• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.6
• /
• pp.397-402
• /
• 2016

To produce adequate electricity in nuclear and thermal power plants, an optimal amount of steam should be supplied to a generator connected to high- and low-pressure steam turbines. A turbine output control device, which is a special steam valve employed to supply or interrupt the steam to the turbine, is operated using a hydraulic servo actuator. In power plants, the performance of servo actuators is degraded by the air generated from the hydraulic system, or causes frequent failures owing to an increase in the wear of the seal. This is due to the seal being burnt as generated heat using the produced compressed air. Some power plants have exhausted air using a fixed orifice, and thus they encounter power loss due to mass flow exhaust. Failures are generated in hydraulic pumps, electric motors, and valves, which are frequently operated. In this study, we perform modeling and analysis of the load-sensing air-exhaust valves, which can be passed through very fine flow under normal use conditions, and exhaust mass flow air at the beginning stage as with existing fixed orifices. Then, we propose a method to prevent failures due to the compressed air, and to ensure the control accuracy of hydraulic servo actuators.

• Journal of Engineering Education Research
• /
• v.4 no.2
• /
• pp.11-19
• /
• 2001

Current educational hydraulic oil systems consist of the composites for the hydraulic circuits. These systems not only could attract students' interests, but also increase the teaching efficiency during the lectures. Thus, the visual hydraulic oil system has been developed to enhance educational efficiency and to improve learning methods. With this new system, the students can easily examine the oil flow for hydraulic oil parts in mechanical engineering experiments. In order to develop the new system, the hydraulic constitute was made of acryl resin, and previous pipes were replaced by transparent and flexible tubes. Red colored oil was also used to visualize the oil flow. Furthermore, if OHP (Over Head Projector) was used for a theoretical lectures, the visual units can be used to classify the differences of the valve structure or the circuits. If lecturers use the developed visual hydraulic system, students can make an effective experiment on the basic theories and principles. Therefore, we can promote the students' interests and materialize the objectives of the subject. The results of this paper can be widely used to improve the efficiency of the mechanical engineering education.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.7
• /
• pp.138-147
• /
• 1995

The conventional PWM method, which was used in controlling the on-off valve, such as high-speed solenoid valve, was modulating the width of the pulse applied to the valve, by selecting arbitrary sampling time and modulating the duty-ratio in proportion to the error. However, in this method, a selection of long sampling time was inevitable and it was unable to get a high accuracy and a quick response. This study is for designing an appropriate controller for high-speed solenoid valve by proposing an improved duty-ratio modulation method using the Saw-toothed Carrier Wave which enables a short sampling time selection, high accuracy of control, and a quick response. Test which was carried out in the laboratory shows that transient and steady state response could be improved by PID controller.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.387-392
• /
• 1999

The micro electronic control technology with developing microcomputers make great contribution to electrohydraulic control systems. The electrohydraulic pulse control simplifies in conjunction with power electronic amplifier and high speed operated solenoid valves. It is necessary to valves to convert electronic pulse signal to hydraulic pulse flow as fast as possible. This study deals with the speed control of an oil hydraulic motor operated by two way high speed solenoid valves. The valves acts as converters of electronic-pulse signals to hydraulic power. By constructing systems in which a hydraulic motor is operated by two solenoid valves, the pulse with modulation method (PWM) has adopted as the speed control of hydraulic motor systems. The static and dynamic characteristics of the systems are investigated by the experiment. It is clarify that a hydraulic motor operated PWM show good performance as a control component, achieving accurate velocity control.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.3 no.1
• /
• pp.7-14
• /
• 2006

In this paper, an in-process diagnosis method for performance of position control servo system was studied, which was based upon null bias, slew-rate ratio and delay time measurement. Slew-rate ratio and delay time were analyzed by theoretical analysis, computer simulation and experiment. As a result of these analysis, when spool of servovalve was weared, slew-rate ratio was decreased and delay time was increased.

• Journal of Drive and Control
• /
• v.20 no.2
• /
• pp.1-6
• /
• 2023

This study aims to develop a Korean dental chair hydraulic circuit by improving the existing equipment in order to localize foreign leading companies' products. The suggested Hydraulic circuit can be applicable to varied sectors where height and backrest angle control of chair-type equipment are required. The study followed the steps below. First, three kinds of foreign hydraulic circuits were analyzed and three kinds of Korean dental chair hydraulic circuits were suggested. Second, it was determined whether the three kinds of Korean hydraulic circuits operate normally through SimulationX, a software specialized in multi domain analysis, and the effectiveness of each circuit was examined.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.2
• /
• pp.7-13
• /
• 2009

This study specifies the flow control characteristics of a flow control valve(FCV) in a submerged cargo pumping system through experiments and simulations. In the experiments, the functions of the major components of the FCV in relation to the FCV's flow characteristics are presented clearly. Through the simulations, it is shown that the simulation program suggested in this study can be utilized for the design of the FCV.

• 기계와재료
• /
• v.21 no.3
• /
• pp.42-51
• /
• 2009

원자력/화력 발전소에서 사용중인 터빈출력제어장치(turbine power control device)는 유압 서보액추에이터(hydraulic servo actuator)로 구동하는 특수 스팀 밸브(steam valve)로서 터빈의 속도를 제어하고 스팀을 차단하는 기능이 있다. 대형 발전기(500~1000Mw)를 구동하여 양질의 전기를 생산하기 위해서는 발전기에 연결된 고압 및 저압터빈에 최적량의 스팀을 공급하여야 하고, 고속(화력 3600 rpm, 원자력 1800 rpm)으로 회전하는 터빈이나 스팀계통에 이상이 발생할 경우 터빈의 과속(over speed) 방지를 위하여, 즉시 터빈으로 공급되는 스팀을 차단하여 터빈을 보호해야 한다. 따라서 터빈의 속도제어와 계통의 스팀 량을 감시하여 차단하는 발전소의 특수 밸브의 신뢰성확보기술이 요구된다. 특히 원자력발전소의 경우 핵연료교환주기(약 24개월)에 밸브들을 정비 또는 교체하고 있어 이때마다 시스템과 매칭(튜닝)기술이 요구되었다. 본 연구에서는 전량 수입에 의존했던 원자력/화력 발전소의 특수 밸브인 터빈출력제어장치의 국산화 개발과 신뢰성확보기술 효과에 대하여 논하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.9
• /
• pp.822-829
• /
• 2015

In this paper, the piezoelectric-hydraulic pump with a piezostack actuator as a driving source has been designed, fabricated, and evaluated for its application to UAV's brake system. The performance requirements of the piezoelectric-hydraulic pump were decided based on the requirements analysis of the target aircraft brake system. The geometric design of the piezoelectric-hydraulic pump to meet the performance requirements of the pump was conducted, and all components of the pump including the spring sheet type check valves were machined with close tolerance. By constructing a test apparatus for the performance check of the piezoelectric-hydraulic pump, the performance characteristics of the pump, such as the outlet flow rate for load-free condition and the outlet oil pressure for closed loop condition, have been evaluated. It has been found by the performance test result that the developed piezoelectric-hydraulic pump satisfies the design requirements effectively.

• Journal of Drive and Control
• /
• v.13 no.2
• /
• pp.26-33
• /
• 2016

This paper describes of a mathematical and real experimental analysis for a walking robot which uses servo valve driven hydraulic actuator. Recently, many researchers are developing a walking robot based on hydraulic systems for the difficult and dangerous missions such as walking in the rough terrain and carrying a heavy load. In order to design and control a walking robot, the characteristics of the hydraulic actuators in the joint through the view point of walking such as controllability and backdrivability must be analyzed. A general mathematical model was used for analysis and proceeds to position and pressure changes characteristic of the input and backdrivability experiment. The result shows the actuator is a velocity source, had a high impedance, the output stiffness is high in contact with the rigid external force. So stand above the controller and instruments that complement the design characteristics can be seen the need to apply a hydraulic actuator in walking robot.