• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.151-161
• /
• 2017

A TSL (Thin Spray-on Liner) has a higher initial strength and faster construction time than conventional cementitious shotcrete. Because of its high adhesion and tensile strength, the TSL reinforced concrete show a characteristic like composite materials. In this study, to consider an application to the conventional design method, ASD (allowable stress design), numerical study was used. In the numerical analysis, material and contact properties were adopt from previous studies. Then a thickness of concrete in the tunnel was evaluated with the TSL reinforced case by the ASD concept. In other words, bending compressive stress, bending tensile stress and shearing force of the concrete were considered to determine a thickness of concrete lining by the given boundary conditions. From the numerical analysis, there was no tendency to show by the ASD because the ASD is based on the elastic theory while the TSL typically contributes to reinforcement after yielding.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.3
• /
• pp.23-30
• /
• 2012

For cracked concrete, it is obvious that cracks should be preferential channel for the penetration of aggressive substances such as chloride ions according to the previous researches. In order to extend the lifetime of cracked concrete, critical issues in the performance of the concrete is the risk of chloride-induced corrosion. Even though crack width can be reduced due to the high reinforcement ratio, the question is to which extend these cracks may jeopardize the durability of cracked concrete. If the size of crack is small, surface treatment system can be considered as one of the best options to extend the service life of concrete structures exposed to marine environment simply in terms of cost effectiveness versus durability performance. Thus, it should be decided to undertake an experimental study on the effect of surface coating system, which can be able to seal the concrete and the cracks to aggressive substances-induced corrosion in particular. In this study, it is excuted to examine the effect of surfaced treated systems on chloride penetration and carbonation through compressive stress induced cracks. Experimental results have showed conclusively that critical stress linked with deterioration, should be existed in compressive stress ratio 50 ~ 70% for chloride penetration and 70 ~ 80% for carbonation, respectively. When the critical stress is exceeded in concrete, a comparatively large deterioration was measured where the critical stress in concrete, the increase in the mass transportation is marginal in spite of the large increase in micro-cracks. As for the effect of surface coating system on crack-sealing, it can be seen conclusively that cracks can be healed.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.305-312
• /
• 2005

Poly(urethane-imide)s were prepared by reaction between crosslinkable endgroup containing soluble polyimide (PI) by chemical imidization and acrylate end-capped polyurethane (PU). Poly (amic acid) was prepared from 2,2'-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride (6FDA) and 4,4'-oxydianiline (ODA) and then end-capped with maleic anhydride (MA). The PU prepolymers were prepared by the reaction of polycaprolactone diol, tolylene 2,4-diisocyanate and end-capped with hydroxyl ethyl acrylate. The effect of PU content on the residual stress behavior, morphology and thermal property was studied. The poly(urethane-imide)s were characterized by thin film stress analyzer (TFSA), XRD, TGA and DMTA. Low residual stress and slope in cooling curve were achieved by higher PU content. Compared to typical polyurethane, these polymers exhibited better thermal stability due to the presence of the imide groups. Finally the residual stress of poly(urethane-imide)s was strongly affected by the morphological structure.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.293-302
• /
• 1991

The anomalous sea level deviation or storm surge caused by the typhoon Thelma in 1987 are studied analysing tidal observation data at 7 stations in the south coast of Korean peninsula. The surges are calculated by subtracting the predicted tidal height from the observed tidal record. The tidal deviation at these stations along the coast are discussed in association with meteorological data. The sea level anomalies are studied by means of the empirical orthogonal function (EOF) analysis and the fast fourier transform (FFT) method. The results of analysis suggest that the peak value of surges are higher at the tidal stations in semi-enclosed bay and in long narrow channel than at the ones facing with the open sea. From the result of EOF analysis, the temporal and spatial fluctuations of storm surge can be described by the first EOF mode, which explains 63% of the total variances during the passage of typhoon Thelma. The deviation of storm surge in the studied areas indicates bi-modal peak during the passage of typhoon Thelma. From the results of FFT spectrum analysis, the peak of energy of autospectrum for surge, atmospheric pressure, and wind stress appeared at low frequency fluctuations band of 0.008-0.076 cph over the 4 stations. Auto-correlation function of surge showed periodicity, while that of atmospheric pressure and wind stress indicates no periodicity. The result of FFT analysis shows that the typhoon surges are related chiefly with the change of atmospheric pressure in an open bay (Cheju Harbor), but with the wind stress in a semi-enclosed bay (Yeosu Harbor).

• Tunnel and Underground Space
• /
• v.29 no.3
• /
• pp.172-183
• /
• 2019

The generalized Hoek-Brown (GHB) failure criterion developed by Hoek et al. (2002) is a nonlinear function which defines a stress condition at failure of rock mass. The relevant strength parameter values are systematically determined using the GSI value. Since GSI index is a value quantifying the condition of in-situ rock mass, the GHB criterion is a practical failure condition which can take into the consideration of in-situ rock mass quality. Considering that most rock mechanics engineers are familiar with the linear Mohr-Coulomb criterion and that many rock engineering softwares incorporate Mohr-Coulomb criterion, the equations for the equivalent friction angle and cohesion were also proposed along with the release of the GHB criterion. The proposed equations, however, fix the lower limit of the minor principal stress range, where the linear best-fitting is performed, with the tensile strength of the rock mass. Therefore, if the tensile stress is not expected in the domain of analysis, the calculated equivalent friction angle and cohesion based on the equations in Hoek et al. (2002) could be less accurate. In order to overcome this disadvantage of the existing equations for equivalent friction angle and cohesion, this study proposes the analytical formula which can calculate optimal equivalent friction angle and cohesion in any minor principal stress interval, and verified the accuracy of the derived formula.

• Journal of Korea Water Resources Association
• /
• v.49 no.12
• /
• pp.1035-1044
• /
• 2016

In joint portions of the levee and the barrier, complex 3-dimensional flow was generated and collapse of revetment occurred frequently. For these reasons, it is necessary to install the joint revetment with greater stability as compared with the general revetment at the joint portions. However, design criteria for joint revetment was not presented in River Design Criteria (KWRA, 2009). Therefore it is necessary to research for engineering design of the joint revetment. In this study, hydraulic experiments were performed under various flow conditions in order to realize the collapse conditions of riprap and carried out in 20.0 m straight open channel with one side levee and the width was 4.0 m. The diameter of riprap covered around joint revetment was 0.03 m and the inlet discharges were $0.5{\sim}0.8m^3/s$. The numerical simulations were performed under same conditions with experiment. as results of this numerical simulations, the influence range was confirmed from the distribution of flow characteristics and shear stress. As a result, the riprap diameter of the joint revetment was calculated from 4.1 to 6.9 times greater than that of general revetment. As the inlet discharge was large, the range of vulnerable area was developed long in the downstream direction despite of same withdrawal velocity of riprap. Through this study, the methods of calculating the riprap diameter and influence range were proposed according to hydraulic characteristics of flow around joint revetment. At a later study, if additional experiments about effect of flood plane and various types of barrier is applied, it is expected that rational design method with stability of joint revetment can be proposed.

• Economic and Environmental Geology
• /
• v.53 no.2
• /
• pp.167-181
• /
• 2020

Analysis of variance (ANOVA) and multiple comparison analysis were performed for shear strengths categorized by breccia content of 5 wt.% (Case-I), 10 wt.%, (Case-II) and 15 wt.% (Case-III) in fault cores. The relationship between breccia contetnt and shear strength was quantitatively classified by calculating the mean and standard deviation of shear strength for each population in each case and then the grouping the breccia contents that had a statistically similar effect on the dispersion of shear strength. As a result, shear strength was clearly classified into group 1 (breccia content of 0-15 wt.%) and group 2 and 3 (breccia coantent of 15-30 wt.% and 30 wt.% or more) in Case-III. Shear strength of the standard line at breccia content of 15 wt.% were determined to be 43.6 kPa, 77.6 kPa, and 118.6 kPa at each normal stress (54 kPa, 108 kPa, and 162 kPa), respectively. In addition, the distribution range of cohesions is 0-43.6 kPa at breccia content of 15 wt.% or less, and 0-70.0 kPa at 15 wt.% or more. Distribution range of friction angles is 0-45.7 ° at breccia content of 15 wt.% or less, and 16.7-57.5 ° at 15 wt.% or more.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.8
• /
• pp.551-557
• /
• 2022

LRU (Line Replacement Unit) modifications are often required for military aircraft due to aging. Recently, LRU modifications were proceeded for KA-O (Armed Airborne Controller) by replacing the ejection seat and adding avionic equipment, which made the aircraft's operational CG (Center of Gravity) on fuel consumption curve become out of the range of the specification requested. The off-ranged CG should be corrected by introducing an appropriate method. This study proposes a procedure for revising and verifying the empty weight CG altered due to LRU modification for small military aircraft (e.g., KA-O). In the proposed method, first, the change of empty weight CG of KA-O due to the LRU modifications is comprehensively examined. Then, several ballast masses are added to the engine mount strut to restore the empty weight CG on the fuel consumption curve to a safe operational range. The installations are verified via stress and fatigue analysis for various operating conditions. Considering that open information is not very available for the revision of empty weight CG, this study is valuable because it presents an established procedure for correcting and verifying empty weight CG during aircraft modification.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.192-199
• /
• 2002

Largely, there are three kinds of the design criteria of piping system in petrochemical plant. The first is on the pipe thickness in accordance with the design pressure of piping system. The second is on the static state evaluation by thermal growth and the other is on the dynamic evaluation by piping vibration. According to the ASME B31.3 code, the internal pressure design thickness fur straight pipe shall be calculated as a code formula. And the static design by thermal displacement is defined 7000 cycles of fatigue life in operating the piping system with a design condition. However, the dynamic design evaluation in comparative with small displacements of high frequencies to the static condition has not established clearly the method, yet. So, this study purposes to present the trial of a proposal of dynamic design criterion on the basis of static design method.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.881-884
• /
• 2009

태양열을 이용한 발전은 신재생에너지 사업으로 현재 각광을 받고 있는 분야 중의 하나이다. 본 논문에서는 3kv급 태양열 집전기를 유한요소법을 이용하여 돌풍이 불 때 풍하중에 의한 안전성을 평가하였다. 태양열 집전기는 옥외에 설치가 되므로 바람에 대한 영향을 가장 많이 받게 되는데 풍하중은 특히 강한 태풍이 불 때에 가장 높은 설계변수로 자중이나 프레임이 태양을 트레킹 할 때 생기는 동역학적인 변수보다도 크게 된다. 기존에 풍압력에 대한 산술식이 있지만 구조에 따라 적용하는 방법이 다르므로 돌풍이 불 때의 풍속을 적용, 유한요소법을 이용하여 우선 플레이트 프레임 표면에 발생하는 표면 압력을 계산하였다. 구한 표면 압력으로부터 플레이트 부분에 작용하는 하중으로 환산을 구조물에 대입하였고, 구조물이 크고 Mesh수에 문제로 인해 프레임을 두 부문으로 나누어서 포스트 부문과 플레이트 부분에 적용하여 해석하였다. 포스트의 경우에는 플레이트에서 받은 풍하중을 벡터로 나누어서 적용하였고 플레이트 부분에서 작용하는 자중을 고려하여 적용하였다. 플레이트의 경우 돌풍에 안정적이라 하더라도 변형량이 높을 경우를 적용하였다. 포스트 부분과 플레이트 연결부에서도 보강을 통하여 적정범위의 응력이 집전기에 문제가 발생할 수 있으므로 적정한 범위의 변형량을 유지하기 위해 설계변경 하여 안전한 구조물이 되도록 하였다.