• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.131-138
• /
• 2003

This paper considered the structural mechanism of transitional boundary layer by the experimental approach. In order to measure the turbulence quantity in the boundary layer, we made a wind tunnel with 400${\times}$190${\times}$2500 mm test section and a flat plate with well fabricated leading edge. Hot wire anemometer was used for acquiring the continuous turbulence signal which is processed by special software. The results of experiment show that the region where turbulence spot is dominant moves from near wall to overall layer and thus the anisotropy of velocity fluctuation shows so large value. Also the turbulence energy originally contained in low frequency band comes up to the high frequency band. Finally the turbulence model needs minimum two length scales to consider the pre-transition region.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.4
• /
• pp.1-11
• /
• 2004

Numerical analyses on the aerodynamic characteristics of a counter rotating axial flow fan were conducted for the development of an axial type in-line duct fan. The counter rotating fan has a front rotor and a rear rotor which are counter rotating each other. Blade design of the counter rotating fan was done by extension of design method for axial flow fan which consists of rotor and stator blades. Through flow analysis was performed using matrix method which is applied for flow fields prediction of compressors or turbines. Aerodynamic characteristics and characteristic curves of the counter rotating fan were analyzed by expansion of the frequency domain panel method with duct modeling. Pressure losses were higher at leading edge and hub region of rotor blades. Characteristic curve of the counter rotating fan was overpredicted without consideration of viscous effect.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.766-774
• /
• 2017

Software has been developed for simulating particle dispersion in a circular pipe with sudden-expansion, which models the fuel feeding system of a combustor that uses metal powder like aluminum as fuel. The Lagrangian based discrete tracer point method was employed for a plug flow of particles that satisfies local turbulent velocity fluctuations. A radial velocity component was created to improve the flow turning outwards in the recirculation zone. The particle distribution patterns from both with and without the component were directly compared with the experiments near the reattachment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.249-249
• /
• 2011

전력용 개폐장치인 진공차단기의 차단부가 송배전 시스템에 30 [kA] 정도의 커다란 사고전류가 흐르는 것을 방지하기 위하여 동작될 때 차단부 내부 전극 사이에 25,000 [K] 이상의 아크 플라즈마가 발생하게 된다. 두 전극 사이에 발생된 아크 플라즈마는 약 10 ms~20 ms 동안 지속되다가 교류전원의 전류영점 부근에서 회복된 절연성능으로 인하여 자연스럽게 소멸되지만, 대전류 구간동안 아크 플라즈마의 집중 현상 등에 의하여 전극의 심각한 손상 등이 발생되면 절연성능이 요구된 만큼 회복되지 못하여 사고전류를 차단하지 못하며 시스템에 연결된 기기들에게 심각한 손상을 입히고 정전사고를 일으킨다. 본 연구에서는 전자계-열유동 연성해석기법을 이용한 축자계 진공차단부에서 발생하는 아크 플라즈마의 3차원 수치해석을 통하여 전극의 심각한 손상을 입히는 아크플라즈마의 집중 현상에 관한 축자계의 영향을 고찰하고자 한다. 수치해석을 위한 아크 영역은 양극과 음극의 직경과 같은 직경의 원기둥으로 가정하였고, 전자계 해석으로부터 얻어진 로렌츠 힘과 줄열을 열유동 해석을 위한 Navier-Stokes 방정식의 파라미터로 입력하여 해석을 수행함으로써 전자계와 유체역학적인 영역을 동시에 연계한 순차적 일방향 연성해석 기법을 적용하였다. 컵형 축자계 진공차단부 내 아크영역에서의 로렌츠 힘의 특성과 온도분포에 대하여 수치해석을 수행하였고, 크기가 다른 두 로렌츠 힘에 의하여 양극표면으로 집중되는 온도분포의 크기를 비교함으로써 진공아크 플라즈마의 집중현상에 영향을 미치는 주요 요소를 규명할 수 있었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3022-3029
• /
• 2015

This study presents experiments to visualize the internal flow and heat transfer characteristics of thermosyphon with immiscible of water-FC40 adopted as binary working fluid. Three different regimes depending on the amount of heat flux applied to the thermosyphon were observed: natural convection, pulse boiling, and continuous boiling. Boiling incipience took place in water, which has lower vapor pressure than FC40. During natural convection water was vaporized in liquid pool while liquid film flows were formed. On the other hand, meanwhile bubbles were generated in the liquid pool during pulse and continuous boiling, the binary working fluid of water-FC40 was observed as the mixture throughout a whole range of the thermosyphon.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.277-281
• /
• 2000

본 논문에서 생체실험용 대형 2축 자기장 발생장치를 설계하였다. 생체실험 대상이 유동적이지 않고 홀더(holder)내에 고정될 경우 이는 방향성(orientation)의 논란이 불가피하며 이 영향을 줄이기 위해 각 축에 4개씩 총 8개의 코일을 사용하여 2축 4중코일 구조로 장치를 설계하였다. 원하는 특정 자기장에 대한 권선수 및 전류치를 결정하기 위해 정육면체 구조의 자기장 발생장치를 원통형으로 근사화시켜 간소하게 수식을 유도하였으며 각 코일의 최적위치 및 최적 권선비는 별도의 최적화 시뮬레이션을 통하여 수치를 추출하였다. 이렇게 얻어진 수치들을 MATLAB으로 제작한 시뮬레이터에 적용하여 설계 조건과 동일하게 모델링한 발생장치 주변에서의 자기장 분포를 시뮬레이션 해보았으며, 각 축에서의 균일도를 평가하여 균인 자기장 분포영역 또는 사용가능영역을 도출하였다. 장치해석 결과, 임의의 기준 자기장에 대해 약 5%의 오차범위를 인정할 경우, 최소 60% 이상의 사용가능영역을 확보할 수 있었으며, 이 영역 내에서는 고도의 균일 자기장이 분포함을 확인할 수 있었다.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.67-73
• /
• 2015

Using a computational fluid dynamics technique, the flow characteristics and particle residence time in a Taylor reactor were studied. Since flow characteristics in a Taylor reactor are dependent on the operating conditions, effects of the inlet flow velocity and reactor rotational speed were investigated. In addition, the particle residence time of $LiNiMnCoO_2$ (NMC), which is a cathode material in lithium-ion battery, is estimated in the Taylor vortex flow (TVF) region. Without considering the complex chemical reaction at the inlet, the effect of Taylor flow was studied. The results show that the particle residence time increases as the rotating speed increased and the flow rate decreased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.5
• /
• pp.399-406
• /
• 2014

Three-dimensional flow and aerodynamic loss in the tip-leakage flow region of a turbine blade equipped with both a pressure-side winglet and a suction-side squealer have been measured for the tip gap-to-span ratio of h/s = 1.36%. The suction-side squealer has a fixed height-to-span ratio of $h_s/s$ = 3.75% and the pressure-side winglet has width-to-pitch ratios of w/p = 2.64%, 5.28%, 7.92% and 10.55%. The results are compared with those for a plane tip and for a cavity squealer tip of $h_{ps}/s$ = 3.75%. The present tip delivers lower loss in the passage vortex region but higher loss in the tip-leakage vortex region, compared to the plane tip. With increasing w/p, its mass-averaged loss tends to be reduced. Regardless of w/p, the present tip provides lower loss than the plane tip but higher loss than the cavity squealer tip.

• The Journal of Engineering Geology
• /
• v.24 no.4
• /
• pp.525-534
• /
• 2014

Environmental problems typically occurring in abandoned mine lands (AML) include: contaminated and acidic surface water and groundwater; stockpiled waste rock and mill tailings; and ground subsidences due to mining operations. This study examines the effectiveness of various geophysical techniques for mapping potential hazard and contaminated zones. Four AML sites with sedimentation contamination problems, acid mine drainage (AMD) channels, ground subsidence, manmade liner leakage, and buried mine tailings, were selected to examine the applicability of various geophysical methods to the identification of the different types of mine hazards. Geophysical results were correlated to borehole data (core samples, well logs, tomographic profiles, etc.) and water sample data (pH, electrical conductivity (EC), and heavy metal contents). Zones of low electrical resistivity (ER) corresponded to areas contaminated by heavy metals, especially contamination by Cu, Pb, and Zn. The main pathways of AMD leachate were successfully mapped using ER methods (low anomaly peaks), self-potential (SP) curves (negative peaks), and ground penetrating radar (GPR) at shallow penetration depths. Mine cavities were well located based on composite interpretations of ER, seismic tomography, and well-log records; mine cavity locations were also observed in drill core data and using borehole image processing systems (BIPS). Damaged zones in buried manmade liners (used to block descending leachate) were precisely detected by ER mapping, and buried rock waste and tailings piles were characterized by low-velocity zones in seismic refraction data and high-resistivity zones in the ER data.

• Proceedings of the KIEE Conference
• /
• 2008.04a
• /
• pp.168-169
• /
• 2008

물체 인식에 사용되는 특징 벡터로 영역과 점이 있다. 우리는 영역 특징을 기반으로 하는 물체 인식 알고리즘과 특징점 정보를 기반으로 하는 물체 인식 알고리즘이 상호 보완될 수 있도록 하는 방범을 소개한다. 우리가 제안한 방법에서는 두 가지 알고리즘의 중간 결과가 상호 보완되게 함으로써, 물체 인식의 성능을 향상시키고자 하였다. 또한 두 가지의 물체 인식 알고리즘을 병렬 처리될 수 있도록 함으로써, 사용자로 하여금 신속하게 인식 결과를 확인할 수 있도록 하였다.