• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.292-297
• /
• 1986

Measurements of internal stress .sigma.$_{i}$, anelastic strain .epsilon.$_{A}$ and recovery rate .gamma. were made in steady state creep of 2024 Al alloys over a wide range of stresses at temperatures between 260.deg. C and 380.deg. C, for the purpose of investigating the relations among the three parameters. Values of .sigma.$_{i}$ were obtained by the method of strain transient dip test, and those of .epsilon.$_{A}$ and .gamma. were determined from the results of sudden stress removal or reduction tests. As a main result, it is thought that the anelastic behavior and recovery process are basically dependent on same deformation mechanisms.sms.sms.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.385-390
• /
• 2009

The gas turbine engine structures usually are placed on high thermal mechanical stress condition. For general low cycle fatigue evaluation, simple fatigue criterion based on critical plane approach is developed. LCF life of turbine wheel is evaluated with this criterion and process contrived together.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.4
• /
• pp.35-45
• /
• 2014

Limit equilibrium methods of slope stability analysis have been widely adopted mainly due to their simplicity and applicability. However, the conventional methods may not give reliable and convincing results for various geological conditions such as nonhomogeneous and anisotropic soils. Also, they do not take into account soil slope history nor the initial state of stress, for example excavation or fill placement. In contrast to the limit equilibrium analysis, the analysis of deformation and stress distribution by finite element method can deal with the complex loading sequence and the growth of inelastic zone with time. This paper proposes a technique to determine the critical slip surface as well as to calculate the factor of safety for shallow failure on partially saturated soil slope. Based on the effective stress field in finite element analysis, all stresses are estimated at each Gaussian point of elements. The search strategy for a noncircular critical slip surface along weak points is appropriate for rainfall-induced shallow slope failure. The change of unit weight by seepage force has an effect on the horizontal and vertical displacements on the soil slope. The Drucker-Prager failure criterion was adopted for stress-strain relation to calculate coupling hydraulic and mechanical behavior of the partially saturated soil slope.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.4
• /
• pp.69-78
• /
• 2022

Geotextile tubes are widely used to prevent erosion in coastal areas and to replace the backfill for shore slopes in the reclamation of land using dredged soil. In this study, The triaxial confining pressures were chosen as 10kPa, 50kPa, or 100kPa for the specimens reinforced with geotextile considering the condition in the site. The strain behavior under various compressive stresses was then identified. At strains 0% to 7%, the stress-strain behavior was the same due to the effect of initial strain hardening, in which the force was exerted according to the relaxation of the geotextile regardless of the confining pressure (≤100kPa). At strains of 7% or more, the specimen with the small confining pressure had smaller deformation under load, which increases the tensile resistance provided by the reinforcing geotextile. Brittle fracture was then observed due to strain softening and the deviator stress abruptly decreased. This is different from the phenomenon in which the shear strength increases as the confining pressure increases in general triaxial compression tests. In the geoxtile-confined tests, geotextiles are primarily subjected to tensile displacement. Thereafter, the modulus of elasticity increases rapidly, which exhibits the elastic behavior of the geotextile.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.251-258
• /
• 2000

Based on the numerical investigations using steel bridge pier subjected to strong seismic excitations a new approach to seismic damage assessment for steel structures and their members has been proposed in conjunction with the suggested definition of failure state. The relevant failure form of the steel pier is evaluated. It is revealed that when a seismic load has a short period, the failure of global buckling beyond the allowable displacement is more dominant than that by that of the local buckling caused by the accumulation of plastic strain. When a seismic load is not beyond this certain part, but repeats within the range of where a plastic deformation occurs, the plastic strain is accumulated on the partial element of bottom edge of steel pier and the failure occurs by the local buckling from the accumulated plastic local strain.

• Korean Journal of Materials Research
• /
• v.7 no.11
• /
• pp.951-956
• /
• 1997

Vacuum Hot Pressing을 이용하여 제조한 TiNi형상기억섬유 강화 6061 AI기지 복합재료를 제조하고 미세조직 및 기계적 특성 등을 연구하였다. 제조된 복합재의 항복응력은 예비변형량, 섬유체적율 및 열처리에 따라 증가하였다. 복합재의 지적특성은 예비변형이 가하여진 후 재가열되었을 때 기지 내 TiNi 섬유의 형상기억효과에 의한 압축잔류응력 발생에 기인된다. 미세조직 관찰 섬유와 기지 사이에는 AI$_{3}$Ti및 AI$_{3}$Ni의 금속간화합물층이 관찰되었다. 또한 시험온도 증가와 더불어 TiNi섬유강화된 복합재의 유동강도는 높은 값을 나타내었다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.1
• /
• pp.18-23
• /
• 2009

This study analyzes the thermal stress at automotive radiators on steady and transient states. The maximum displacement is shown at the lower corner of upper tank with the value of 0.51mm. The displacement becomes smaller at the center of radiator and it becomes larger at this edge. The maximum thermal stress with the value of 62 MPa is shown at the contact between upper tank and cooling plate. Thermal maximum stress with the transient state at the elapsed time of 10 second is lower than that at steady state as much as 0.7%.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.61-68
• /
• 2008

Resilient modulus has been used for characterizing the stress-strain behavior of subgrade soils subjected to traffic loadings. With the recent release of the M-E Design Guide, highway agencies are further encouraged to implement the resilient modulus test to improve subgrade design. The subgrade design for the trackbed, however, is primarily relying on the static test results such as $K_{30}$ and deformation modulus, Ev. Therefore applicability of the resilient modulus for the design of trackbed needs to be evaluated. In this study, physical property tests, unconfined compressive tests and resilient modulus tests were conducted to assess the resilient and permanent strain behavior of 14 cohesive subgrade soils. A predictive model for estimating the resilient modulus is proposed based on the results of unconfined compressive tests and tangent elastic modulus, unconfined compressive strength, failure strain, secant modulus at peak, and yield strain. The predicted resilient moduli using the predictive models compared satisfactorily with measured ones. Although the permanent strain occurs during the resilient modulus test, the permanent behavior of subgrade soils is currently not taken into consideration.

• Computational Structural Engineering
• /
• v.3 no.3
• /
• pp.53-54
• /
• 1990

응력 변형율의 관계가 시간에 대한 미분의 형태로 나타나는 비선형 탄소성 혹은 점탄소성 재질을 갖는 구조물이나 지만의 거동 문제를 유한요소법 등의 방법을 이용하여 해결하려고 하는 경우 주어진 외력에 의한 새로운 응력이나 응력 강화 현상을 표현하는 여러 재료 상수값들을 구하기 위해서는 적분을 요하게 되며 일반적으로 수치해석적 방법에 의해 수행된다. 이러한 수치해석적 적분방법은 보다 정확한 결과를 얻기 위하여 알고리즘 자체의 정확성과 안정성이 요구된다. 정확성은 수치해석적 적분방법이 적용될 수 있는 step size에 관계없이 거의 동일한 결과치를 얻을 수 있느냐 하는 것을 말하고 안정성은 큰 step size에서도 수렴된 결과치를 얻을 수 있느냐 하는 것을 의미한다. 그 뿐만 아니라 비교적 복잡하고도 그 대상영역이 큰 문제를 해석하고자 할 때는 수렴속도 또한 빠른 해석방법이 바람직하게 된다. 따라서 본 기사에서는 여러가지 가능한 수치해석 적분 방법을 소개하고 그들의 장단점을 논하고자 한다.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.1
• /
• pp.108-116
• /
• 1991

In the non-linear behavior of many materials, there is difference between the monotonic behavior by static load and the cyclic behavior by cyclic load. In particular, the short fatigue cracks to propagate in elasto-plastic stress concentrations(notches), are governed significantly by the cyclic behavior of materials. Accordingly, it is needed to investigate and compare the monotonic and cyclic behavior of materials. In the pressent study, the stress-strain relations of materials by monotonic and cyclic load tests were examined for 2 kinds of steels(SS41, HT80) and 5 kinds of Al-alloys(A5083-O, A6N01-T5, A7N01-T4, A7016-T6, A7178-T6). And the constants for mechanical properties of the materials were determined by experimental results, Moreover, when a notch was subjected to cyclic load, the effect of cyclic hardening property of materials on the variation of stress-strain amplitude in the notch tip was discussed by the application of Neuber's rule and experiments for a center notched plate.