• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.7
• /
• pp.655-663
• /
• 2010

DUP (direct underside pressurization) is a device that can considerably increase lift, reduce take-off speed and minimize hump drag when a WIG effect vehicle takes off on the water surface. A 3-dimensional numerical investigation of a WIG effect vehicle with DUP is performed to analyze aerodynamic characteristics and the static height stability. The model vehicle, named Aircat, consists of a propeller in the middle of a fuselage, an air chamber under the fuselage, Lippisch-type wings and a large horizontal T-tail. The lift is mainly increased by the stagnation of the accelerated air coming into the air chamber through the channel in the middle of the fuselage. However, the accelerated air increases drag as well as reduces static height stability.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.34-34
• /
• 1998

차세대 비행체가 갖추어야 할 요건으로 다양한 작동 범위에서 다목적으로 사용될 수 있어야 한다는 점이다. 비행체는 작전시 초음속으로 순항해야 하며, 폭탄으로 손상된 비행장에서도 이륙하여 작동할 수 있도록 짧은 이륙과 착륙 거리를 가져야 하기 때문에 현재 비행체보다 더 큰 받음각에서 작동하여 비행시 뛰어난 기동성을 가져야 한다. 제어력을 향상시키기 위해서 받음각과 동압에 의존하지 않고 큰 제어 모멘트를 제공하는 차세대 방법은 엔진의 배기가스를 원하는 비행 방향으로 제어하는 것으로 이러한 방법을 추력 편향 제어(Thrust Vector Control)라고 한다. 기존 공력에 의한 비행 자세제어 방법은 속도의 2승에 비례하는 제어력을 발생하지만, 실속을 피해야하기 때문에 공기력을 이용한 날개 및 비행체의 받음각에 한계가 있어 비행체의 선회능력을 제한하며 고공에서 저속비행 하는 경우에는 공기의 밀도가 낮고 동압이 작게 작용하여 선회능력은 낮아진다. 그러나, 추력 편향 장치는 공력을 이용하지 않고 추력을 이용하기 때문에 실속에 의한 제한이 없어 큰 받음각(70$^{\circ}$-90$^{\circ}$)으로 선회할 수 있어 월등한 기동성을 발휘할 수 있다. 이러한 추력 편향 장치 중 제트 베인형은 소형화가 가능하고, 하나의 노즐로 수직, 수형 및 횡 방향의 3축 제어를 할 수 있어 많이 사용되고 있다.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.17 no.4
• /
• pp.70-75
• /
• 2009

According to the aviation statistics, tail strike incidents and accidents are cyclic. Although many tail strikes occurred during takeoff, these are less than during landing cases. Many cases are related on human factors. In my opinion it is possible to analyze the causes of takeoff tail strikes to some extent. There are major casual factors of tail strike during takeoff such as; (1) Mis-trimmed horizontal stabilizer (2) premature rotation prior to $V_R$ (3) Excessive pitch up rate during rotation (4) Improper use of the flight director. Among these causes improper use of flight director is excluded in this paper because it is recommended that pilot should use flight director after airborne. So I analyzed the other three causes as following. Firstly, because mis-trimmed stabilizer is related to center of gravity(CG), the relationship between stabilizer and CG is reviewed. Secondly, concerned premature rotation prior to $V_R$ I reviewed the background of rotation speed($V_R$) establishment and analyzed theoretically what speed leads to tail strikes. Thirdly, concerning excessive pitch up rate during rotation I analyzed what excessive pitch up rate can decrease ground clearance while using FDR data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.649-654
• /
• 2010

A three-dimensional numerical study of the WIG-effect vehicle with a direct-underside-pressurization (DUP) system and a propeller is performed to analyze the aerodynamic forces and moments acting on the vehicle. The computational model includes all the compartments of a WIG-effect vehicle, including a propeller in the middle of the fuselage and an air chamber under the fuselage. The DUP system and propeller help considerably reduce the take-off speed and minimize the effect of the hump drag when the vehicle accelerates to take off on water. The airflow is accelerated by a propeller, and the air then enters the air chamber through a channel in the middle of the fuselage, this air helps increase the lift since the dynamic pressure of air is converted to static pressure. However, the air accelerated by the propeller produces excessive drag and creates yawing moment. It is found that the effect of yawing and rolling moments on static stability is negligible.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.6
• /
• pp.468-477
• /
• 2014

In this research, how a solar powered HALE (high altitude long endurance) UAV (Unmanned Aerial Vehicle) can climb and reach mission altitude, 18km, starting from the ground using only solar energy. A glider type aircraft was assumed as a baseline configuration which has wing area of $35.98m^2$ and aspect ratio of 25. Configuration parameters, lift and drag coefficients were calculated using OpenVSP and XFLR5 that are NASA open source programs, and climb flights were predicted through energy balance between available energy from solar power and energy necessary for a climb flight. Minimum time climb flight was obtained by minimizing flight velocities at each altitude and total time and total energy consumption to reach the mission altitude were predicted for different take off time. Also, aircraft moving distances due to westerly wind and flight speed were calculated.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.471-474
• /
• 2006

GPS수신기는 항법센서로서 여러 분야에서 널리 사용되고 있다. 단일 안테나 GPS수신기로부터 일반적으로 위치와 속도 및 시간 정보를 얻을 수 있다. 그러나 고정익 항공기의 운동 특성을 고려하여 단일 안테나 GPS수신기의 측정치로부터 무인항공기의 자세를 추정할 수 있다. 이로써 단일안테나 GPS수신기를 이용하여 무인항공기의 자동 제어가 가능함을 이전 논문에서 보인 바 있다. 본 논문에서는 단일 안테나 GPS수신기를 무인항공기의 기본 센서로 사용하여 자동 이착륙이 가능함을 비행실험을 통해 보인다. 무인항공기의 반응속도와 강건성을 향상시키기 위해 rate gyros의 각속도 측정치를 이용한다. 또한 활주로에 자동착륙하기 위해서는 높은 정확도의 위치 정보가 필요하므로 DGPS를 이용하였다. 비행 실험 동안 무인항공기는 이륙에서 착륙까지 모든 과정을 자동 제어로 수행한다. 대부분 비행은 경로 제어로 이루어진다. 비행 실험 결과를 바탕으로 단일안테나 GPS수신기가 General Aviation 항공기나 무인항공기의 백업이나 저가의 제어 시스템을 위한 주 센서로서 사용이 가능할 것으로 판단된다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.12
• /
• pp.1087-1094
• /
• 2016

The responsibility of the vehicle holding device (VHD) is to hold the launch vehicle while it is stayed on launch pad and release the holding mechanism to allow a lift-off of launch vehicle at a moment of lift-off. During a release of the holding mechanism, in order to prevent the Ka doing a doing a doing mode which is vertical oscillation of entire liquid propellant and very severe for vehicle structure, gradual release of holding force is required. Also, a release operation of all 4 VHD should be synchronized very precisely. In this study, to comply the "gradual release and synchronized operation requirement", concept of VHD hydraulic system using an accumulator, pyro valve and orifice to control speed of hydraulic cylinder is proposed instead of using complicated hydraulic components. Then through multi-body dynamic analysis and computational hydraulic analysis, a size of orifice to meet a target speed of hydraulic cylinder is calculated. Through this study, simple and reliable VHD hydraulic system complying requirements is designed.

• Journal of Digital Convergence
• /
• v.13 no.11
• /
• pp.441-448
• /
• 2015

The purpose of the study was to perform a comparative analysis of the success and failure cases to increase the completeness of vault "Shirai-Kim Hee Hoon" technique. The subject of the study was "K" a male gymnast from Korean Artistic Gymnastic National team. The results obtained through the three-dimensional analysis during international as well as practice session are as follows: Firstly, excluding BC, the lead time in each PrF, HC and PoF phases were shorter during successful trials than in failure trials. Secondly, during successful trials, the horizontal and vertical velocity appeared to be higher during taking off, which contributed positively to the leaping motion in the horizontal direction. Thirdly, when compared with successful and failure trials, the body's angular rotation was highly maintained during the takeoff from the spring board followed by larger thigh angular displacement at the vault before actually attempting the backward rotation.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.50-55
• /
• 2004

Performance predictions of the propulsion system were conducted for a 900㎏ class Canard Rotor/Wing vehicle. The main components of the propulsion system are turbojet engine, exhaust ducts and nozzles. The internal flow of the duct was considered as one-dimensional, compressible and viscous flow. Adequate governing equations including centrifugal force effect were applied to the analysis of the duct flows. Results such as available power, available thrust, engine throttle, mass flow rates, rotor RPM and cruise nozzle area were presented for rotary-wing mode and transition mode.

• 해운
• /
• s.100
• /
• pp.19-30
• /
• 2013

하반기 산업경기는 현재 활주로에 이륙 대기 중인 비행기의 모습으로 묘사할 수 있다. 대부분의 산업경기가 저점을 형성하거나 회복국면에 진입할 전망이며 특히, IT산업은 빠른 성장세를 보이면서 가장 앞선 회복세를 보일 것으로 기대된다. 2013년 하반기 주요 산업별 경기 국면으로는 IT제조업은 반도체와 스마트 기기 중심의 수출 호조로 가장 빠른 회복 속도를 보일 것으로 전망된다. 또한, 석유화학산업은 상반기의 회복 추세가 하반기에도 이어질 것으로 보이며, 해운업은 제한적이나마 경기 회복 조짐이 나타날 것으로 예상된다. 한편, 하반기 중 건설업과 조선업의 업황 모두 경기 저점을 지날 것이라는 기대감이 존재하는 가운데, 자동차산업과 기계산업은 제한적인 수요 확대에 힘입어 경기 저점 형성 후 미약하나마 회복 국면으로 진입할 가능성도 있다. 하지만, 철강산업은 국내외 철강 제품의 수요 회복 지연, 시장 공급과잉 문제가 지속되면서 침체 국면에 위치할 것으로 전망된다. 다음은 현대경제연구원에서 최근 발표한 '하반기 산업경기의 5대 특징과 산업전망'의 주요 내용을 요약 정리한 것이다.