• Magazine of the Korea Concrete Institute
• /
• v.16 no.4 s.81
• /
• pp.70-77
• /
• 2004

콘크리트 구조물에 대한 많은 기준들의 요건에 따르면, 휨을 받는 철큰 콘크리트(RC) 보의 압축부에서의 응력은 일반적으로 일축의 응력-변형을 관계를 이용하여 계산한다. 이와 같은 접근은 가끔씩 압축력을 받는 콘크리트에서 부서짐이 발성할 때 보의 구조적 거동을 재현하지 못할 수 있다. 결과적으로, RC 구조물의 지지력과 그들의 연성은 근사적으로 평가된다. 본 논문에서는 압축을 받고 있는 콘크리트의 postpeak 거동은 활동면을 이용하여 모델링되었다. 이 활동 면의 모멘트-곡률곡선에서 연화부분에 그 원인이 있다. 제안된 활동현상의 수학적 표현은 압축력을 받는 콘크리트(즉, 연화부분의 거동이 압축영역의 크기와 변형률구배(곡배)에 의존하는)에 있어서 특정한 응력-변형률 관계를 정의하는 것이 얼마나 어려운지를 보여주고 있다.

• Geotechnical Engineering
• /
• v.7 no.2
• /
• pp.5-26
• /
• 1991

The results of a laboratory investigation for the influence of soil sties history, relative density of sand, pile surface condition depth and diameter on the behavior of piles in uplift are presented. Ultimate Uplife capacity depends not only on the relative density of sand but soil horizontal stress. The phenomena of critical depth can be explained by change of horizontal stress with depth. The value of Ktan tends to decreases with increasing pile diameter.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.575-577
• /
• 2000

(100) single crystal Si은 좋은 anisotropy etching 성질과 기계적 강도를 가지고 있어 MEMS 구조용 소재로 사용되고 있다. (100) Si의 신뢰성 평가를 위하여 필요한 탄성계수를 측정하고 반복동작에 의한 응력에 의한 파손특성을 평가하기 위하여 micromachining을 통해 resonator를 제작하였다. Resonator의 공진주파수를 분석함으로써 탄성계수를 추하고자 하였으며 반복응력에 대한 파괴특성을 평가하기 위하여 공진 상태에서 파괴가 일어날 때까지의 사이를 수를 측정함으로써 반복음력에 대한 Si의 피로특성을 평가하고자 하였다. 실험 결과 (100) Si의 <110> 방향으로의 탄성 개수를 측정할 수 있었으며 Si의 미세파손의 응력에 대한 의존성을 평가할 수 있었다. 평가결과 Si의 미세파손 메커니즘은 억제된 균열의 진전에 의한 subcritical crack에 의한 피로파괴 현상보다는 과도한 스트레스에 의한 순간적인 균열전파에 의해 지배됨을 관찰할 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.2
• /
• pp.143-156
• /
• 2015

The stress and displacement fields at the crack tip were studied during the unsteady propagation of a mode III crack in a direction that was different from the property graduation direction in functionally graded materials (FGMs). The property graduation in FGMs was assumed based on the linearly varying shear modulus under a constant density and the exponentially varying shear modulus and density. To obtain the solution of the harmonic function, the general partial differential equation of the dynamic equilibrium equation was transformed into a Laplace equation. Based on the Laplace equation, the stress and displacement fields, which depended on the time rates of change in the crack tip speed and stress intensity factor, were obtained through an asymptotic analysis. Using the stress and displacement fields, the effects of the angled property variation on the stresses, displacements, and stress intensity factors are discussed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.5
• /
• pp.400-407
• /
• 2011

The stress distribution and stress amplitude of a membrane are major factors to decide the mechanical fatigue life of PEMFC (Polymer Electrolyte Membrane Fuel Cell). In this paper, mechanical stresses under operating hygro-thermal condition of the membrane are numerically modelled. Contact analysis between gas diffusion layer (GDL) and the membrane is performed under various temperature-humidity conditions. The structural model has nonlinear material properties depending on temperature and relative humidity. Several geometric conditions are applied to the model. The numerical analysis results indicate that deformations of the membrane are strongly related with assembly conditions of the fuel cell. The fatigue life is predicted for practical operating condition through experimental data.

• Food Science and Preservation
• /
• v.13 no.5
• /
• pp.555-562
• /
• 2006

This study was conducted to investigate the rheological properties of protein-bound polysaccharide powders (SD-1, 2, 3) using ultrafiltration (UF) and spray drying (SD) process from Agaricus blazei Murill. The calculated weight-average molar mass (Mw) in the positions at 29.7 mL (for SD-1), and at 27.8 mL (for SD-2), and at 18.7 mL (for SD-3) was $8.2{\times}10^3,\;9.6{\times}10^4$, and $5.9{\times}10^6g/mol$, respectively. As concentration increased the solution showed higher pseudoplasticity where the pseudoplasticity decreased as temperature increased. The flow behaviors of spray dried powder solutions were more fitted to Herschel-Bulkley equation than Power law equation. Apparent viscosity of SD-2 was more temperature-dependent than that of SD-1 and 3. However, the SD-3 tended to be more concentration-dependent than SD-1 and 2 as temperature increasing.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.197-207
• /
• 2000

A transient heat transfer analysis and thermo-elastic analysis have been performed for the residual stress distribution on the fillet weldment used by finite element method. Specimen is fabricated single-pass fillet welding. This computation was performed for conditions including surface heat flux and temperature dependent thermo-physical properties using by heat input as parameter. Also, cut-off temperature of residual stress estimation by thermo-elastic analysis is determined. The fillet weldment were measured to determined their residual stress distributions for using hole-drilling method. As result, it was found that large tensile residual stress is about material yield strength, and the numerical simulation results for finite element method similar to residual stresses by hole-drilling method and other exiting research. Also, cut-off temperature is effectively determined by temperature which calculated maximum thermal stress equal to material yield strength.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.59-66
• /
• 2004

Sand compaction pile (SCP)-improved ground is composite soil which consists of the SCP and the surrounding soft soil. When a surcharge load is applied to composite ground, time-dependent behaviors occur in the composite soil due to consolidation according to radial flow toward the SCP. In addition, stress transfer also takes place between the SCP and the soft soil. This paper presents the numerical results of cylindrical composite ground that was conducted to investigate smear effect on consolidation behaviors of SCP-improved ground. The results showed that the smeared zone of soft clay had a significant effect on effective stress-pore water pressure response, stress transfer mechanism and stress concentration ratio of composite ground. Amount of stress transfer between the clay and the SCP was maximum in depth of z/H=0.25, and decreased with depth. Stress concentration ratio of composite ground was not constant, but depended on consolidation process. It was also found that the value of stress concentration ratio in soft clay with smeared zone was larger than that in soft clay without smeared zone.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.1
• /
• pp.18-26
• /
• 2004

In order to accelerate the rate of consolidation settlement, to reduce settlement, and to increase bearing capacity for soft ground under quay, sand compaction pile method (SCP) has usually been applied. SCP-reinforced ground is composite soil which consists of the sand pile and the surrounding soft soil. One of main important considerations in design and analysis for SCP-reinforced soils is stress concentration ratio according to area replacement ratio. In this paper, the numerical analysis was conducted to investigate characteristics of stress concentration ratio in composite ground. It was found that stress concentration ratio of composite ground is not constant as well as depends on several factors such as area replacement ratio, depth of soft soil, and consolidation process. The values of stress concentration ratio increase during loading stage due to stress transfer of composite soil, and reach up to 2.5∼12 according to area replacement ratio at the end of construction. After the end of consolidation, however, these values are converged to 2.5 to 6.0 irrespective of area replacement ratio due to increase in effective stress of soft soil during consolidation process.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.5
• /
• pp.82-88
• /
• 2011

In the present work, FEM analyses are carried out to investigate the fractures occurred within the structural part in the course of combustion experiment. The loss of structural integrity stems from the localized deformation and the damage induced due to a severe change in the thermal load. Moreover, the two-back stress evolution model is proposed using the Armstrong-Frederick and the Phillips' rules to depict the plastic deformation, and the continuum damage mechanics is also incorporated into the present model. It is noted that the present model is able to formulate a wide range of constitutive description with ease. The numerical results depicts that a severe strain localization and damage evolution can be obtained depending on the dominant back stress.