• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.12
• /
• pp.82-89
• /
• 2006

This paper describes the development results of electrohydraulic actuation system which performs the attitude and trajectory control of pitch and yaw motion using thrust vector control for high altitude launching vehicle operated in high vacuum environment (altitude higher than 300 km). As compared with electrohydraulic actuation system for low altitude launch vehicle which operated under altitude of stratosphere, the intensified development requirements, newly adopted design and manufacturing technologies, newly developed test equipments and test results are summarized in this paper. The development test and evaluation of actuation system were successfully accomplished. The developed actuation system will be installed on KSLV-I after finishing verification of interface and integration compatibility with related other systems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.4
• /
• pp.401-407
• /
• 2016

For high fuel economy, many kinds of unit in vehicle have been developed. In steering system, as a result, HPS(Hydraulic Power Steering) system has been replaced as EHPS and EPS system. But the structures of these systems are totally different, and that causes the uncertainty of fuel economy evaluation. Therefore we undertake to research to find results and tendency of fuel economy and energy in steering system. For accurate evaluation, we modeled different types of steering systems on same vehicle model. The simulation came into action on various driving cycle. The driving condition is designed to show standby power of pump. Results show differences of fuel efficiency and energy consumption.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.402-412
• /
• 1995

A new energy conversion system which converts wind energy directly to heat instead of transforming it to electric power beforehand is suggested in this study. The new energy conversion system is composed of two big parts divided by their functions. One of them is a wind turbine part, and another is the heat energy conversion part. The object of this study is confined only to the heat energy conversion part, so the wind turbine is replaced with an electric motor for the convenience of experiment. In the experimental process, pressure difference at the hydraulic pump, revolution speed of the hydraulic pump, temperature at a few points on the oil circuit and the water circuit are measured at time intervals of five minutes. And integral values of input energy to the system and stored energy in the system is investigated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.6
• /
• pp.97-108
• /
• 1996

A modeling technique is proposed for dynamic simulations of OHC valve trains with HLA(hydraulic lash adiuster). HLA is expressed by an air-oil mixture model considering HLA leak-down and aeraton effects. A compact nonlinear equation is derived which describe the short term dynamic behavior of the HLA. Valve spring is analyzed by a distributed parameter model including nonlinear characteristics in the spring surge phenomena. Global behavior of the remaining valve train is expressed by a lumped mass model. The experiental results prove that the simulation model developed here is accurate and useful for the dynamic simulations of OHC valve trains with HLA.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.169-175
• /
• 2000

In this study, the hydraulic vibro-hammer system was analyzed and the analysis tool using GUI was developed. From the parametric analysis, the effects of each factor were revealed. Through the simulation with varying parameters, the method to improve the performance of the hydraulic vibro-hammer system was presented. The analysis tool will help an unskilled programmer analyze the hydraulic vibro-hammer system. The result of this study will help improve the performance of the hydraulic vibro-hammer systems.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.78-83
• /
• 2010

Since a tower crane is too high for a worker to ascend and by the wind in the high altitude, the possibility of a safety accident is very high, a lift assist is used. In this study, the hydraulic fall prevention device using the pressure generation device by Seok, et al. was developed. For this, the effects on the fall prevention performances of factors such as gear clearance, oil viscosity, rotative velocity and so on were evaluated by the analysis of fluid flow using FEM and the prototype was producted and a function test was performed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.683-686
• /
• 2007

The characteristics of radiated noise from the hydraulic breaker were measured under the revised regulation of Ministry of environment. The directivity of radiated noise was also measured at a distance of 7.5 m and a height of 1.5 m from the operating hydraulic breaker.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.1
• /
• pp.158-165
• /
• 2008

Hydraulic power steering system has been adopted in seniority passenger and commercial vehicle system for an easy maneuverability and a smoother ride. In this study, hydraulic power steering system analysis model which includes hydraulics and mechanical sub-systems was developed using commercial software, AMESim in order to predict characteristics for various steering components. Each component which constructs system was modeled and verified by experimentally obtained characteristics curves of each components. The agreement between simulation and experimental results shows the validity of the simulation model. The parameter sensitivity analysis such as valve opening area, torsional stiffness for system design are carried out by the analysis and experimental method.

• Proceedings of the KIEE Conference
• /
• 2008.04b
• /
• pp.19-21
• /
• 2008

현행 배전선로의 전주근가(1.2m 장방형)는 오거크레인을 이용한 건주공사 완료 후 전주근가 시공을 위한 별도의 인력 또는 백호우 장비가 추가로 투입피어 시공함으로써 인력으로는 공사시간이 장기간 소요되고 백호우장비로는 작업장 환경훼손과 시공원가 상승의 문제점이 있었다. 이러한 문제점을 해소하기 위하여 건주공사에 사용되는 오거크레인의 굴착 직경을 80cm까지 확장 가능한 '신축형 오거크레인용 유압식 확장기'와 원형 굴착공에 시공이 가능한 '아치형 전주근가'를 개발하고 이를 이용한 시공기술을 개발함으로써 동일장소에서 굴착작업이 수반되는 건주작업, 전주근가 매설작업을 가능하게 하여 장비활용성 증대, 작업장 환경개선, 공사기간 단축 및 시공원가 절감 등의 효과가 기대되는 기술을 개발하였다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.3
• /
• pp.41-47
• /
• 2003

In this study an elevator plant model is made with an electro-hydraulic servo valve and a single rod cylinder. A PID controller, a velocity feedback PID controller and a MRAC controller ate designed. Experimental apparatus including an elevator plant model and these controllers are constructed. In case of experiment, external load which is made with a hydraulic cylinder and a pressure control valve burdens varying load to the elevator plant model being driven. With experiment, the control performances of three proposed control methods are compared.