컴퓨터촬영상 롤란도야의 혈류감소는 모두에서 확연하게 나타났다 MRI상에서 롤란도야의 이상소견은 5명에서는 확실하게 나타났고, 2명에서는 의심되었다. MRI상에서 이상소견을 보인 것보다 더 광범위한 부분에서 뇌단일광자컴퓨터촬영상 이상소견이 보였다. 결론적으로, 롤란도야에서 이상소견을 보인 환자는 임상적, 구조적, 그리고 기능적으로 특이한 소견을 보였다. Tc-99m-ECD를 이용한 뇌 단일광자컴퓨터촬영은 매우 민감하게 반영하였고, MRI보다 뇌의 더 광범위한 부위에서 이상소견을 보였다.
최근 WGS반응용 Pt 촉매의 성능 향상을 위한 다양한 담체 및 조촉매(Promotor) 개발에 대한 연구가 활발하게 진행되고 있다. 선행 연구결과, 입방(Cubic)구조를 가지는 $Ce_{0.8}Zr_{0.2}O_2$ 담체는 정방 입계(Tetragonal)구조를 가지는 $Ce_{0.2}Zr_{0.8}O_2$ 담체 또는 혼합산화물(Mixed oxide)구조를 가지는 $Ce_{0.5}Zr_{0.5}O_2$ 담체 보다 높은 활성과 안전성을 가진다. 이것은 촉매의 성능 향상이 Ce-$ZrO_2$의 결정구조에 의존한다는 것을 나타낸다. 따라서 WGS 반응에서 Ce/Zr 비에 따라 변화된 담체 특성이 Pt 촉매의 활성에 영향이 있을 것으로 예상되며 실험결과 1% Pt/$CeO_2$ 촉매가 가장 높은 활성을 나타내었다. 따라서 Pt/Ce-$ZrO_2$ 촉매의 성능 향상을 위해 Ce-$ZrO_2$ 담체에 조촉매인 Ni을 첨가하여 촉매적 활성을 비교하여 보았다. 촉매는 2%의 Pt과 15%의 Ni로 고정하였고 Ce/Zr 비를 제조변수로 하였다. 제조된 모든 담체는 공침법(Co-precipitation)을 사용하여 제조하였으며 $500^{\circ}C$에서 6시간 소성하였다. Pt 촉매는 함침법 (Incipient wetness impregnation)으로 담지 시켰다. 2% Pt/Ce-$ZrO_2$ 촉매와 2% Pt/15% Ni-Ce-$ZrO_2$ 촉매는 저온영역($200^{\circ}{\sim}320^{\circ}C$)에서 비슷한 CO 전환율을 나타내었으나 고온영역($360^{\circ}C{\sim}400^{\circ}C$)에서는 2% Pt/15% Ni-Ce-$ZrO_2$ 촉매가 더 높은 CO의 전환율을 나타내었다. 이것은 Ni의 영향으로 고온에서 부반응인 메탄화 반응(Methanation reaction)이 생긴 것으로 판단되어 메탄($CH_4$)의 선택도를 살펴본 결과 2% Pt/15% Ni-Ce-$ZrO_2$ 촉매가 고온영역($360^{\circ}{\sim}400^{\circ}C$)에서 급격하게 증가하는 것으로 나타나 메탄화 반응이 일어난 사실을 증명한다.
A normal and a waxy hull-less barley with similar ${\beta}-glucan$ contents were selected, and the effects of ${\beta}-glucans$ on rheological and pasting properties were investigated by using their flour extracts and isolated ${\beta}-glucan$ gum materials. ${\beta}-Glucans$ in the barley cultivars were extracted in a crude form with alkaline extraction, and the waxy hull-less barley produced more ${\beta}-glucan$ gum yield. The waxy barley also showed higher viscosities of water and alkaline flour extracts, compared to the normal barley. Both normal and waxy barley ${\beta}-glucan$ gums exhibited pseudoplastic flow behavior, and increasing ${\beta}-glucan$ concentration increased viscosity in a similar manner. The normal barley flour had a higher amylograph peak viscosity than did waxy barley flour. On the other hand, waxy barley flour with treatment of $HgCl_2$ demonstrated considerably higher increase in peak viscosity. Pasting characteristics of normal and waxy barley starches in the presence of ${\beta}-glucan$ gum solutions were tested using a rapid visco-analyzer (RVA). ${\beta}-Glucan$ gums increased the pasting viscosities of the barley starches, and the synergistic increase in viscosity appeared to be higher in the normal barley starch.
Kim, Suk-Shin;Chang, Kyu-Seob;Yoon, Han-Kyo;Lee, Sang-Kyu;Lee, Shin-Young
Korean Journal of Food Science and Technology
/
v.19
no.2
/
pp.81-88
/
1987
Rheological properties of rehydrated suspensions of two kinds of freeze dried Kochujang powders, processed at different freezing rates, were compared with raw Kochujang using Brookfield wide-gap rotational viscometer at $25^{\circ}C-60^{\circ}C$. Shear rates ranged from $0.1965\;sec^{-1}$ to $1.9650\;sec^{-1}$ and solid content ranged from 47% to 56%. Rehydrated suspensions of quickly frozen Kochujang powder and slowly frozen Kochujang powder, and raw Kochujang exhibited pseudoplastic behaviors with yield stress and presented thixotropic properties which followed the second-order kinetic behavior proposed by Tiu. Suspensions of Kochujang powders exhibited considerably higher decaying rates than raw Kochujang. The dependency of the equilibrium structure parameter on the shear rate was weak, and there were no significant differences among the values of structure parameters of three samples. The temperature dependency of the apparent viscosity of Kochujang suspension was fully expressed by Arrhenius equation and activation energies of suspensions of quickly frozen Kochujang powder and slowly frozen Kochujang powder, and raw Kochujang were 2.21, 2.18, and 2.32 Kcal/g.mole respectively. Consistency indices of three samples increased with solid content and decreased with temperature. Flow behavior indices of three samples showed no considerable dependency on the temperature and solid content. There were no significant differences in the rheological properties between two Kochujang powders.
In Korea-LTPP(Long Tenn Pavement Performance) project, the full depth asphalt pavement test sections are constructed on the national highway to evaluate the structural capacity of asphalt pavement reinforced with glass fiber. Truck loading test and FWD test were performed to measure the structural capacity of test sections. Test results showed that the reinforcement of glass fiber installed at between surface and intermediate asphalt layer decreased the strain at the bottom of surface layer and moved up the stress neutral axis in asphalt layer. As a result, the tensile stress was developed at the bottom of intermediate asphalt layer of reinforced asphalt pavement, while the compressive stress was developed at the bottom of intermediate asphalt layer of unreinforced asphalt pavement. On the other hand, the tensile strain at the bottom of asphalt base layer didn't show a difference between glass fiber reinforced and unreinforced pavements. From the FWD test, it was shown that the surface deflection of asphalt pavement reinforced with glass fiber decreased 24 percents comparing to that of unreinforced asphalt pavement. This shows that the reinforcement with glass fiber appears to improve the rutting resistance of asphalt pavement.
Journal of the Korea institute for structural maintenance and inspection
/
v.22
no.1
/
pp.147-157
/
2018
The basis of capacity design has been explicitly or implicitly regulated in most bridge design specifications. It is to guarantee ductile failure of entire bridge system by preventing brittle failure of pier members and any other structural members until the columns provides fully enough plastic rotation capacity. Brittle shear is regarded as a mode of failure that should be avoided in reinforced concrete bridge pier design. To provide ductility behavior of column, the one of important factors is that flexural hinge of column must be detailed to ensure adequate and dependable shear strength and deformation capacity. Eight small scale circular reinforced concrete columns were tested under cyclic lateral load with 4.5 aspect ratio. The test variables are longitudinal steel ratio, transverse steel ratio, and axial load ratio. Eight flexurally dominated columns were tested. In all specimens, initial flexural-shear cracks occurred at 1.5% drift ratio. The multiple flexural-shear crack width and length gradually increased until the final stage. The angles of the major inclined cracks measured from the vertical column axis ranged between 42 and 48 degrees. In particular, this study focused on assessing transverse reinforcement contribution to the column shear strength. Transverse reinforcement contribution measured during test. Each three components of transverse reinforcement contribution, axial force contribution and concrete contribution were investigated and compared. It was assessed that the concrete stresses of all specimen were larger than stress limit of Korea Bridge Design Specifications.
This study investigates the physical properties and manufacturing method of shape memory fabric for emotional garment made by polypropylene. For this purpose, polypropylene(PP) POY and SDY were texturized using low temperature and constant length heat treatment texturing technologies, respectively. The shape memory fabrics made using these texturized PP yarns were woven with two kinds of PET and PTT shape memory yarns on the air-jet loom and the various physical properties of four kinds of shape memory fabrics were measured and discussed. The tenacity and breaking strain of PP texturized yarns treated by low temperature and constant length heat treatment showed high weaving efficiency and the wet thermal shrinkage of PP textured yarns was shown less than 1.5%, dry thermal shrinkage was ranged between 3% and 5%, which means thermal stability compared to the PTT textured yarn with high thermal shrinkage, 5~8%. The shape memory characteristics of PP shape memory fabrics measured by Toray method showed five grade as same value as PTT shape memory fabric. The heat keeping property of the PP shape memory fabric showed 56% higher value than that of PTT shape memory fabric. The water repellency of PP shape memory fabric measured by spray method showed five grade as same value as PTT shape memory fabric treated with water repellent agent. Especially, shape memory properties of PP shape memory fabric measured by 3-D image and camera measurement methods showed similar characteristics to the PTT shape memory fabric.
Emulsions were prepared with the inversion emulsification method which adopted the agent-in-oil method-dissolving the mixed surfactants composed of the glycerin monostearate, polyoxyethylene(100) monostearate, and polyoxyethylene(20) sorbitan monostearate into mixtures of liquid paraffin and beeswax, and adding the aqueous solution of propylene glycol, gradually-and then their phases and viscosities behaviors in the emulsifying process were investigated. The fine and homogeneous o/w emulsions were formed in the HLB region (HLB 10.1~12.3), showing liquid crystalline phase and white gel phase in the emulsifying process. The phase inversion steps in the emulsifying process appeared as follows, i.e., oil continuous phase${\rightarrow}$liquid crystalline phase${\rightarrow}$white gel phase${\rightarrow}$o/w emulsion. Shear rate-shear stress curves of the prepared emulsions had the yield values which pointed out the existence of inner structure between emulsion particles, and the hysteresis loop which showed that the inner structure wasbroken irreversibly by the shear. The area of hystersis loop, an index of breakdown of inner structure, was increased with the decreasing of the HLB value of emulsifier, Shear time-shear stress curves showed the time dependence of plastic viscosity, and the relaxation time in time thinning behavior(${\lambda}$) indicated that the stability of emulsions prepared with the inversion emulsification method was decreased with the increasing of HLB values of emulsifier and was higher than that of emulsions prepared by homomixer.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.