• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.21-29
• /
• 1999

The effects of density and pore size distribution of substrate in preparing SiC conversiton layer on graphite substrate were investigated. The chemical reaction for formation of SiC conversion layer was occurred at substrate surface or below surface through SiC gas infiltration. It was supposed that the pore size distribution required for the sufficient SiO gas infiltration and the continuous chemical reaction during conversion process was in the range of 1.0∼10.0$\mu\textrm{m}$. In the stress analysis of SiC layer with finite element method (FEM), the residual stress distribution due to thermal mismatch was shown. However, the compressive stress was measured in SiC layer by X-ray diffraction, it was presumed that the residual stress distribution of SiC layer was mainly influenced by the constraining effect of interlayer between SiC layer and graphite substrate, and the densification behaviro and the grain growth in SiC conversion layer.

• Geotechnical Engineering
• /
• v.14 no.1
• /
• pp.93-108
• /
• 1998

In this study, the analytic solutions and numerical methods were used to estimate the shape and size effects on the stability of underground openings. The stability of underground openings was evaluated by scrutinizing the effects of the rock mass quality, the state of in-situ stresses and the lateral earth pressure coefficient on the displacement, the stress concentration and the plastic region developed in the vicinity of the openings. The analytic solutions have shown that the stress concentration factor is inversely proportional to the radius of curvature of openings. Through parametric study on the various shapes and sizes of underground openings the characteristics of the controlling factors concerned with the stability were analyzed. Then, the study was extended to the horseshoe-shaped openings commonly used for under ground storage. Through the extended study the effects of the stress ratio and the height-towidth ratio of openings on the maximum displacement and plastic region developed around the openings were estimated. The results have shorn that the height-to-width ratio of domestic storage caverns can be increased economically without stability problem, as far as the lateral earth pressure coefficient is appropriate.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.766-774
• /
• 1998

32$0^{\circ}C$, 40%NaOH 용액의 autoclave에서 약 300wppm의 탄소를 함유하고 있는 15Cr-9Fe-balanced Ni 합금 판상시편에 대해 응력부식 저항성을 조사하였다. 부식시편은 $700^{\circ}C$, 100시간 동안의 열처리로 합금내부에 석출될 수 있는 가능한 한 많은 양의 크롬계 탄화물을 석출시킨 후, 다시 재용해에 의해 크롬계 탄화물의 형태를 조절하는 $800^{\circ}C$-$950^{\circ}C$범위의 최종열처리를 시행하고 급냉시킨 다음 U-자형으로 응력을 가하여 준비되었다. 최종열처리 온도가 올라감에 따라 시편들의 입계응력부식균열(IGSCC ) 전파속도는 $900^{\circ}C$까지는 거의 직선적으로 증가하다가 $950^{\circ}C$에서는 $700^{\circ}C$에서 얻은 값보다도 더 낮게 감소하였다. 즉, 크롬계 탄화물이 재용해되어 그 밀도가 감소함에 따라 IGSCC저항성이 감소하다가 완전히 재용해된 $950^{\circ}C$ 열처리 조건에서 오히겨 가장 큰 IGSCC 저항성을 나타내었다. 이와같은 최조열처리 온도에 따른 니켈계 합금 600의 부식거동은 입계에 존재하는 크롬계탄화물의 형태변화 때문이 아니라 입계에서 탄소-크롬계 탄화물-크롬간의 상평형에 의해 이루어지는 탄소의 입계편석량이 크롬계탄화물이 존재할 때에는 열처리 온도에 따라 증가하다가 그것이 완전히 재용해 되었을 때 가장 낮아지기 때문인 것으로 생각된다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.2
• /
• pp.191-197
• /
• 1987

It has been well known that the fracture mechanics can be applied to large through crack growth. But the growth rate of small surface cracks initiated from a small defect under rotary bending fatigue tests can not be treated as a function of stress intensity factor range. In this paper, to investigate the growth behavior of surface small fatigue cracks in the view-point of both fracture mechanics and strength of materials, the fatigue test has been carried out on two kinds of plain carbon steels with a small surface defect. Applying the concept of the cyclic strain intensity factor range .DELTA. $K_{\epsilon}$/$_{t}$ to the analysis of small surface fatigue crack growth, it is found that the relationship between cyclic strain intensity factor range and crack growth rate shows linear relation on logarithmic coordinates regardless of defect sizes and two kinds of carbon steels.s.s.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.51-56
• /
• 1983

In the stability problem of the U-grooved plate, it has a circular hole, the site of the hole determines some different deformation mode when it was loaded. To determine the optimal position of the circular hole-center which not to get large distortion of the hole itself, in this paper, we studied the distributions of stresses in the neck area between hole and U-groove and the distortion mode of the deformed hole by B.E.M(Boundary Element Method) and compared with experimental results in four cases. For a distributed load, according to the center of the hole moves closer to the U-groove center (c.-c. line), the shape of the circular hole was transformed to the elliptical one(it's major axis perpendicular to the c.-c. line). In this problem, the results by Boundary Element Method was well accorded with Experiments.

• Journal of the Korean institute of surface engineering
• /
• v.18 no.3
• /
• pp.125-133
• /
• 1985

About 1 mm thick nickel electrodeposits were obtained from nickel sulphamate baths at 40 to 60$^{\circ}C$ over the range of current densities form 5 to 25 A/$dm^2$. Deposits from above about 1.2V of cathode overpotential had randomly distributed fine grains due to a higher nucleation rate and hence had a high hardness. A deposit obtained at 0.63 V had the [110] orientation with a field oriented fine structure which yield a relatively high hardness. Deposite obtained at the intermediate overpotentials showed the [100] orientation with coarse field oriented structure whose column width tended to decrease with increasing cathode overpotential, which, in turn, gave rise to an increase in hardness. Residual stresses of the deposits measured by X-ray technique were mostly tensile but did not exceed 80 MPa, and were occasionally very small compressive. The cathode current efficiency was above 90% in all the electrolysis conditions, whereas the anode current efficiency varied from 50 to 90% with current density, bath temperature and nickel chloride concentration, among which the chloride was the most influential.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.613-619
• /
• 2022

The extended Maxwell-Wagner polarization model is employed to describe the ER(Electrorheological) behavior of bi-dispersed ER suspensions, and solutions to the equation of motion are obtained by dynamic simulation. Under the same particle volume fraction, it is found that the dynamic yield stresses of uniform size suspensions do not depend on the particle size. Compared with uniform size suspensions, the dynamic yield stress is reduced for ER fluids consisting of two kinds of particles with different sizes. Compared with the dynamic yield stress behavior, for ${\dot{\gamma}}^*$≧0.01 the shear stress shows different behaviors depending on the particle sizes and the raio of different size particles. The simulation results show the nonlinear ER behavior (∆_𝛕 ∝ Eⁿ, n ≈ 1.55) of the conducting particle ER suspensions.

• 순환기질환의공학회:학술대회논문집
• /
• 2005.12a
• /
• pp.25-26
• /
• 2005

동맥경화의 재발생 위치는 속도와 전단응력 등과 같은 혈류역학의 인자들의 영향을 많이 받는 혈관형태를 가진 영역이다. 이러한 결과는 관상동맥에 동맥경화의 발생빈도를 조사한 결과와 일치하고 있으며, 즉 좌전 하행지, 회선지, 및 우관동맥 등의 동맥경화성 병변 발생빈도에서 좌전하행지가 가장 많은 빈도를 나타낸다. 따라서 동맥경화의 발생 및 재형성은 혈관의 동맥경화성 위험지역의 형태적 특징, 즉, 분지부의 위치, 길이, 각도의 변화 등에 따라 달라질 수 있음을 시사한다. 동일한 관상동맥이더라도 동맥경화의 발생이 용이한 형태가 있는데, 혈관의 형태학적 특성에 따란 혈류역학적 특성이 달라지고 동맥경화가 발생할 수 있는 가능성이나 진행과정이 차이가 날 수 있음을 말한다. 특히 임계치를 넘는 고전단응력은 혈관내피세포를 파괴하거나 손상을 주며, 반대로 임계치 미만의 저전단응력은 혈류의 정체시간을 길게 하여 양쪽 모두 동맥경화성 생물학적 반응을 유발 할 수 있며, 고전단응력과 저전단응력의 빈번한 맥동성 변화작용으로 혈관이 손상될 수 있는 한계범위를 넘어서게 될 때 내피세포의 방어체계를 파괴시키거나 혈관성형술후의 신내포세포 형성과정에서 생물학적 활성반응을 촉진하게 되는 환경을 제공하게 되어 동맥경화를 촉진한다고 할 수 있다. 즉 임계치 이상의 고전단응력이 나타나는 형태와 입구경계조건이 발생되면 내피세포 손상에 따른 혈전 현상의 발생가능성이 높아지며, 임계치 미만의 저전단응력이 발생되면 동맥경화성 죽상반 재형성에 영향을 미치게 한다. 결론적으로 동맥경화의 재발생의 기전은 변형된 혈관의 형태학적인 차이와 위치에 따라 서로 다른 혈류역학적 유발할 수 있는 물리적 환경을 제공하는 데에서 출발한다고 할 수 있다.$8.0{\sim}8.3$으로 알카리 쪽으로 이동하였다. 파일롯트 규모로 본 고정화 효소 충전탑(내경 30cm, 높이 85cm)에 의한 이성화당의 생산을 시도하였던바, 고정화 효소(350 IXIU/ml-R) 1리터가 30일동안에 약 293리터의 이성화당을 생산할 수 있는 것으로 나타났다.l plane에서 선수군(選手群)이 $62.7{\pm}7.36^{\circ}$로서 비선수군(非選手群)과 별(別) 차이(差異)가 없었고, horizontalplane에서는 선수군(選手群)이 $-23.5{\pm}7.2^{\circ}$로서 비선수군(非選手群)의 $-38.8{\pm}8.2^{\circ}$에 비(比)해 유의(有意)하게 높았으며 운동후(運動後) 양군(兩群) 모두 유의(有意)하게 높았다. QRS vector 길이에서 Frontal plane에서 선수군(選手群)이 $13.86{\pm}1.44\;mm$로서 비선수군(非選手群)의 $9.62{\pm}0.97\;mm$에 비(比)해 유의(有意)하게 높았으며 운동후(運動後)에도 유의(有意)하게 높았다. Horizontal plane에서도 선수군(選手群)이 $19.82{\pm}2.10\;mm$로서 비선수군(非選手群)의 $16.90{\pm}1.39\;mm$에 비(比)해 유의(有意)하게 높았고 운동후(運動後)에도 선수군(選手群)이 유의(有意)하게 높았다. 이상(以上)을 종합(綜合)해 보면 선수군(選手群)의 R파고(波高)가 비선수군(非選手群)에 비(比)해 운동후(運動後) 계속(繼續) 유의(有意)하게 높았고, $Rv_5$

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.306-315
• /
• 2010

The stress laminated timber, which could be manufactured by small dimension lumber on construction site, has high possibilities for bridges in remote area, such as recreation forest or forest road, because those bridges may be short span and low frequency in use. The stress laminated timber has merits of easiness for preservative treatment and transportation because it is manufactured with small dimension lumber. This study was carried out to analyze performances of stress laminated timber manufactured with preservative treated domestic pitch pine for developing structural design data for stress laminated timber bridges for vehicular traffic. Perpendicular to grain compressive performance by preservative treatment and bending performance by bored holes of pitch pine lumber was analyzed. Then, the effects of bending performance by pre-stress pressure, distance of bolts, number of laminations and planning were analyzed. Conclusively, planning of lumber was not necessary for manufacturing stress laminated timber, and 80% of bending stiffness criteria was maintained as pre-stress pressure was higher than 3.0 kg/$cm^2$. However, further researches are needed to define the effects of bolt distances and number of laminations. The results of this research would be basic data for design stress laminated timber bridges for vehicular traffic in Korea.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.4
• /
• pp.35-45
• /
• 2014

Limit equilibrium methods of slope stability analysis have been widely adopted mainly due to their simplicity and applicability. However, the conventional methods may not give reliable and convincing results for various geological conditions such as nonhomogeneous and anisotropic soils. Also, they do not take into account soil slope history nor the initial state of stress, for example excavation or fill placement. In contrast to the limit equilibrium analysis, the analysis of deformation and stress distribution by finite element method can deal with the complex loading sequence and the growth of inelastic zone with time. This paper proposes a technique to determine the critical slip surface as well as to calculate the factor of safety for shallow failure on partially saturated soil slope. Based on the effective stress field in finite element analysis, all stresses are estimated at each Gaussian point of elements. The search strategy for a noncircular critical slip surface along weak points is appropriate for rainfall-induced shallow slope failure. The change of unit weight by seepage force has an effect on the horizontal and vertical displacements on the soil slope. The Drucker-Prager failure criterion was adopted for stress-strain relation to calculate coupling hydraulic and mechanical behavior of the partially saturated soil slope.