• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.349-357
• /
• 2019

Controlled low strength material(CLSM) has been developed using variety of material such as excavated soil, industrial by-product and industrial waste. But theses research limited at laboratory test and failed at commercialization. So in this paper evaluates CLSM used excavated soil characteristics such as flowability, bleeding rate, early strength for following process and 28day strength for re-excavatability. Also, various mix proportion of CLSM by water-binder ratio and soil-binder ratio were evaluated in laboratory. And derive the optimized CLSM mix proportion for using at field application test by movable batch plant. After applying CLSM at trench, evaluate core sample strength and excavatability by shovel, pickax and excavator for verify re-excavation. Furthermore, measure the level change after casting CLSM to inspect subsidence stability. As results of these assessments, not only confirmed the characteristics of CLSM at field but the fillability around pipe and subsidence stability.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5C
• /
• pp.229-237
• /
• 2009

A conventional way of backfilling has used sand or in-situ soil. It not only requires substantial amount of time and cost but also makes it particularly difficult to fill the bottom part and small cracks of a pipe. To address the problem with the conventional method of compaction, liquefied stabilized soil was proposed as an alternative because it reuses in-situ soil which can ensure sand supply while adjusting flowability and strength of the soil with design of mix proportion. With an aim to identify the mixing properties of liquefied stabilized soil depending on the organic content of in-situ soil, this study conducted indoor tests of material segregation, flowability, strength, and permeability by changing humic acid content of the soil. The results revealed that material segregation and flowability increased proportionally while strength decreased with the increased amount of humic acid. In the mean time, permeability of liquefied stabilized soil wasn't affected by organic content.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.275-282
• /
• 2002

High fluidity concrete needs high dosage of superplasticizer to acquire sufficient fluidity and high contents of fine powder and viscosity agents to prevent segregation. But it requires high manufacturing cost and has difficult in quality control. Therefore, in this paper, determination of optimal mixture proportion of segregation type superplasticizer for high fluidity concrete and manufacturing high fluidity concrete by applying developed segregation reducing type superplasticizer are discussed using flowing concrete method. According to test results, as dosage of superplasticizer increases, it shows that fluidity and bleeding increase, while air contents and ratio of segregation resistance decrease. It also shows that adding viscosity agent into it reduce bleeding and improve segregation resistance. Dosage of AE agent into it containing viscosity agent recovers loss of air contents during flowing procedure. Combination of proper contents of superplasticizer, viscosity agent and AE agent make possible to develope segregation reducing type superplasticizer Compressive strength of high fluidity concrete applying flowing method with it is higher than that of base concrete. No differences of compressive strength between compacting methods are found.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.9-15
• /
• 2018

According to the development and use of self-consolidating concrete in field, interest in material properties of early-age concrete is rising. Setting time with hydration process of cement is one of significant indicator to evaluate the early-age material properties of concrete, various nondestructive methods including penetration resistance measurement have been proposed to estimate setting time. This study performed an experimental approach to evaluate setting time delay in mortar adding superplasticizer using electrical resistivity measurement. For this purpose, total nine types of mortar samples were prepared, and its electrical resistivity was monitoring during 24h after mixing. From the experimental result, rising time of electrical resistivity was used to evaluate setting delay of mortar, and penetration resistance was also measured for comparison. In addition, dynamic elastic modulus and compressive strength of 1day mortar were measured to investigate a possibility the use of electrical resistivity measurement for evaluation of early-age material properties.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.3
• /
• pp.182-189
• /
• 2018

Controlled low strength material(CLSM), known as flowable fill is used sewer. This paper evaluates flowability, segregation, early strength and excavatability of CLSM made using standard soils such as SM, ML, CL, CH. Also, various mix proportions of CLSM containing kaolinite, red soil, Joomun Jin standard soil were developed and the mixing ratio optimized. It was considered as the flowability and early strength were severly affected by W/B, S/B, and early strength and flowability depend on standard soils which means the satisfaction conditions of CLSM were variety of standard soil conditions. Finally, not only optimal mixing proportions were deducted according to standard soil condition but confirmed effectiveness of bleeding and excavatability.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.5
• /
• pp.306-314
• /
• 2006

Instrumented indentation technique is a new way to evaluate nondestructive such mechanical properties as flow properties, residual stress and fracture toughness by analyzing indentation load-depth curves. This study evaluated quantitatively the flow properties of steels and residual stress of weldments. First, flow properties can be evaluated by defining a representative stress and strain from analysis of deformation behavior beneath the rigid spherical indenter and the parameters obtained from instrumented indentation tests. For estimating residual stress, the deviatoric-stress part of the residual stress affects the indentation load-depth curve, so that by analyzing the difference between the residual-stress-induced indentation curve and residual-stress-free curve, the quantitative residual stress of the target region can be evaluated. The algorithm for flow property evaluation was verified by comparison with uniaxial tensile test and the residual stress evaluation model was compared to mechanical cutting and ED-XRD results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5C
• /
• pp.303-312
• /
• 2006

This study is to evaluate the mechanical characteristics of flowable backfill and offer a guide line of mixture proportion based on soil types for constructing underground power utilities. Flowable backfill is known as soil-cement slurry, void fill, and controlled low-strength material(CLSM). The benefits of CLSM are reduced equipment costs, faster construction, re-excavation in the future, and the ability to place materials in confined spaces, which are narrow parts or perimeters of underground power cables nearly impossible for compaction. The flowable slurry mixed with 17 soils and 6 accelerated mixtures in the laboratory were evaluated for flowability and unconfined compressive strength to meet the target values of this study.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.5
• /
• pp.165-172
• /
• 2021

The purpose of this study is to investigate the carbon capture capacity of various inorganic materials. For this purpose, the change in property of ordinary Portland cement (OPC), blast furnace slag fine powder (GGBS), and circulating fluidized bed boiler ash (CFBC) due to carbonation were analyzed. Carbonation curing was performed on all specimens through the accelerated carbonation experiment, and the amount of carbon capture was quantitatively analyzed by thermogravimetric analysis according to the age of carbonation. From the results, it is confirmed that the carbon capture capacity was shown in all specimens. The carbon capture amount was shown in the order of CFBC, OPC, and GGBS. The 28-day carbon capture of CFBC, OPC, and GGBS was 3.9%, 1.3%, and 9.4%, respectively. Carbon capture reaction occurred rapidly at the beginning of carbonation, and occurred slowly with increasing age. SEM image analysis revealed that an additional product generated by carbonation curing in all specimens was calcium carbonate.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.154-154
• /
• 2003

고품질의 합금강 생산 시 가장 큰 영향을 미치는 레이들정련은 고온 하에서 반응 및 유동이 일어나므로 실제조업 직접관찰이나 측정이 대단히 어려울 뿐만 아니라, 수많은 조업인자와 상호 결합되어 있기 때문에 최적의 작업조건을 찾는데 많은 시행착오를 겪는다. 본 실험에서는 직접 조업하는 조건과 가장 부합하는 수모델 실험 및 Flow 3D를 이용한 수치해석 방법으로 비용의 절감 및 실험에 대한 위험부담 등 시행착오를 최소화하면서 최적의 작업조건을 도출하여 고품질 합금강 생산성과 process 효율성의 극대화를 찾을 수 있다. 따라서 본 연구에서는 슬래그의 물성(슬래그 양, 점도)을 고려한 gas bubbling 조건(가스유량, 유체높이, ladle 크기, 단공nozzle, porous plug 위치)에 따른 용강의 교반특성 및 용강의 슬래그 혼입 거동을 조사함으로써 고청정 용강 제조를 위한 최적 gas bubbling 조건을 설정하기 위한 수모델 실험과 수치해석 연구를 실시하였다. 수모델 실험을 통한 기포형성 거동과 용강의 교반특성에 대한 현상론적 연구와 병행하여, 유동장 측면에서 이상유동을 가정한 수치해석을 통해 실제 용강 래들 내에서의 거동을 정량화 하고자 한다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.43.1-43.1
• /
• 2009

다이캐스팅과 같이 가압 사출방식을 이용한 제품 성형 공정에서 관심의 대상이 되어왔던 연구 주제 중 하나는 어떻게 하면 금형 내에 충진되는 용탕의 유동을 층류성으로 제어할 수 있을까 하는 문제이다. 그러나 다이캐스팅 공정에서 일반적인 용탕의 사출속도로는 그 유동 특성을 제어하기가 거의 불가능하다. 이러한 사출속도의 설정 및 게이트의 형상설계를 하는데 있어서 대부분 경험적인 자료를 이용하고 있어 공정의 효율성을 극대화하고 있지 못한 실정이다. 본 연구에서는 용융 마그네슘합금이 금형내에 충진 될 때 유체의 유입속도 및 탕구형상이 유동에 미치는 영향을 전산유체역학을 이용하여 충진 및 응고해석을 하였고, 예견되는 제품의 결함 및 결함제어 가능성을 진단함으로써 개선방안을 제안하고 최종적으로 금형설계 제작에 반영하여 실제 주조된 제품을 해석결과와 비교하였다. 또한, 본 연구에서 주조된 전자기부품의 미세조직을 관찰하고, 인장강도 및 파괴 특성을 관찰 하였다. 실험결과 빠른 응고속도에 따른 조직의 미세화 효과로 항복강도, 인장강도 그리고 경도 특성이 우수하게 관찰되었다.