• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.209-220
• /
• 2001

준설매립지반 표층강도증진을 위한 수평진공배수공법 적용시의 압밀현상 예측을 위한 연구를 수행하였다. 초연약지반에 수평배수재와 진공압을 이용하여 수평진공배수 공법을 적용할 경우, 배수재 부근에서 3차원적 배수특성과 넓은 범위의 유효응력의 변화, 지반의 압축성 및 투수성이 크게 변화하게 된다. 이를 위하여 3차원 배수특성과 다양한 경계조건, 부의 간극수압 발생을 통한 유효응력의 증가, 유효응력에 따른 압축성과 투수성의 비선형성을 포함할 수 있도록 기존의 3차원 압밀 지배방정식을 확장 유도하였고, 유효응력-간극비-투수계수의 관계를 누승형태의 함수로 표현하여 사용하였다. 해석기법의 타당성을 검증하기 위하여 실내에서 수행된 대형 토조실험 결과를 모델링하여 좋은 일치를 확인하였고, 이를 바탕으로 수평진공배수공법 적용시의 압밀효과에 대한 분석결과 드레인이 타설된 상부지반에서는 균등한 개량효과의 결과를, 하부의 미개량 지반에서는 자중압밀에 의한 압밀효과를 확인할 수 있었으며 배수재의 수평타설 간격에 따른 압밀효과 분석을 통하여 적정 배수재 설치간격의 범위를 확인하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2A
• /
• pp.81-92
• /
• 2010

In design of steel frames, it is generally believed that elastic system buckling analysis cannot predict real behaviors of structures, while inelastic system buckling analysis can give informative buckling behaviors of individual members considering inelastic material behavior. However, the use of Euler buckling equation with these system buckling analyses have the inherent problem that the methods evaluate unexpectedly large effective lengths of members having relatively small axial forces. This paper proposes a new method of obtaining elastic and inelastic effective lengths of all members in steel frames. Considering a fictitious axial force factor for each story of frames, the proposed method determines the effective lengths using the inelastic stiffness reduction factor and the iterative eigenvalue analysis. In order to verify the validity of the proposed method, the effective lengths of example frames by the proposed method were compared to those of previously established methods. As a result, the proposed method gives reasonable effective lengths of all members in steel frames. The effect of inelastic material behavior on the effective lengths of members was also discussed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.183-194
• /
• 2004

It's essential process to study non-linear material function related to characteristics of compressibility and permeability when we predict the consolidation behavior of soft clay ground. In this study, laboratory tests were conducted to find out the material function using marine clay. Standard oedometer test and Rowe cell test were performed with conditions, which were classified into vertical drainage only, radial drainage only and vertical-radial drainage case. Modified oedometer test equipment was developed to find out the material function and special extrusion device was originated to minimize the sample disturbance effect. Reliability of the results in modified oedometer test could be confirmed by comparing with the Rowe cell's one. Effective stress - void ratio - permeability relations were analyzed using all testing results. As a result, void ratio with effective stress level could be expressed by the power function and permeability with void ratio could be expressed by exponential function. In soft clay with high initial water content and low shear strength, non-linear characteristics related to compressibility and permeability varied with wide range by the effective stress levels. It's important to note that non-linearity of the material function should be considered at prediction of the consolidation behavior.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.2
• /
• pp.185-193
• /
• 2005

The present study composed a diesel-atkinson cycle of high expansion as a method of achieving high efficiency in diesel cycle engines. It also interpreted the cycle engine thermodynamically analysis to determine the possibility of the improvement of thermal efficiency and clarified the characteristics of several factors . According to the result of theoretical analysis, heat efficiency was highest when expansion-compression ratio Reど:1. In addition. diesel engines with high apparent compression ratio had higher expansion-compression ratio than otto engines and consequently their effect of high expansion was high. which in turn enhanced thermal efficiency. When the atkinson cycle was implemented in a real diesel engine by applying the miller cycle through the variation of the closing time of the intake valve, the effective compression ratio and the quantify of intake air decreased and as a result, the effect of high expansion was not observed. Accordingly. the atkinson cycle can be implemented when the quantity of intake air is compensated by supercharge and the effective compression ratio is maintained at its initial level through the reduction of the clearance volume. In this case. heat efficiency increased by $4.1\%$ at the same expansion-compression ratio when the apparent compression ratio was 20 and the fuel cut off ratio was 2. As explained above, when the atkinson cycle was used for diesel cycle. heat efficiency was improved. In order to realize high expansion through retarding the intake value closing time, the engine needs to be equipped with variable valve timing equipment, variable compression ratio equipment and supercharged Pressure equipment. Then a diesel-atkinson cycle engine is realized.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.09a
• /
• pp.399-403
• /
• 2003

해안의 연약지반에 건설되는 폐기물 매립지는 매립지의 안정성 평가를 위하여 하부기초지반의 침하거동 특성에 대한 분석이 필요하다. 본 연구에서는 현장 침하계측자료를 이용하여 현장 간극비와 현장 압축지수를 역산하여 그 특성을 분석하였다. 그 결과 매립초기에는 상부하중에 의한 유효응력증가가 미소하여 하부기초지반은 과압밀 특성을 나타내고 현장 압축지수 변화가 미소하였으나, 매립이 진행될수록 상부하중이 선행압밀하중을 초과하여 정규압밀영역으로 변화함에 따라 큰 폭의 증가를 보였다.

• Geotechnical Engineering
• /
• v.6 no.3
• /
• pp.65-76
• /
• 1990

A series of consolidated drained and untrained cubical triaxial tests were performed to investigate three dimensional strength characteristics of compressible sand. All specimens, which are formed by deposisting a fine sand loosely, were used. Failure strength in terms of effective stress analysis was greatly influenced by the variation of intermediate principal stress and so was failure criterion The adjusted effective frictional angles obtained by the stress state projected on the same octahedral plane showed almost same value, while the measured effective frictional angles showed considerable difference depending on the drainage conditions. Results of total stress analysis in undrained test turned out to fit Tresca's failure criterion well, but results of effective stress analysis turned out to fit Lade's failure criterion well.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.4
• /
• pp.343-351
• /
• 2010

Bending and axial compressive stresses are distributed across the whole upper flange of a box girder bridge which has the span-to-depth ratio (B/L) of below 0.5, according to Korea Bridge Design Specifications (Minister of Land, Transport and Maritime Affairs, 2005). Shear lag phenomenon, however, can take place in the construction phase of cable-stayed bridge, in which stresses combining bending moment due to dead weight and cable vertical compression are induced. This study aims to analyze the effective width of flange over which composite stresses are given, which should be calculated during the construction phase of stiffening girder of single plane cable-stayed box girder bridge. The study results indicate that the full width of stiffening girder can be regarded as the effective flange width when the span-to-depth ratio for the deck is below 0.38. In other words, the area, where shear lag is taken into consideration, is larger than the width of box girder in single plane cable-stayed box girder bridges. Therefore, the current practice of considering the full width as the effective flange width regardless of changes of the span-to-depth ratio during the construction stage can produce an unsafe bridge. If the effective flange width is determined according to the single span structural system in the early stage of construction when the span-to depth ratio for the deck is high and composite stresses of every part expect each end of the bridge are calculated, it can result in a safe structural design. Since the span-to-depth ratio gradually decreases, however, it is appropriate to determine the effective width of flange on the basis of the full width and the cantilever structural system.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.2
• /
• pp.169-179
• /
• 2005

An improved method for evaluating effective buckling lengths of beam-column members in plane frames is newly proposed based on system inelastic buckling analysis. To this end, the tangent stiffness matrix of be am-column elements is first calculated using stability functions and then the inelastic buckling analysis method is presented. The scheme for determining effective length of individual members is also addressed. Design examples and numerical results ?uc presented to show the validity of the proposed method.

• Journal of computational fluids engineering
• /
• v.1 no.1
• /
• pp.35-46
• /
• 1996

원심형 임펠러 내부 유로등 큰 곡률을 수반하는 터보기계 요소의 유동해석을 위한 계산코드를 개발하였다. 이 코드에서는 곡선좌표계에 유도된 3차원 비압축성 Navier-Stokes의 운동 방정식을 SMAC 음해법으로 푼다. 이 코드를 이용하여 유로의 단면이 정사각형이고 90도로 굽은 덕트내부의 층류 입구유동을 해석하고, 굽은 관 특유의 유동현상을 수치모사하였다 또한 곡관부 입구에서 충분히 발달한 유동, 또는 발달중인 유동이 유입될 경우에 이것이 곡관부 내부의 유동에 미치는 영향을 상·하류의 계산영역이 서로 다를 몇몇 유동장에 대하여 조사하고, 본 계산에서 얻어진 결과와 실형결과와의 비교로 본 3차원 유동해석 코드의 유효성을 검토 하였다.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.4
• /
• pp.66-73
• /
• 2004

Three species of Italian poplar (Populus euramericana), red pine (Pinus densiflora) and oriental oak (Quercus variabilis) were selected for this study. They were cut so that the distances between each of tips and roots for a pair of fingers were 0, 0.15, 0.30 and 0.45 mm. Poly vinyl acetate (PVAc) and resorcinol-phenol resin (RPR) were used for finger-jointing. Compressive test parallel to the grain was conducted for the finger-jointed specimens. The results were as follows: The efficiency of compressive Young's modulus of finger-jointed timber to solid wood indicated low values, whereas the efficiency of compressive strength indicated high values of more than 90% in all species, especially, it was found that those of red pine indicated markedly high values of more than 97%. The efficiency of compressive displacement of Italian poplar finger-jointed timber was 2 times higher than solid wood, and it was 1.2 and 1.3 times higher than solid woods in red pine and oriental oak, respectively. Also, it was found that 0, the distance between each tip and root for the fingers, indicated the highest efficiency of compressive strength performance in Italian poplar finger-jointed timber, and for red pine and oriental oak finger-jointed timbers, the distances of 0.15 and 0.30 were found to indicate the highest efficiency.