• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.481-492
• /
• 2018

The steel-plate concrete composite beam is composed of a steel plate, concrete and shear connector to combine two inhomogeneous materials. In general, the steel plate is assembled by welding an existing composite beam. In this study, the SPC beam was composed of folding steel plates and concrete, without a headed stud. The folding steel plate was assembled by a high strength bolt instead of welding. To improve the workability in a field construction, a hat-shaped cap was attached to the junction with a slab. Monotonic load testing under two points was conducted under displacement control mode to analyze the flexural strength of the SPC beam using a cap as the shear connector. Five specimens with shear connector types, protrusion length, and different thickness of steel plates were constructed and tested. The experimental results were analyzed through the relationship between the shear strength ratio and flexural strength in KBC 2009. The test results showed a shear strength ratio of more than 40 %. In the case of using a cap-like specimen as the shear connector, the flexural strength was 70% of the value calculated as a fully composite beam. In addition, the cap showed a smaller shear strength than the stud, but the cap served as a shear connection. When the thickness of the steel plate was taken as a variable, the steel plate exhibited a bending strength of approximately 70% compared to a fully formed steel plate, and exhibited similar deformation performance. Local buckling occurred due to incomplete composite behavior, but local buckling occurred at a 5% higher strength for a relatively thick steel plate. The buckling width also decreased by 15%.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.2
• /
• pp.193-201
• /
• 2014

This paper presents the development of simulation system on EPB shield TBM Hood operation. In recent, EPB shield TBM is widely used in the tunnel construction. Since the hood system of the EPB shield TBM is most important to excavate the tunnel, it is necessary to perform the simulation of hood system to investigate the design and operation parameters prior to tunnel construction. In order to carry out this study, the scaled simulation system was designed and developed. The model tests were performed to verify the developed system. During the simulation, the earth pressures developed in the chamber during tunnelling were measured to evaluate the operation technique. The test results obtained by the developed simulation system show clearly the similar behaviour of TBM hood compared with the field data. It was also found that the ground loss during tunnelling is dependent on the change of earth pressure in chamber. Therefore, the simulation system developed in this study will be very useful to evaluate the operation technique of the TBM hood prior to tunnel construction. In addition, this system will be applied in a various condition of ground to get the operating information.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.4
• /
• pp.237-242
• /
• 2009

In the pyroprocessing of spent nuclear fuels, fuel materials are recovered by electrochemical reactions on the surface of electrodes as well as stirring the electrolyte in electrolytic cells such as electrorefiner, electroreducer and electrowinner. The system with this equipment should first be scaled-up in order to commercialize the pyroprocessing. So in this study, the scale-up for those electrolytic cells was studied to design a large-scale system which can be employed in a commercial process in the future. Basically the dimensions of both electrolytic cells and electrodes should be enlarged on the basis of the geometrical similarity. Then the criterion of constant power input per unit volume, characterizing the fluid behavior in the cells, was introduced in this study and a calculation process based on trial-and-error methode was derived, which makes it possible to seek a proper speed of agitation in the electrolytic cells. Consequently examples of scale-up for an arbitrary small scale system were shown when the criterion of constant power input per unit volume and another criterion of constant impeller tip speed were respectively applied.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.4
• /
• pp.369-380
• /
• 2017

In order to manage the uncertainty about the evaluation and analysis of the human intrusion scenario of the Gyeongju Low and Intermediate Level Radioactive Waste(LILW) disposal facility, the calculation result by the GENII code was assessed using the RESRAD code, which was developed to evaluate the radiation effects of contaminated soil. The post-drilling scenario was selected as a human intrusion scenario into the near-surface disposal facility to analyze the uncertainty of the modeling by identifying any limitations in the simulation of each code and comparing the evaluation results under the same input data conditions. The results revealed a difference in the migration of some nuclides between the codes, but confirmed that the dose trends at the end of the post-closure control period were similar for all exposure pathways. Based on the results of the dose evaluation predicted by RESRAD, sensitivity analysis on the input factors was performed and major input factors were derived. The uncertainty of the modeling results and the input factors were analyzed and the reliability of the safety evaluation results was confirmed. The results of this study can be applied to the implementation 'Safety Case Program' for the Gyeongju LILW disposal facility.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.4 no.4
• /
• pp.12-20
• /
• 2001

The temporal variability in near-field mixing characteristics of discharging plumes in oceanic environment was investigated using the time series data of the buoyant jet parameters. Based on the currents and density profiles observed in Masan outfall site and effluent discharge flowrates for 63days of summer season, the temporal variabilities and those occurrence frequency were obtained by line plume equations. The results show that wide range of variability in Masan outfall's mixing characteristics was found due to the temporal changes of effluent flowrates and ambient oceanic conditions. The near-field dilution was in the range of 30~71 with the averaged dilution of 34, which was a good agreement with field measurements of salinity deficit. The length of mixing zone was in the range of 5.4~36.2 m with the average of 9.5 m, and the plume rise height was in the range of 8.1~10.2 m with the average of 8.9 m. However, only the 30~44% of the whole results are higher than the averages, which indicates the necessity of this frequency analysis with the continuously measured data for designing and managing the ocean outfall system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.278-284
• /
• 2017

In this study, the heat input conditions suitable for the AZ61 magnesium alloy were derived by controlling the welding speed at a constant rotational speed. In addition, from an economic point of view, industry demands higher welding speeds. Therefore,the effects of the welding speed were studied. The rotational speed applied was 800rpm, and the welding speed was varied from 100 to 500mm/min to evaluate the behavior of the welded regions. Tensile and hardness tests were conducted to examine the mechanical properties. Optical microscopy was used to observe the microstructure and soundness of the welded regions. Defects were observed at the welded region when the welding speed was more than400mm/min. As the welding speed increased, the grain size of the stir zone decreased and the hardness tended to increase proportionally. When the rotational speed was 800 rpm and the welding speed was 200mm/min and 300mm/min, there wereno defects in the welded region and excellent mechanical properties were recorded. In addition, the joint efficiencies were 100.5% and 101.2%, respectively, and the ultimate tensile strength was similar to that of the base metal. Fracture of the tensile specimen occurred between the advancing side and stir zone, and the fracture location coincided with the region where the hardness decreased temporarily.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.406-414
• /
• 2016

The lignin-based carbon nanofiber reinforced epoxy composite has been prepared by immersing carbon nanofiber mat in epoxy resin solution in order to evaluate the physical and mechanical properties. The thermal and mechanical properties of the carbon nanofiber reinforced epoxy composite were analyzed using thermogravimetric analysis (TGA), differential scanning calorimeter (DSC) and tensile tester. It was found that the thermal properties of the carbon nanofiber reinforced epoxy composite improved, with its glass-transition temperature ($T_g$) increased from $90.7^{\circ}C$ ($T_g$ of epoxy resin itself) to $106.9^{\circ}C$. The tensile strengths of carbon nanofiber mats made from both lignin-g-PAN copolymer and PAN were 7.2 MPa and 9.4 MPa, respectively. The resulting tensile strength of lignin-based carbon nanofiber reinforced epoxy composite became 43.0 MPa, the six times higher than that of lignin-based carbon nanofiber mats. The carbon nanofibers were pulled out after the tensile test of the carbon nanofiber reinforced epoxy composite due to high tensile strength (478.8 MPa) of an individual carbon nanofiber itself as well as low interfacial adhesion between fibers and matrices, confirmed by the SEM analysis.

• Korean Journal of Plant Resources
• /
• v.24 no.5
• /
• pp.499-506
• /
• 2011

The purpose of this study was to search available resources for new natural colorants. The extraction efficiency of colorants from black cowpea seed coats and their storage stability were examined according to the various extraction and storage conditions in this study. The results obtained were as follows: the optical density (O.D.) values of the extracted colorants increased with increasing extract time and temperature. Extraction at pH 4 was seen to be the most efficient among the various pH conditions. The color of the extract solutions were seen to change with variation in pH, for example, anthocyanins display color changes from orange-red, to orange, to blue, to greenish-blue at pH 3.0, 4.0-6.0, 7.0 and 9.0-11.0, respectively. The color changes of the extract solutions over various storage periods were determined using UV/Vis spectra these color changes indicate characteristic absorption patterns and a discoloration index which indicates the rate of absorbance (532 nm/454 nm). Methionine addition influenced the storage stability of the colorant solutions and this addition led to better storage stability than non-addition. In paper chromatography of juice extracted colorant, a long stripe was seen on development. Among three colorants obtained via paper chromatography according to development rate, at least two different colorants were mixed indicated by the appearance, or not, of a shoulder at 552 nm depending on the extent of development.

• Journal of Korea Water Resources Association
• /
• v.51 no.8
• /
• pp.729-737
• /
• 2018

This study investigates the sediment processes the Improved-pneumatic-movable weir through laboratory experiments considering changing channel slopes. Experimental results show that the delta migrates towards the weir and the delta height increases as time passes. Moreover, as the delta approaches the weir, the delta migration speed decreases. As the dimensionless delta location increases, the effective height of dimensionless delta and the dimensionless reservoir capacity increases. Therefore, under the same slope conditions, the sediment deposition volume of the delta is small as the channel slope is mild. This means that the channel slope affects the development of the delta in the upstream of the Improved-pneumatic-movable weir. At the beginning of the experiment, the foreset slope is mild. However, the foreset slope of the delta increases with water depth as the delta migrates downstream. Moreover, as the slope is mild, the ratio of delta front length to delta height is close to 1, and the dimensionless delta height and the dimensionless delta migration speed decrease. As the delta height increases, the water depth, the velocity approaching to the weir and the delta migration speed decrease.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.21 no.3
• /
• pp.48-62
• /
• 2018

In this study, landslide of debris flow occurred at 51 sites around Daeryounsan located in between Chuncheon-si and Hongcheon-gun during July in 2013 were investigated in field and behavior characteristics of debris flow were analyzed on the basis of records of rainfall and site investigation. According to debris flow types of channelized and hill slope, location and slope angle of initiation and deposit zone, and width and depth of erosion were investigated along entire runout of debris flow. DEM(Digital Elevation Model) of Daeryounsan was constructed with digital map of 1:5,000 scale. Land slide hazard was estimated using SINMAP(Stability INdex MAPping) and the predicted results were compared with field sites where debris flow occurred. As analyzed results, for hill slope type of debris flow, predicted sites were quite comparable to actual sites. On the other hand, for channelized type of debris flow, debris flow occurrence sites were predicted by using stability index associated with topographic wetness index. As analyzed results of 4 different conditions with the parameter T/R, Hydraulic transmissivity/Effective recharge rate, proposed by NRCS (Natual Resources Conservation Service), predicted results showed more or less different actual sites and the degree of hazard tended to increase with decrease of T/R value.