• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.6
• /
• pp.811-819
• /
• 2019

Since the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the performance of various dynamic tests for seismic design has increased in Korea. However, sinusoidal load has been continuously used in the conventional laboratory tests to evaluate liquefaction potential and determine input-parameters in the numerical analysis. However, recent research results suggest that it is difficult to accurately simulate excess pore water changes of the ground under earthquake loads. In order to solve this problem, this study proposes a combined sinusoidal loading and examines its applicability to the cyclic shear and triaxial test. Also, its validity is examined through performing of shaking-table test and numerical analysis based on the effective stress model. As a result, it was found that the proposed combined sinusoidal loading can more accurately simulate the change of excess pore water pressure in saturated soils under real earthquake load than the sinusoidal load.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.3
• /
• pp.59-65
• /
• 2007

Excess pore pressures in low permeability soils may not dissipate quickly enough and decrease the effective stresses inside the soil, which in turn may cause a reduction of the shear strength at the interface between the soil and the reinforcement in MSE walls. For this condition the dissipation rate of pore pressures is most important and it varies depending on wall size, permeability of the backfill, and reinforcement length. In this paper, a series of numerical analysis has been performed to investigate the effect of those factors. The results show that for soils with a permeability lower than $10^{-3}cm/sec$, the consolidation time gradually increases. The increase in consolidation time indicates the decrease in effective stress thus it will result in decrease in pullout capacity of the reinforcement as verified by the numerical analyses. It is also observed that larger consolidation time is required for longer reinforcement length (longer drainage path).

• Geotechnical Engineering
• /
• v.6 no.4
• /
• pp.65-74
• /
• 1990

This paper presents triaxial test (CIVC and CKOUC) results on normally consolidated deep sea clay samples. Based on the test results the pore pressure-strain relations for both isotropicaly and anisotropicaly consgidated samples are expressed with hyperbolic functions of the major princpal strain. The analysis of the difference in pore pressure behavior due to the anisotropy in consolidation stress is carried out with the effective stress pathos of CIVC and CKOUC and finds a factor which correlates the pore pressure of two types of test.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.383-386
• /
• 2005

철근콘크리트 부재가 하중을 받을 때, 응력교란구역에서의 힘의 흐름은 스트럿-타이 모델을 이용하여 효과적으로 표현할 수 있다. 그러나 스트럿-타이 모델을 이용하여 철근콘크리트 부재의 해석과 설계를 하기 위해서는 큰크리트 압축스트럿이 가지는 유효강도를 정확히 산정하여야 한다. 본 연구는 철근콘크리트 부재에 휨과 전단력이 동시에 작용할 때 발생하는 대각선 균열이 콘크리트 압축스트럿에 미치는 영향에 대해 설명하고 있다. 대각선 균열의 발생 메커니즘과 이로 인한 콘크리트 압축스트럿의 강도 저하를 이론적으로 설명하였으며, 그 결과를 철근콘크리트 보의 강도 산정에 적용하였다. 최종적으로 철근콘크리트 보의 강도 예측값을 기존 연구자들의 실험결과와 비교하여 제안된 이론의 합리성을 검증하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.117-122
• /
• 2001

Many kinds of channels are used in industrial equipment and production machinery. Although mechanical saw has been used to cut many sorts of channels, there is cost rise problem because of low productivity. Shearing of channel has a special place because it helps to cut expected shape and size easily. A channel cutting die set which can be mounted and used on a hydraulic press is developed to improve the productivity of channel cutting process. Mode for the channel cutting is divided into single cut and double cut method. This study use double cut method, and the developed channel cutting die set is composed of upper and lower die set. Shearing time can be reduced from 40 minutes to 20 seconds using the developed channel cutting die set. The productivity of channel cutting process can be increased with shearing time reduction as well as cost reduction.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.180-195
• /
• 2000

Grouting has been practiced as a reliable technique to improve the mechanical properties of rock mass. But, the study of ground improvement by greeting is rare especially in jointed rock mass. In this study, joint compression test and direct shear test were performed on pure rock joint and cement milk grouted rock joint to examine the grouting effect on the property of rock joint. In the pure rock joint compression test, joint closure varied non-linearly with normal stress. But after cement milk grouting, the normal deformation characteristics of the joint was linear at the low normal stress level. As normal stress increased. deformation of the sample rapidly increased due to the stress concentration at the joint asperities. Peak shear strength of the grouted joint in low normal stress was higher than that of non-grouted joint due to the cohesion, decreased exponetially as the grout thickness increased. Thus after cement milk grouting, the failure envelope modified to a curve that has cohesion due to grout material hydration with decreased friction angle. Shear stiffness and peak dilation angle of the grouted joint decreased as the grout thickness increased. The peak shear strength from the direct shear test on grouted rock joint was represented by an empirical equation as a fuction of grout thickness and roughness mean amplitude.

• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.611-620
• /
• 2006

In the shear failure mechanism of a beam, beam and arch actions always exist simultaneously. According to the shear span to depth ratio, the proportion between these two actions is varied and the contribution of these actions to shear capacity is changed. Moreover, the current codes provide recommendations based on experimental results of normal strength concrete, so the application range of concrete strength must be extended. Based on this mechanism and new requirement, a simplified analytical equation for shear capacity prediction of reinforced high strength concrete beams without stirrups is proposed. To reflect the change in the contribution between these actions, stress variation in the longitudinal reinforcement along the span is considered by use of the Jenq and Shah Model. Dowel action with horizontal splitting failure and shear friction between cracks are also taken into account. ize effect is included to derive a more precise equation. Regression analysis is performed to determine each variable and simplify the equation. And, the formula derived from theoretical approaches is evaluated by comparison with numerous experimental data, which are in broad range of concrete strength(especially in high strength concrete), shear span to depth ratio, geometrical size and longitudinal steel ratio. It is shown that the proposed equation is more accurate and simpler than other empirical equations, so a wide range of a/d can be considered in one equation.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.307-317
• /
• 1999

The purpose of this study is to utilize conventional procedures for evaluation of liquefaction potential and to compare the results obtained by modified detailed method based on Korean earthquake magnitude (M=6.5). Liquefaction potential is assessed by comparing liquefaction strength of soil and cyclic shear stress generated in the soil layers during earthquakes. The cyclic shear stress is computed from the earthquake response analysis, and liquefaction strength of soil is evaluated by using results from cyclic triaxial tests. The cyclic triaxial tests are performed on many different conditions of sample ; relative densities(50%, 60%, and 70%), initial effective confining pressures (70kPa, 100kPa, and 150kPa), and fine contents(10%, 20%, and 30%). From the result of comparing the conventional procedure with the modified detailed method, it is found that the modified detailed method tends to evaluate larger safety factor against liquefaction in the weak sand site$(FS \leq1.5)$. Therefore in this case, it is suggested that liquefaction potential should be evaluated by using the modified detailed method based on cyclic triaxial tests. It is also found that in modified detailed method based on earthquake magnitude 6.5, critical depth where liquefaction can be generated is around 15m from the ground surface.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.3
• /
• pp.174-183
• /
• 2014

Seabed beneath and near coastal structures may undergo large excess pore water pressure composed of oscillatory and residual components in the case of long durations of high wave loading. This excess pore water pressure may reduce effective stress and, consequently, the seabed may liquefy. If liquefaction occurs in the seabed, the structure may sink, overturn, and eventually increase the failure potential. In this study, to evaluate the liquefaction potential on the seabed, numerical analysis was conducted using the expanded 2-dimensional numerical wave tank to account for an irregular wave field. In the condition of an irregular wave field, the dynamic wave pressure and water flow velocity acting on the seabed and the surface boundary of the composite breakwater structure were estimated. Simulation results were used as input data in a finite element computer program for elastoplastic seabed response. Simulations evaluated the time and spatial variations in excess pore water pressure, effective stress, and liquefaction potential in the seabed. Additionally, the deformation of the seabed and the displacement of the structure as a function of time were quantitatively evaluated. From the results of the analysis, the liquefaction potential at the seabed in front and rear of the composite breakwater was identified. Since the liquefied seabed particles have no resistance to force, scour potential could increase on the seabed. In addition, the strength decrease of the seabed due to the liquefaction can increase the structural motion and significantly influence the stability of the composite breakwater. Due to limitations of allowable paper length, the studied results were divided into two portions; (I) focusing on the dynamic response of structure, acceleration, deformation of seabed, and (II) focusing on the time variation in excess pore water pressure, liquefaction, effective stress path in the seabed. This paper corresponds to (II).

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.3
• /
• pp.160-173
• /
• 2014

Seabed beneath and near coastal structures may undergo large excess pore water pressure composed of oscillatory and residual components in the case of long durations of high wave loading. This excess pore water pressure may reduce effective stress and, consequently, the seabed may liquefy. If liquefaction occurs in the seabed, the structure may sink, overturn, and eventually increase the failure potential. In this study, to evaluate the liquefaction potential on the seabed, numerical analysis was conducted using the expanded 2-dimensional numerical wave tank to account for an irregular wave field. In the condition of an irregular wave field, the dynamic wave pressure and water flow velocity acting on the seabed and the surface boundary of the composite breakwater structure were estimated. Simulation results were used as input data in a finite element computer program for elastoplastic seabed response. Simulations evaluated the time and spatial variations in excess pore water pressure, effective stress, and liquefaction potential in the seabed. Additionally, the deformation of the seabed and the displacement of the structure as a function of time were quantitatively evaluated. From the results of the analysis, the liquefaction potential at the seabed in front and rear of the composite breakwater was identified. Since the liquefied seabed particles have no resistance to force, scour potential could increase on the seabed. In addition, the strength decrease of the seabed due to the liquefaction can increase the structural motion and significantly influence the stability of the composite breakwater. Due to limitations of allowable paper length, the studied results were divided into two portions; (I) focusing on the dynamic response of structure, acceleration, deformation of seabed, and (II) focusing on the time variation in excess pore water pressure, liquefaction, effective stress path in the seabed. This paper corresponds to (I).