• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.761-768
• /
• 1999

This paper presents an NVH test of Automotive power steering system performed at a half-car Test-rig. The test was done for neutral and full turn(or relief) conditions in steering wheel at a fixed rpm first, then followed by the same conditions for the rpm run-up. The sound intensity measurement verified the results from the frequency and order analysis, especially about the identification of major noise sources and their dominant frequencies. The results from thie study can be utilized in the system noise tuning when a new steering component is installed. In particular, the noise and vibration reduction at the relief condition will be accomplished through the knowledge obtained from this study and from the on-going research on the hose tuning techniques usign silencers and tuning cable inserted in the pressure hose.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.603-608
• /
• 1998

In order to obtain basic data for the prediction of railway noise propagation, the noise radiation characteristics (source position, radiation directivity, etc) of trains were measured by using the sound intensity method. The measurements were performed at a side of railway by setting an intensity-probe array. As the measurement results, it was found that rolling noise due to interaction between wheel and rail and motor noise radiation from the lower part of train are dominant. The location of main sound sources can be described as being at the height of 0.1m in the center line of track, and the radiation directivity in the cross section of actually running trains are presented as a dipole source.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.7
• /
• pp.371-378
• /
• 2005

The objective or this paper is to measure the in-plane vibration intensity of a beam with a damped end that means the magnitude and direction of vibration power. Three experimental methods have been implemented to measure the in-plane vibration intensity over the beam. The first method is the accelerometer array method using two accelerometers. The second method is the frequency response function method using the only one accelerometer. The third method is the reference accelerometer method using a fixed reference accelerometer and another moving accelerometer. Those methods have been used to measure the spatial distribution of in-plane vibration intensity over the beam. The results obtained with those methods have been compared with each other. The results have been compared with an input power. It showed that the frequency response function method and the reference accelerometer method as well as the accelerometer array method can be effectively used to measure the in-plane vibration intensity in beams.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.83-92
• /
• 2000

Sound intensity method is well known as a visualization technique of sound field or sound propagation in noise control. Sound intensity or energy flux is a vector quantity which describes the amount and the direction of net flow of acoustic energy at a given position. Especially two dimensional sound intensity method is very useful in evaluating periodic characteristics and acoustic propagation mode of noise source. In this paper, we have studied the noise source Identification, acoustic sound field analysis, and characteristics of noise source of rotary compressor and scroll compressor for air conditioner using complex sound intensity method. Also we proposed a now method of time domain analysis which is used in evaluating of position of noise source in rotary and scroll compressor in this paper This paper presents the advantage, simplicity and economical efficiency of this method by analysing the characteristics of noise source with two dimensional complex sound intensity simultaneously.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.473-479
• /
• 1999

The two-microphone sound-intensity technique has been used for the detection of defects in ra-ally loaded ball bearings. The difference in the sound-intensity levels measured for bearings with no defect and for those with intentionally introduced defects of different sizes n heir elements under various operating conditions of loads and speeds is demonstrated. The results show that of an inner-race or ball defect. It is difficult to detect defects at lower speeds. Sound-pressure measurements were also performed for comparison and it shown that the detectability of defects by sound-intensity measurements is better than that by sound-pressure measurements.

• The Journal of the Acoustical Society of Korea
• /
• v.12 no.4
• /
• pp.39-46
• /
• 1993

조화집중이동하중을 받는 무한보에서의 음향방사에 대한 연구는 선박, 비행기, 타이어 트레드 밴느 등과 같은 계의 설계시 계의 구조물로부터 발생하는 소음에 대한 해결방안을 제시해 준다. 구조물 표면에 발생하는 음향파워는 svktnqusghks방법을 이용하여 보의 전길이에 분포된 음향 인텐시티를 적분하여 구한다. 보의 표면에서 발생하는 음향파원는 미하수, 장력, 감쇠계수, 기초강성계수, 그리고 파수비에 의해서 결정된다. 각 인자에 따른 음향파워에 대한 정성적인 분석을 수행하기 위해 심프슨 적분방법을 이용하여 수치적분을 하였다. 무한보에 작용하는 유체하중에 3다라 진동에너지가 음향에너지로 변환되는 비율이 달라진다. 밀도가 큰 유체는 등가감쇠로 작용하여 보로부터 방사된 음향에너지는 빠르게 감소된다. 하중의 이동에 의하여 도플러이동효과가 발생하여 무한보의 공진부근에서의 음향파워 파크가 분리되고 보의 기초감쇠의 영향으로 음향에너지는 감소된다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1053-1056
• /
• 2007

The acoustical performance of noise reducing devices installed on the top of a noise barrier were tested by small-scale outdoor tests. Noise measurements before and after installation of the devices were carried out using sound intensity methods. It is well known that the sound intensity method can specify the strength and directivity of sound, and it is convenient to consider the feature of sound around a noise barrier. The noise reduction effect of each edge device was evaluated using the difference between the input and output sound power levels calculated from sound intensities. It was investigated that each device had different efficiency in the shadow zone, while there was no significant difference between edge devices in the illuminated zone.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1990.10a
• /
• pp.35-40
• /
• 1990

본 연구에서는 덕트내 입사파와 반사파의 분리가 가능한 2개 마이크로폰법 (Two-sensor Method)의 입사파와 반사파의 분리측정 정밀도를 확인하고 이 방법에 따라 입사파 음향인텐시티만을 분리 측정하여 투과손실을 구하고 이 값과 ASTM E 477규격에 따른 삽입손실 측정값을 상호 비교검토하고자 한 다.

• 전기의세계
• /
• v.44 no.10
• /
• pp.40-46
• /
• 1995

소음을 줄이고자 하는 위치 혹은 공간의 선정문제, 또한 제어용 음파가 원래 제어하고자 하는 음파와 함께 섞인 상태에서 관찰하게 됨으로서 발생하는 문제, 제어용 음원의 위치 선정에 관련된 사항 등 가관측성 및 가제어성으로 대별될 수 있는 부분과 제어대상 물리량, 즉 제어대상 가격함수 선정의 물리적 적합성 등이 있을 수 있다. 전술한 가관측성 및 가제어성 관련 사항은 참고문허[3]에 비교적 상세히 기술되어 있으므로 본 고에서는 제어대상 가격함수의 선정과 관련된 음향학적 사실들을 중점적으로 다루도록 한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.500-505
• /
• 1997

이 논문은 초기 개발형태의 측정기와 지금까지 개발 개선되어 온 내용을 요약정리하고, 최근 개발내용을 함께 소개하며, 컴퓨터의 급속한 발달과 더불어 꾸준히 개발되어 온 BEM(boundary element method)을 이용한 소음해석결과를 측정결과와 상호 비교 검토함으로써 각기 방법의 정확성을 검증하고 있다.