• The Journal of the Acoustical Society of Korea
• /
• v.41 no.2
• /
• pp.242-253
• /
• 2022

When the source waveform is unknown, the Green's function can be estimated by Ray-based Blind Deconvolution (RBD) based on the simple array signal processing. In previous papers, RBD was successfully demonstrated using simulation and experiments in shallow water environment. In this paper, we investigate the applicability of RBD for a long-range communication (e.g., 30 km, 60 km, and 90 km) in a deep water environment (1,000 m ~), using experimental data conducted in the east of Pohang, South Korea, in October 2018. Data results are presented to demonstrate Green's function estimation of a communication signal (2.2 kHz ~ 2.9 kHz) using a 16-element, 42-m long vertical array. The results show that the Green's function estimated from RBD is comparable to that of matched filter result. Additional communication performance at a maximum range of 90 km will be also presented.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.4
• /
• pp.449-457
• /
• 2016

Cylindrical array sensor of a surface ship to detect an enemy is normally installed in the sonar dome. Reflected signals by some structures inside the sonar dome make unwanted signals. To minimize unwanted signals, acoustic baffles are used. Acoustic baffles are hard to install and replace, so the durability of acoustic baffles is an important design parameter. To verify the durability of acoustic baffle, accelerated aging tests according to temperature and pressure were performed. Acoustic baffle specimens were made and they are tested the visual and the performance (echo reduction and transmission loss) inspection before and after aging. After the inspection, the effect of accelerated aging of the acoustic baffles were discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.368-373
• /
• 2003

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of 4$\times$4 accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output con rot system. The theoretical and experimental study of sensor-actuator frequency response function sho vs that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15㏈ in vibration level and about 8 ㏈ in acoustic power level at the (1, 1) mode of the smart Panel. It has been also shown that the shaping error of PVDF actuator could limit he stability and performance of the control system.

• Tunnel and Underground Space
• /
• v.28 no.4
• /
• pp.293-303
• /
• 2018

Monitoring is the act of collecting and analyzing accurate engineering information using various methods and instruments. The purposes of the monitoring are design verification, construction management, quality control, safety management, and diagnose of structure etc.. The diagnose evaluation of the geotechnical structures corresponds to the confirmation of the structural performance. It is aimed to judge the soundness of geotechnical structures considering the degree of damage due to the environmental change and elapsed time. Recently, microseismicity, which is widely known in Korea, can be used for safety management and diagnoses of structure as it detects the micro-damage without disturbance of the structure. This report provides guideline on the procedure for assessing an underground oil storage cavern using microseismic monitoring techniques. Guidelines cover the selection of monitoring systems, sensor array, sensor installation and operation of systems, and interpretation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.281-287
• /
• 2001

For the conventional two-dimensional source location of acoustic emission (AE) based on the threshold crossing, wave velocity has to be measured in the actual structure to calculate the arrival-time difference and thus to form the two hyperbolae. Velocity is dependent on the fiber orientation, however, due to the dependence of elastic modulus on fiber orientation in anisotropic materials such as compost#e plates. This tan affect the accuracy of AE source location and make the source location procedure complicated. In this study, we propose a method to reduce the location error in anisotropic plates by using the numerical solution of nonlinear equations, where the velocity term has been removed by employing the fourth sensor. The efficiency and validity of the proposed method has also been experimentally verified.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.6
• /
• pp.678-686
• /
• 2019

Underwater communication performance is degraded by the influence of Inter-Symbol Interference (ISI) due to multipath. Passive time reversal processing is the most effective technique for mitigating multipath, and the diversity combining method can be used to improve its performance. This paper analyzed communication performance using the beam diversity combining method, which combines signals obtained through the beam steering to various angles. Directions of arrival were estimated through the beam-time migration, which, in turn, was estimated from probe signals received by a vertical line array. The performance was analyzed based on the number and type of combinations among the estimated angles. In this paper, the data obtained from the Biomimetic Long range Acoustic Communications 2018 (BLAC18) experiment, which was conducted in the East sea, ~50 km east of Pohang, in October 2018, were used for the analysis. The output Signal to Noise Ratio (SNR) was used as communication indicators.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.1
• /
• pp.89-94
• /
• 2024

Since Ultra-Short BaseLine (USBL) uses an array with narrow sensor spacing, precise synchronization is required to improve source localization performances. However, in the underwater environment, synchronization errors occur due to relatively strong noise and underwater acoustic channels such as multipath and Doppler, which deteriorates the source localization performances. This paper proposes a covariance-based synchronization compensation method to improve the source localization performances of the underwater USBL systems. The proposed method arranges the received signals through cross-correlation and calculates the covariance of the arranged signals. The synchronization error is related to the phase difference in the covariance. Thus, the phase difference is estimated as the covariance and compensated. Computer simulations demonstrate that the proposed method has better source localization performances than the conventional cross-correlation method.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.484-485
• /
• 2008

초음파는 의학적 진단 및 치료의 목적으로 널리 사용되어 왔다. 일반적으로, 초음파 조사의 생물학적 무해성은 많은 연구를 통하여 보고되었으나, 최근 초음파 집속을 통한 강력 초음파의 사용에 대한 열적 안전성 평가가 중요한 요소로 대두되고 있다. 이에 본 연구에서는 강력 집속 초음파의 전달 에너지와 열적 분포를 측정하여 안전성 평가에 활용 가능한 초음파 열분포 팬텀을 제안하였다. 온도 분포 측정용 팬텀은 초음파 조직유사 팬텀 재료인 한천을 이용하였으며, 음향학적 특성의 유사성을 평가하였다. 온도 효과를 측정하기 위하여 $3{\times}3$의 형태로 온도 센서를 팬텀 내부에 배열하여 초음파 조사에 따른 온도 분포를 측정하였고 온도 측정을 위한 시스템을 개발하여, 초음파 가열 실험을 수행하였다. 본 연구에서 제안된 초음파 온도 분포 측정용 팬텀의 유용성을 확인하였으며, 온도 분포용 팬텀을 통한 강력 집속 초음파 장비의 열적 성능 평가에 적용 될 수 있을 것으로 사료되었다.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.2
• /
• pp.110-117
• /
• 2016

Passive sonar systems detect and classify the target by analyzing the radiated noises from vessels. If multiple noise sources exist within the sonar detection range, it gets difficult to classify each noise source because mixture of noise sources are observed. To overcome this problem, a beamforming technique is used to separate noise sources spatially though it has various limitations. In this paper, we propose a new method that uses a FDICA (Frequency Domain Independent Component Analysis) to separate noise sources from the mixture. For experiments, each noise source signal was synthesized by considering the features such as machinery tonal components and propeller tonal components. And the results of before and after separation were compared by using LOFAR (Low Frequency Analysis and Recording), DEMON (Detection Envelope Modulation On Noise) analysis.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.237-245
• /
• 2003

Since the velocity is dependent on the fiber orientation in anisotropic composites, the application of traditional acoustic emission (AE) source location techniques based on the constant velocity to composite structures has been practically impossible. The anisotropy makes the source location procedure complicated and deteriorates the accuracy of the location. In this study, we have divided the region of interest(ROI) into a set of finite elements, taken each element as a virtual source, and calculated the arrival time differences between sensors by using the velocities at every degree from 0 to 90. The calculated and the experimentally measured values of the arrival time difference aye then compared to minimize the location error. The results from two different materials, namely AA6061-T6 and CFRP(uni-directional; UD, $[0]_{32}4$) laminate confirmed the practical usefulness of the proposed method.