• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.84-85
• /
• 2013

본 논문은 스파스 매트릭스 컨버터로 구동되는 유도전동기에 과도응답특성 개선을 위한 모델예측제어 기법을 제안한다. 제안하는 기법은 유도전동기의 파라미터를 이용하여 구한 예측 토크와 자속을 통하여 비용함수를 최소화하는 최적의 스위칭 상태를 결정한다. 시뮬레이션을 통해 제안한 제어 기법의 타당성을 검증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.2
• /
• pp.140-148
• /
• 2000

A robust current control technique with a simple time delayed estimator for a permanent magnet synchronous m motor (PMSM) drive is presented. Among the various CWTent control schemes for a voltage source inverter-fed P PMSM drive, the predictive control is known to give a superior performance. This control technique, however, r requires the full knowledge of machine parameters and operating conditions, and gives an unsatisfactory r response under the parameter mismatch between the motor and controller. To overcome such a limitation, the d disturbances caused by the parameter valiations will be estimated by using a" time delay contTol approach and u used for the computation of the reference voltages by a simple feedforwal"d control. The proposed control $ scheme is implemented on a PMSM using the software of DSP TlVIS:32OC:30 and the effectiveness is verified d through the comparative simulations and experiments.periments.

• Journal of Broadcast Engineering
• /
• v.4 no.2
• /
• pp.164-175
• /
• 1999

Based on the performance analyses for transmission channel and signal characteristics in digital satellite broadcasting system. the optimal design parameter values for system using QPSK modulation technique were proposed in this paper. The proper performance degradation were of 2.0dB for channel characteristics. O.4dB for transmission signal characteristics and 0.2dB for receiver characteristics. respectively. In this case. the design objectives for system parameters were within ${\pm}\;0.5dB$ for gain flatness in 27MHz bandwidth. and O.1nsec/MHz and $0.2sec/MHz^2$ for linear and parabolic group delay. respectively. Also. the optimal parameter values that provide the maximum availability were of OdB OBO for satellite transponder TWTA. and the optimal bandwidth for PLL circuit was of 40kHz with 0.707 damping factor. These analyses and design values can be available for high data rate transmission system via satellite.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.6
• /
• pp.698-703
• /
• 2003

This paper presents analog secure communication system about safe speech transmission using chaotic signals. We applied various conditions that happen in actuality communication environment modifying chaotic synchronization and chaotic communication schemes and analyzed restoration performance of speech signal to computer simulation. In transmitter, we made the chaotic masking signal which is added voice signal to chaotic signal using PC(Pecora ＆ Carroll) and SFB(self-feedback) control techniques and transmitted encryption signal to noisy communication channel And in order to calculate the degree of restoration performance, we proposed the definition of analog average power of recovered error signals in receiver chaotic system. The simulation results show that feedback control techniques can certify that restoration performance is superior to quantitative data than PC method about masking degree, susceptibility of parameters and channel noise. We experimentally computed the table of relation of parameter fluxion to restoration error rate which is applied the encryption key values to the chaotic secure communication.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.2
• /
• pp.118-124
• /
• 2010

In this paper, design parameters of dynamic vibration absorber, which is used to reduce bending vibrations of a vehicle drive line, is optimized. For obtaining the correct dynamic response characteristics, a flexible-body drive line is made by applying the flexibility data extracted from vibration analysis of propeller shafts to the drive line dynamic model. Inner tube mass, rubber stiffness and rubber damping coefficient of the dynamic vibration absorber are taken as design parameters for optimization. To minimize the vertical acceleration of the drive line, a second-order regression equation of the objective function is generated by performing the central composite experimental design with 3 factors, 2 levels and 15 test runs. And the design parameters of the dynamic vibration absorber are determined by using optimization program. The vehicle model with optimized dynamic vibration absorber reduces the vertical acceleration peak of the drive line by 17.1 % in compared with the initial model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.7
• /
• pp.694-704
• /
• 2011

In this paper, we present a design of a 5th order Chebyshev interdigital band-pass filter using inverter and susceptance slope parameter values obtained from EM simulated multi-port Y-parameters. The shifted length of the resonator is determined when the frequency of the transmission zero is separated far away from the center frequency. For the initial dimensions of the interdigital filter, the filter is decomposed into the individual resonators, and the dimensions are obtained using EM Simulation of the decomposed resonators. However, the interdigital filter with the dimensions determined from the EM simulation of the decomposed resonators shows slightly distorted response from the desired frequency response due to the coupling between non-adjacent resonators. To obtain a EM simulation dataset, EM simulation for this filter is carried out by parameter sweep with constant ratio for the initial values. In this dataset, it is determined the final values for the filter by optimization. The fabricated filter by PCB shows an upper-shift of center frequency of about 70 MHz, which was caused by permittivity changed and tolerance of fabrication.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.6
• /
• pp.21-28
• /
• 2007

Using multi-resolution, the mutiresolution proportional-integral-derivative(MRPID) controller functions as a filter to eliminate noise and disturbance which are included in error signals. If the sampling frequency is high, the response time will be delayed because of the remaining high frequency component although the overshoot is removed. However, if the sampling frequency is low, the response time will be enhanced by getting rid of signal components while the overshoot is increased. In this paper, the sampling frequency tuning method is used the response of the proportional integral derivative(PID) controller and the MRPID controller, and the parameter tuning method is considered the characteristic of the MRPID controller. The proposal method is verified by computer simulations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.402-405
• /
• 2012

In this paper, we proposed a novel metamaterial unit cell utilizing an interdigital capacitor(IDC) with non-bianisotropic property. Due to the induced magnetic resonance of an IDC unit cell, exotic effective constitutive parameters can be realized like a split ring resonator(SRR). Furthermore, the proposed unit cell is electrically smaller than a conventional SRR unit cell. The effective parameters retrieved from the transmission responses of waveguide measurement method and simulated results show good agreement.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.45.2-45.2
• /
• 2010

한국천문연구원은 한국우주전파관측망(Korean VLBI Network, KVN)에서 시험 운영 중인 한일공동VLBI상관기(Korea-Japan VLBI Correlator, KJJVC)의 핵심인 VLBI상관 서브시스템(VLBI Correlation Subsystem, VCS)을 제어하기 위해 CCS(Correlation Control Software)를 개발하였다. CCS는 명령어의 문법 검사를 하고, VCS와 TCP/IP 소켓으로 통신하여 명령어와 응답(reply)을 주고받으며, VCS의 실시간 요청에 대응하여 입력 지연 파라미터(delay parameter)를 자동으로 전달하는 소프트웨어이다. CCS는 사용자의 명령어를 local UNX FIFO를 통하여, 명령줄(Command Line)로 전달받고, 이러한 명령어들의 조합을 쉘 스크립트로 묶는 형태로 구성 되어있다. 그러나, 이렇게 명령어의 조합을 직접 편집하여 구성할 때, 입력할 명령어나 지연 파라미터의 구성이 복잡해지면, 스크립트에 필요한 명령이 문법에 맞지 않게 사용되거나, 일부 명령어가 누락될 수 있는 위험이 있다. 이러한 오류를 차단하고 작업 효율을 높이기 위하여, 상관 처리의 전체 운용 및 제어를 통합적으로 할 수 있는 사용자 인터페이스가 필요하다. 이를 위하여 KJJVC의 운용 및 제어를 위한 GUI를 설계하고 제작하였다. 개발된 GUI는 Python 언어를 기반으로 하는 wxPython 패키지를 사용하였으며, 사용자(Operator)가 명령어 문법이나 순서를 확인할 필요 없이, 관측 정보와 관측국 정보, 기록 매체 정보만 가지고 손쉽게 명령어의 조합을 생성해 주며, 시스템 초기화와 각종 정보의 입력이 직관적으로 이루어질 수 있도록 해 준다. 본 연구에서는 개발된 GUI의 설계 및 개발 과정과 시험운영에 대해 소개한다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.1-8
• /
• 2005

The calculation of parameters of a process model is modified to find better sliding mode controller for a process. A design method by Camacho has such problems as chattering and overshoot due to the Taylor the approximation errors for the time delay term of the first order model. In this paper, a new design technique for a sliding mode controller is proposed by introducing the modified Pade approximation considering the weight factor. With the proposed method, the process response can be directly used to estimate the system parameters without any numerical processing.